Eiki Projector Lc Sd12 User Manual

21
Basic Operation
Message disappears after 4 seconds.
Press the P-TIMER button on the remote control.  The timer display
“00 : 00” appears on the screen and the timer starts to count time (00
: 00 ~ 59 : 59).  
To stop P-Timer display, press the P-TIMER button.  And then, press
the P-TIMER button again to cancel P-Timer function.
1
2
Press the MENU button to display the On-Screen Menu.  Press
the Point 
78buttons to move the red frame pointer to Sound
Menu icon.  Volume
Press the VOLUME +/– buttons on...

22
Menu Operation Direct Operation
Choose Computer by pressing the INPUT button on the top control or
the COMPUTER button on the remote control.
Before using these buttons, correct input source should be selected
through menu operation as described below.
Press the MENU button to display the On-Screen Menu. Press
the Point 
7 8buttons to move the red frame pointer to Input
Menu icon.
Press the Point dbutton to move the red arrow pointer to
Computer and then press the SELECT button.  The Source
Select...

23
Computer Input
Computer System Selection
This projector automatically tunes to various types of computers based on VGA, SVGA, XGA or SXGA with its Multi-scan
system and Auto PC Adjustment.  If Computer is selected as a signal source, this projector automatically detects the signal
format and tunes to project a proper image without any additional setting.  (Signal formats provided in this projector is
shown on page 49 )
When projector cannot recognize connected signal as PC
system provided in this...

24
Computer Input
Auto PC Adjustment
Auto PC Adjustment function is provided to automatically conform Fine sync, Total dots and Picture Position to your
computer.  This function can be operated as follows.
Press the MENU button to display the On-Screen Menu.  Press
the Point 
7 8buttons to move the red frame pointer to the PC
Adjust Menu icon.1
2Press the Point dbutton to move the red frame pointer to the
Auto PC Adj. icon and then press the SELECT button twice.
This Auto PC Adjustment can be also...

25
Computer Input
Manual PC Adjustment
Some computers employ special signal formats which may not be tuned by Multi-Scan system of this projector.  In this
case, the projector cannot reproduce a proper image and the image may be recognized as a flickering picture, a non-
synchronized picture, a non-centered picture or a skewed picture.
The Manual PC Adjustment function allows you to precisely adjust several parameters to match those special signal
formats. You can store those adjusted parameters in the 5...

26
Computer Input
Note:
Display area, Display area (H/V) and Full screen cannot be adjusted when
480p, 575p, 480i, 575i, 720i(HDTV) , 1035i(HDTV) or 1080i(HDTV) is selected
on PC SYSTEM Menu.  (
☞P23 ).
Select area displayed with this projector.  Select the resolution at the
Display area dialog box.Display area
Adjust the horizontal area displayed with this projector.  Press the
Point 
7 8buttons to decrease/increase value to match the
resolution of image. Then press the SELECT button.Display area H...

27
Computer Input
Menu Operation
Press the MENU button to display the On-Screen Menu. Press
the Point 
7 8buttons to move the red frame pointer to the
Image Select Menu icon.1
2Press the Point dbutton to move the red frame pointer to the
level that you want to set and then press the SELECT button.Move the red frame pointer to the
level and press the SELECT button.
The level being selected.
IMAGE SELECT MENU
Normal picture adjustment preset on this projector.Standard
Picture adjustment improved in...

28
Computer Input
Image Level Menu
Move the red frame
pointer to any of
Image 1 to 4 where
you want to set  and
then press the
SELECT button.
Reset all adjustments to previous figures.
Reset
Store
Close the Image Adjust Menu.
Quit
To store manually preset image, move the red frame pointer to the
Store icon and press the SELECT button to display the Image Level
Menu.  Move the red frame pointer to the Image 1 to 4 where you
want to set and then press the SELECT button.
A confirmation box will appear and...

29
Computer Input
Screen Size Adjustment
This projector has a picture screen resize function, which enables you to customize the  image size.
Press the MENU button to display the On-Screen Menu.  Press
the Point 
7 8buttons to move the red frame pointer to the
Screen Menu icon.
When Digital zoom + is selected, the On-Screen Menu disappears
and the message “D. Zoom +” is displayed.  Press the SELECT
button to expand image size.  And press the Point 
e d 7 8buttons
to pan the image.  The panning function...

30
Input Source Selection ( Video, S-Video )
Menu Operation Direct Operation
Choose Video by pressing the INPUT button on the top control or the
VIDEO button on the remote control.
Before using these buttons, correct input source should be selected
through menu operation as described below.
Press the MENU button to display the On-Screen Menu.  Press
the Point 
7 8buttons to move the red frame pointer to the
Input Menu icon.
Press the Point dbutton to move the red arrow pointer to Video
and then press the...