Eiki Projector Lc W4 User Manual

51
APPENDIX
System (1)SVGA 1SVGA 2SVGA 3
Auto PC Adj.Fine sync.Total dotsHorizontalVerticalCurrent modeClampDisplay area
Display area - HDisplay area - VFull screenResetMode freeStore
Quit
StandardRealImage 1Image 2Image 3Image 4
Image AdjustContrastBrightnessColor Temp
RedGreenBlue
Gamma
Store
Quit
FullZoomTrueDigital zoom +Digital zoom –
0 - 31
On/Off
0 - 630 - 63
InputDigital
Analog Go to System(1)
Input 2Y, Pb/Cb, Pr/Cr
Computer Input
Input 3
Go to System(2)
Go to System(2)
Input 1
Video 
S-Video
PC...

52
APPENDIX
AutoPALSECAMNTSCNTSC 4.43PAL-MPAL-N
Video Input
Auto
1080i501035i720p575p480p575i480i
StandardCinemaImage 1Image 2Image 3Image 4
Quit
FullZoom
0 - 630 - 630 - 630 - 63
Off/On
VolumeTreble0 - 63
Language
Image Select
System (3)
System (2)
Image AdjustContrastBrightnessColorTint
RedGreenBlueSharpness
ResetStore
Gamma
Progressive
0 - 630 - 630 - 630 - 150 - 15
Image 1Image 2Image 3Image 4
Screen
Sound
SettingEnglishGermanFrenchItalianSpanishPortugueseDutchSwedish
ChineseKoreanJapanese
On/Off...

53
Owner’s Manual (Print and CD-ROM)
AC Power Cord
Wireless/Wired Remote Control Transmitter and Batteries
Remote Control Cable
DVI-VGA Cable and DVI Cable
3 Types Control Cable (For PS/2, Serial and ADB port) 
3 Types Light-Block Sheet (For option lens)
2 Types Lens Attachment (For option lens)
Protective Dust Cover
Real Color ManagerAccessories
TECHNICAL SPECIFICATIONS
1.21 TFT Active Matrix type, 3 panels
Multi-media Projector
46.3 lbs (21 kg)
17.3 x 9.1 x 23.8 (439 mm x 230 mm x 605.6 mm) 
1366 x 768...

54
APPENDIX
Vcc
- Data
+ Data
Ground
1
2
3
4
USB PORT TERMINAL
Pin Configuration
Connect USB port output terminal of computer or peripheral equipment to this terminal with USB port  Cable (not
supplied).
2
341
CONFIGURATIONS OF TERMINALS
Terminal : Mini DIN 8-PIN
Connect control port (PS/2, Serial or ADB port) on your computer to this terminal with Control Cable (supplied).
12
345876
Pin Configuration
-----
CLK
DATA
GND
-----
-----
GND
-----
R X D
-----
-----
GND
RTS
T X D
GND
GND
-----
ADB
-----
GND...

55
APPENDIX 

©2006 Eiki International, Inc.
U.S.A.
EIKI International, Inc.
30251 Esperanza
Rancho Santa Margarita
CA 92688-2132
U.S.A.
Tel : 800-242-3454 (949)-457-0200 
Fax : 800-457-3454 (949)-457-7878
E-Mail : [email protected]
Canada
Deutschland & Österreich
EIKI Deutschland GmbH
Am Frauwald 12 
65510 Idstein
Deutschland
Tel : 06126-9371-0 
Fax : 06126-9371-14
E-Mail : [email protected]
Eastern Europe
EIKI CZECH spol. s.r.o.
Umelecká 15
170 00 Praha 7 
Czech Republic
Tel : +42 02 20570024
+42 02 20571413 
Fax : +42 02...

- 1 -
E
LCD PROJECTOR
LENS REPLACEMENT AND INSTALLATION PROCEDURES
CAUTION
When installing or replacing the Projection Lens, refer to this manual. For installation of
the lens, use the parts designated in the manual. Do not use the installation manual and
Light-Block Sheets in the lens package.
Check the following parts supplied to this projector.
NOTES ON LENS INSTALLATION
●Lens installation and replacement should be made by the qualified service
personnel.
●Be sure to install the lens following this...

- 2 -
E
NOTE: The installation procedure and needed
parts for lens installation depend on the type of
the Projection Lens. Check the Model No. of
the Projection Lens and be sure to install or
replace the lens following the procedure below.
1  
Remove the Lower Lens Cover. Remove the two
(2) Screws A. Push the part Band pull the Lower
Lens Cover down. (See Fig. 1.)
2  
Remove the four (4) Screws C. Pull the Upper
Lens Cover toward the front and remove. 
(See Fig. 2.)
3  
Remove the two (2) Screws Dand the...

- 3 -
E
LENS LOCK RELEASE
LENS LOCK SCREW
DRIVER 
IN THE LENS
LOCATE MOTOR
ON RIGHT SIDELENS ATTACHMENT
Part No. (610 275 6029)
Fig-4
Fig-6Fig-7
LENS LOCK
LEVER
LENS LOCK 
4  
Replace the Lens Cap on the rear (mounting side) of the Projection Lens and mount a lens on
the Lens Attachment with four (4) Screws. (Use the screws attached on the lens.)
Connect the Lens Motor Lead connector to the socket on the right-top of the Lens Attachment
(Motor Driven Lens only). See Fig. 5.
When installing the LNS-W01,...

- 4 -
E
6  
This projector has three Light-Block Sheets. Use the Light-Block Sheet corresponding with the lens. (Refer
to the list below.)  
Set the Light-Block Sheet through the lens. 
Make sure the shape of the Light-Block Sheets are correct and be sure to set them as shown in the Fig. 8.
NOTE:
●Be sure to set each Light-Block Sheet as shown in Fig. 8.
●Make sure the mark (TOP and BACK) on the Light-Block Sheets are correct and set them properly.
Light-Block Sheets for each lens.
Lens Model No....