Eiki Projector Lc Sd12 User Manual

31
Video input
Input Source Selection ( Component, RGB Scart 21-pin )
Menu Operation Direct Operation
Choose Computer by pressing the INPUT button on the top control or
the COMPUTER button on the remote control.
Before using these buttons, correct input source should be selected
through menu operation as described below.
Press the MENU button to display the On-Screen Menu.  Press
the Point 
7 8buttons to move the red frame pointer to the
Input Menu icon.
Press the Point dbutton to move the red arrow...

32
Video Input
AV SYSTEM MENU (VIDEO OR S-VIDEO)
AV SYSTEM MENU (COMPONENT VIDEO)
Video System Selection
Press the MENU button to display the On-Screen Menu.  Press
the Point 
7 8buttons to move the red frame pointer to the AV
System Menu icon.
Press the Point dbutton to move the red arrow pointer to the
system that you want to select and then press the SELECT
button.
1
2
If projector cannot reproduce proper video image, it is necessary to
select a specific broadcast signal format among PAL, SECAM,...

33
Video Input
Menu Operation
Press the MENU button to display the On-Screen Menu.  Press
the Point 
7 8buttons to move the red frame pointer to the
Image Select Menu icon.1
2Press the Point d dbutton to move the red frame pointer to the
level that you want to set and then press the SELECT button.
Move the red frame pointer to the
level and press the SELECT button.
The level being selected.
IMAGE SELECT MENU
Normal picture adjustment preset on this projector.Standard
Picture level adjusted for the...

34
Video Input
Press the Point 7 8buttons
to adjust the value.
Press the MENU button to display the On-Screen Menu.   Press
the Point 
7 8buttons to move the red frame pointer to the
Image Adjust Menu icon.1
2Press the Point dbutton to move the red frame pointer to the
item you want to adjust and then press the SELECT button.  The
level of each item is displayed.  Adjust each level by pressing
the Point 
7 8buttons.
Move the red frame pointer
to the item to be selected
and then press the SELECT
button....

35
Video Input
To store the adjusted data, move the red frame pointer to the
Store icon and press the SELECT button to display the Image
Level Menu.  Move the red frame pointer to the Image Level 1
to 4 and then press the SELECT button.
A confirmation box will appear and select [Yes]. 
Image Level Menu
Move the red frame
pointer to the image
icon to be set and
then press the
SELECT button.
Store icon
Reset all adjustments to previous figures.
Reset
Store
Close the Image Menu.
Quit
When this function is...

36
Keystone
This function corrects distortion of a projected image.  Select either
Store or Reset with the Point 
7 8buttons, and then press the Select
button.  The keystone dialog box appears.  Adjust keystone with the
Point 
e ed
d
7 8buttons. 
Store . . . . . stores the keystone adjustment even if the AC power
cord is disconnected.
Reset  . . . . .resets the keystone adjustment when the AC power
cord is disconnected.
Setting Menu
Press the MENU button to display the On-Screen Menu.  Press
the Point 
7...

37
Setting
For reducing power consumption as well as maintaining the lamp
life, Power management function turns off the projection lamp when
the input signal is interrupted and no button is pressed for 30
seconds or more. 
If the input signal is interrupted and no button is pressed for 30
seconds or more, the timer display with the message  No signal
appears on the screen.  The count-down of the set time will get
started.  The count-down time can be set between 1 and 30
minutes. 
When the count-down time...

38
Setting
Remote control
This projector has two different remote control codes; the factory-
set normal code (Code 1) and the secondary code (Code 2).  This
switching function prevents remote control interference when
operating several projectors or video equipment at the same time.  
When operating the projector in “Code 2,” both the projector and
remote control must be switched to “Code 2.”  
To change the code of the projector :
Set the remote control in the SETTING MENU to “Code 2.”
To change the...

39
Wa rn ing Indicator
The WARNING indicator shows the state of the function which protects the projector.  Check the state of the WARNING
indicator and the POWER indicator to take proper maintenance. 
POWERLAMP
REPLACE WARNING
IN
F
WARNING
flashing red
Top Control
The projector is shut down and the WARNING indicator is flashing red
When the temperature inside the projector exceeds the normal
temperature, the projector is automatically shut down to protect the
inside of the projector.  The POWER...

40
Maintenance and Cleaning
Turn off the projector, and disconnect AC power cord from the
AC outlet.
Turn the projector upside down and remove air filters by pulling
the latches upward.
1
2
Removable air filters prevent dust from accumulating on the surface of optical elements inside the projector.  Should air
filters become clogged with dust particles, it will reduce the cooling fans effectiveness and may result in internal heat build
up and adversely affect the life of the projector.  Clean air filters...