Eiki Projector Lc W4 User Manual

21
BASIC OPERATION
TURNING ON PROJECTOR
TURNING OFF PROJECTOR
TURNING ON / OFF PROJECTOR 
Power off?
Message disappears after 4 seconds.
Connect a projectors AC Power Cord into a wall outlet and turn
MAIN ON / OFF SWITCH to ON. LAMP indicator lights RED,
and READY indicator lights GREEN.
Press POWER ON-OFF button on Top Control or on Remote
Control Unit to ON. LAMP indicator dims, and Cooling Fans start
to operate. Preparation Display appears on a screen and count-
down starts.  Signal from source...

22
KEYSTONE ADJUSTMENT
1Press KEYSTONE button on Remote Control Unit or select
Keystone on SETTING menu.  (Refer to page 39.)  Keystone
dialog box appears.
2Correct keystone distortion by pressing POINT LEFT/RIGHT
button(s).  Press POINT LEFT button to reduce left part of
image, and press  POINT RIGHT button to reduce right part.  
If a projected picture has keystone distortion, correct image with KEYSTONE adjustment.
ADJUSTING SCREEN
Message disappears after 4 seconds.
Message disappears after 4...

23
Press FREEZE button on Remote Control Unit to freeze picture on-screen.  To cancel FREEZE function, press FREEZE
button again or press any other button except POINT / SELECT / RIGHT CLICK /  LASER button.
PICTURE FREEZE FUNCTION
Press NO SHOW button on Remote Control Unit to black out a image.
To restore to normal, press NO SHOW button again or press any other
button except POINT / SELECT / RIGHT CLICK /  LASER button.
NO SHOW FUNCTION
Message disappears after 4 seconds.
No show
Press P-TIMER button...

24
BASIC OPERATION
1
2
Press MENU button and ON-SCREEN MENU will appear.  Press
POINT LEFT/RIGHT buttons to move a red frame pointer to
SOUND Menu icon. 
Volume
Press VOLUME (+/–) button(s) on Top Control or on Remote Control
Unit to adjust volume.  Volume dialog box appears on screen for a few
seconds.
(+) button to increase volume, and (–) button for decreasing.
Mute
Press MUTE button on Remote Control Unit to cut off sound.  To
restore sound to its previous level, press MUTE button again or press...

25
COMPUTER INPUT
Press MENU button and ON-SCREEN MENU will appear.  Press
POINT LEFT/RIGHT button to move a red frame pointer to
INPUT Menu icon.
Move a pointer to  RGB, and then press SELECT button.  
1
3
When connect a computer output [5 BNC Type (Red, Green, Blue,
Horiz. Sync and Vert. Sync.)] from a computer to R/Pr, G/Y, B/Pb, H/HV
and V jacks.
WHEN SELECT INPUT 2 (5 BNC INPUT JACKS )
SELECTING COMPUTER SYSTEM
WHEN SELECT  INPUT 1 (DVI INPUT TERMINAL )
Press MENU button and ON-SCREEN MENU will...

26
COMPUTER INPUT
This projector automatically tunes to most different types of computers based on VGA, SVGA, XGA, SXGA, WXGA or UXGA
(refer to “COMPATIBLE COMPUTER SPECIFICATIONS” on page 27).  When selecting Computer, this projector
automatically tunes to incoming signal and projects proper image without any special setting.  (Some computers need setting
manually.)
Note : Projector may display one of following messages.
When projector cannot recognize connected signal as PC
system provided in this...

27
COMPUTER INPUT
COMPATIBLE COMPUTER SPECIFICATIONS
Basically this projector can accept a signal from all computers with V, H-Frequency mentioned below and less
than 230 MHz of Dot Clock.
–––––––– 
(Interlace)
1024 x 768
(Interlace)
ON-SCREEN
DISPLAYRESOLUTIONH-Freq.
(kHz)V-Freq.
(Hz)
VGA 1640 x 48031.4759.88
VGA 2720 x 40031.4770.09
VGA 3640 x 40031.4770.09
VGA 4640 x 48037.8674.38
VGA 5640 x 48037.8672.81
VGA 6640 x 48037.5075.00
MAC LC13640 x 48034.9766.60
MAC 13640 x 48035.0066.67
MAC 16832 x...

28
COMPUTER INPUT
PC ADJUSTMENT
AUTO PC ADJUSTMENT
Auto PC Adjustment function is provided to automatically adjust Fine sync, Total dots and Picture Position to conform to your
computer.  Auto PC Adjustment function can be operated as follows.
Press MENU button and ON-SCREEN MENU will appear.  Press
POINT LEFT/RIGHT button to move a red frame pointer to PC
ADJUST Menu icon.1
2Press POINT DOWN button to move a red frame pointer to
AUTO PC Adj. icon and then press SELECT button twice.
This Auto PC...

29
COMPUTER INPUT
MANUAL PC ADJUSTMENT
This projector can automatically tune to display signals from most personal computers currently distributed.  However, some
computers employ special signal formats which are different from standard ones and may not be tuned by Multi-Scan system
of this projector.  If this happens, projector cannot reproduce a proper image and image may be recognized as a flickering
picture, a non-synchronized picture, a non-centered picture or a skewed picture.
This projector has a...

30
NOTE :  Fine sync, Display area, Display area H, Display area V and
Full screen can not be adjusted when “480i”, “575i”, “480p”,
“575p”, “720p (HDTV)”, “1035i (HDTV)”, “1080i50(HDTV)” or
“1080i60 (HDTV)” is selected on PC SYSTEM Menu (P26).
Selects area displayed with this projector.  Select resolution at
Display area dialog box.
Display area
Adjustment of horizontal area displayed with this projector.  Press
POINT LEFT/RIGHT button(s) to decrease/increase value and then
press SELECT button.
Display...