Eiki Projector Lc Sd12 User Manual

41
Maintenance and Cleaning
Apply a non-abrasive camera lens cleaner to a soft, dry cleaning
cloth.  Avoid using an excessive amount of cleaner.  Abrasive
cleaners, solvents or other harsh chemicals might scratch a
surface.
When the projector is not in use, replace the Lens Cover.
2
4
Lightly wipe Projection Lens with a cleaning cloth.3
Follow these steps to clean the projection lens:
Cleaning the Projector Cabinet
Disconnect the AC power cord before cleaning.1
Lightly wipe the projector body with a...

42
When the life of the projection lamp draws to an end, LAMP
REPLACE indicator lights yellow.  If this indicator lights yellow,
replace the projection lamp with a new one promptly.
ORDER REPLACEMENT LAMP
Replacement Lamp can be ordered through your dealer.  When ordering a projection lamp, give the following
information to the dealer.
•Model No. of your projector   : LC-SD12
•Replacement Lamp Type No. : POA-LMP57
(Service Parts No. 610 308 3117)
For continued safety, replace with the lamp assembly of...

43
Maintenance and Cleaning
Lamp Replace Counter
Be sure to reset the lamp replace counter after Lamp Assembly is replaced.  When the lamp replace counter is reset, the
LAMP REPLACE Indicator stops lighting.
Note : –Do not reset the Lamp Replace Counter until after the projection lamp is replaced.
Turn projector on, press the MENU button to display the
On-Screen Menu.  Press the Point 
7 8buttons to move the
red frame pointer to the Setting Menu icon.
Press the Point dbutton to move the red frame pointer...

44
Troubleshooting
Before calling your dealer or service center for assistance, check the matters below once again.
–  Make sure you have properly connected the projector to peripheral equipment as described in the section Installation on
P15-16. 
–   Make sure all equipment is connected to AC outlet and turned on the power.
–   When you operate the projector with a computer, and it does not project an image, restart the computer.
No power.
–  Plug the projector into your AC outlet.
–  Make sure if the...

45
This symbol on the nameplate means the product is Listed by Underwriters
Laboratories Inc.  It is designed and manufactured to meet rigid U.L. safety standards
against risk of fire, casualty and electrical hazards.
Appendix
WARNING :
High voltages are used to operate this projector.  Do not attempt to open the cabinet.
If the problem still persists after following all operating instructions,
contact the sales dealer where you purchased the
projector or the service center.Give the model number and...

46
Appendix
Check the indicators for projector condition.  
• • • lights green.• • • lights red.• • • off• • • flashes green.
✽When the life of the projection lamp draws to an end, the LAMP REPLACE indicator lights yellow.  When this indicator lights
yellow, replace the projection lamp with a new one promptly.  Reset the Lamp replace counter after replacement of the lamp.  
( ☞ P42-43 )
The projector is OFF.  (The AC power cord is unplugged.)
The projector is preparing for stand-by or the projection lamp...

47
Appendix
Menu Tree
MODE 1MODE 2SVGA 1- - - -
Auto PC Adj.Fine syncTotal dotsHorizontalVerticalCurrent mode
ClampDisplay area
Display area HDisplay area VFull screenReset
Store
Quit
StandardRealImage 1Image 2Image 3Image 4
Image AdjustContrastBrightnessColor temp.
RedGreenBlue
Gamma
Store
Quit
NormalTrueWideDigital zoom +Digital zoom –
0 - 31
On / Off
0 - 630 - 63
InputRGB 
Component 
Computer Input
Main menu
Main menu
VideoAuto
Computer 
Video 
S-Video
PC Adjust
640 x 480720 x 400800 x 6001024 x...

48
Appendix
AutoPALSECAMNTSCNTSC4.43PAL-MPAL-N
Main menu
Video Input
Auto1080i1035i720p575p480p575i480i
StandardCinemaImage 1Image 2Image 3Image 4
Quit
NormalWide
0 - 630 - 630 - 630 - 63
On / Off
Main menu
Settings
VolumeMuteQuitOn / Off
Language
Image Select
Image AdjustContrastBrightnessColorTint
RedGreenBlueSharpness
ResetStore
Gamma
Progressive
0 - 630 - 630 - 630 - 150 - 15
Image 1
Screen
Sound
SettingEnglishGermanFrenchItalianSpanishPortugueseDutchSwedish
ChineseKoreanJapanese
Store / ResetOn /...

49
Appendix
Compatible Computer Specifications
Basically this projector can accept the signal from all computers with the V, H-Frequency below mentioned and less than
100 MHz of Dot Clock.
Note:
–Specifications are subject to change without notice.
ON-SCREEN
DISPLAYRESOLUTIONH-Freq.
(kHz)V-Freq.
(Hz)
VGA 1640 x 48031.4759.88
VGA 2720 x 40031.4770.09
VGA 3640 x 40031.4770.09
VGA 4640 x 48037.8674.38
VGA 5640 x 48037.8672.81
VGA 6640 x 48037.5075.00
MAC LC13640 x 48034.9766.60
MAC 13640 x 48035.0066.67
MAC...

50
Appendix
Technical Specifications
0.5 TFT Active Matrix type, 3 panels
Multi-media Projector
4.6lbs (2.1 kg)
10.63 x 3.07 x 7.48 (270mm x 78.0mm x 190mm) (not including Adjustable Feet)
800 x 600 dots
1,440,000 (800 x 600 x 3 panels)
PAL, SECAM, NTSC, NTSC4.43, PAL-M and PAL-N
H-sync. 15 ~ 80 KHz, V-sync. 50 ~ 100 Hz
Adjustable from 34” to 200”
1 speaker, ø1.3 (32mm) 
41 ˚F – 95 ˚F (5 ˚C – 35 ˚C)
14 ˚F – 140 ˚F (-10 ˚C – 60 ˚C)
Owner’s Manual
AC Power Cord
Remote Control and Battery
VGA Cable
Carrying...