Eiki Projector Lc Sd12 User Manual

							21
Basic Operation
Message disappears after 4 seconds.
Press the P-TIMER button on the remote control.  The timer display
“00 : 00” appears on the screen and the timer starts to count time (00
: 00 ~ 59 : 59).  
To stop P-Timer display, press the P-TIMER button.  And then, press
the P-TIMER button again to cancel P-Timer function.
1
2
Press the MENU button to display the On-Screen Menu.  Press
the Point 
78buttons to move the red frame pointer to Sound
Menu icon.  Volume
Press the VOLUME +/– buttons on the remote control or on the top
control to adjust volume.  The volume dialog box appears on the
screen for a few seconds.
The VOLUME + button to increase volume, and the VOLUME –
button for decreasing.
Mute
Press the MUTE button on the remote control to cut off sound.  To
restore sound to its previous level, press the MUTE button again or
press Volume +/–.
To increase volume, Press the Point 8button, and Press the Point 7
button to decrease volume. 
Press the Point 78 buttons to mute the sound.  Dialog box display is
changed to “On” and sound is muted.  To restore sound to its
previous level, press the Point 
78buttons again.
Press the Point dbutton to move the red frame pointer to the
item that you want to select, and then press the SELECT button.
Indicates approximate
level of volume.
Close Sound Menu.
Direct Operation
Menu Operation
Volume
Mute
Indicates approximate 
level of volume.
The display disappears after 4 seconds.  
SOUND MENU
Sound Menu icon
Sound Adjustment P-Timer Function No Show Function
Press the MUTE button to set
Mute function On or Off.
Press the NO SHOW button on the remote control to black out the
image.  To restore to normal, press the NO SHOW button again or
press any other button.  When a projected image is captured and set
as “User” in the Logo item in the Setting menu ( ☞ P36 ), the screen
changes each time you press the NO SHOW button as follows :
black out ➜the captured image ➜normal ➜......
Basic Operation 
						

							22
Menu Operation Direct Operation
Choose Computer by pressing the INPUT button on the top control or
the COMPUTER button on the remote control.
Before using these buttons, correct input source should be selected
through menu operation as described below.
Press the MENU button to display the On-Screen Menu. Press
the Point 
7 8buttons to move the red frame pointer to Input
Menu icon.
Press the Point dbutton to move the red arrow pointer to
Computer and then press the SELECT button.  The Source
Select Menu will appear. 
1
2
INPUT button
Computer
Video
INPUT MENU
Input Menu icon
Input Source Selection
Computer Input
Move the pointer to the correct input source and press the
SELECT button. 3
When the input source is coming from a computer
through the COMPUTER IN / COMPONENT IN
terminal, select RGB. RGB 
RGB (Scart)
Component See P31Input Source Selection (Component, RGB-
Scart 21-pin ) . 
Move the pointer (red
arrow) to Computer and
press the SELECT button.
Move the pointer to RGB and
press the SELECT button.
Source Select Menu
See P31 Input Source Selection (Component, RGB-
Scart 21-pin ) .  
						

							23
Computer Input
Computer System Selection
This projector automatically tunes to various types of computers based on VGA, SVGA, XGA or SXGA with its Multi-scan
system and Auto PC Adjustment.  If Computer is selected as a signal source, this projector automatically detects the signal
format and tunes to project a proper image without any additional setting.  (Signal formats provided in this projector is
shown on page 49 )
When projector cannot recognize connected signal as PC
system provided in this projector, Auto PC Adjustment
function operates to adjust projector and the message
“Auto” is displayed on the System Menu icon.  When
image is not provided properly, manual adjustment is
required.  ( ☞ P25 - 26 )
There is no signal input from computer.  Make sure the
connection of computer and a projector is set correctly.  
( ☞  Troubleshooting P44 )
Auto
-----
System Menu icon
Displays system being
selected.
PC SYSTEM MENU
Selecting Computer System Manually
System Menu icon 
Displays system being selected.
The systems on this dialog box
can be selected.
Press the MENU button to display the On-Screen Menu. Press
the Point 
7 8buttons to move the red frame pointer to PC
System Menu icon.
Press the Point dbutton to move the red arrow pointer to the
system that you want to set, and then press 
the SELECT button.  
1
2
PC SYSTEM MENU
Custom Mode (1–5) set in PC
Adjust Menu.  ( ☞ P25-26 )
PC system can be also selected manually.
Note : The projector may display one of the following messages.
User preset adjustment in Computer Adjustment.
Adjustment data can be stored in Mode 1 - 5.  ( ☞  P25-
26 )  Mode 1
Computer systems provided in the projector.  The
projector chooses a proper system and displays it.  SVGA 1
*Mode 1 and SVGA 1 are examples.  
Computer Input 
						

							24
Computer Input
Auto PC Adjustment
Auto PC Adjustment function is provided to automatically conform Fine sync, Total dots and Picture Position to your
computer.  This function can be operated as follows.
Press the MENU button to display the On-Screen Menu.  Press
the Point 
7 8buttons to move the red frame pointer to the PC
Adjust Menu icon.1
2Press the Point dbutton to move the red frame pointer to the
Auto PC Adj. icon and then press the SELECT button twice.
This Auto PC Adjustment can be also executed by pressing the
Auto PC button on the remote control.Move the red frame pointer to Auto PC
Adj. icon and press the SELECT button.
PC ADJUST MENU Auto PC Adj.
PC Adjust Menu icon
To store adjustment parameters :
Adjustment parameters from Auto PC Adjustment can be memorized
in this projector.  Once parameters are memorized, the setting can be
done just by selecting Mode in PC System Menu  (☞ P23 ).  Refer to 
 Store  of Manual PC Adjustment section  (☞ P26 ).
Note :
– Fine sync, Total dots and Picture Position of some computers can not be
fully adjusted with this Auto PC Adjustment function.  When the image is
not provided properly through this function, manual adjustments are
required.  ( 
☞P25, 26 )
– Auto PC Adjustment function cannot be operated when 480p, 575p, 480i,
575i, 720p (HDTV), 1035i (HDTV) or 1080i (HDTV) is selected on PC
SYSTEM Menu.  ( 
☞P23). 
						

							25
Computer Input
Manual PC Adjustment
Some computers employ special signal formats which may not be tuned by Multi-Scan system of this projector.  In this
case, the projector cannot reproduce a proper image and the image may be recognized as a flickering picture, a non-
synchronized picture, a non-centered picture or a skewed picture.
The Manual PC Adjustment function allows you to precisely adjust several parameters to match those special signal
formats. You can store those adjusted parameters in the 5 independent memory areas, enabling you to call up whenever
you need.
Press the MENU button to display the On-Screen Menu. Press
the Point 
7 8buttons to move the red frame pointer to the PC
Adjust Menu icon.1
2Press the Point dbutton to move the red frame pointer to the
item that you want to adjust and then press the SELECT button
to display the adjustment dialog box.  Press the Point 
7 8
buttons to adjust the value.
Move the red frame pointer to the item
and press the SELECT button.
PC ADJUST MENU
PC Adjust Menu icon
Adjust an image as necessary to eliminate flicker from the display.
Press the Point 
7 8buttons to adjust the value.(From 0 to 31.) Fine sync
Adjust the number of total dots in one horizontal period.  Press the
Point 
7 8buttons and adjust number to match your PC image. Total dots
Adjust horizontal picture position.  Press the Point 7 8buttons to
adjust the position.Horizontal
Adjust vertical picture position.  Press the Point 7 8buttons to
adjust the position.Vertical
Press the SELECT button to show the information of computer
selected.Current mode
Adjust clamp level.  When the image has dark bars, try this
adjustment.Clamp
Press the SELECT button at this
icon to adjust “Clamp,” “Display
area (H/V)” or set “Full screen.”
Press the Point 7 8buttons
to adjust the value.Shows status
(Stored / Free) of the
selected Mode. Selected Mode
Press the SELECT button at
the Current Mode icon to
show the information of the
computer connected.
Current mode
Computer Input 
						

							26
Computer Input
Note:
Display area, Display area (H/V) and Full screen cannot be adjusted when
480p, 575p, 480i, 575i, 720i(HDTV) , 1035i(HDTV) or 1080i(HDTV) is selected
on PC SYSTEM Menu.  (
☞P23 ).
Select area displayed with this projector.  Select the resolution at the
Display area dialog box.Display area
Adjust the horizontal area displayed with this projector.  Press the
Point 
7 8buttons to decrease/increase value to match the
resolution of image. Then press the SELECT button.Display area H
Adjust the vertical area displayed with this projector.  Press the Point
7 8buttons to decrease / increase the value to match the resolution
of the image. Then press the SELECT button.Display area V
Press the Point 7 8buttons to switch Full screen function to  “On”
or “Off.”  Set “On” to resize the image with 4 x 3 aspect ratio to fit
the screen. Full screen
Reset
Store
Close PC Adjust Menu.
Quit
To store adjustment parameters, move the red frame pointer to the
Store icon and then press the SELECT button.  Move the red arrow
pointer to any of Mode 1 to 5 that you want to store to and then
press the SELECT button.
Reset all adjust parameters on adjustment dialog box to previous
figures.
Mode free
Vacant Mode
Close this dialog box.
To store adjustment data To clear adjustment data
To clear adjustment parameters previously set, move the red frame
pointer to the Mode free icon and then the SELECT button.  Move
the red arrow pointer to the Mode that you want to clear and then
press the SELECT button.
Press the SELECT button at the
Display area icon to show the
Display area dialog box.
Display area
This Mode has parameters being stored.
Shows values of “Total
dots,” “Horizontal,”
“Vertical,” “Display area H,”
and “Display area V.” 
						

							27
Computer Input
Menu Operation
Press the MENU button to display the On-Screen Menu. Press
the Point 
7 8buttons to move the red frame pointer to the
Image Select Menu icon.1
2Press the Point dbutton to move the red frame pointer to the
level that you want to set and then press the SELECT button.Move the red frame pointer to the
level and press the SELECT button.
The level being selected.
IMAGE SELECT MENU
Normal picture adjustment preset on this projector.Standard
Picture adjustment improved in reproduction of halftones.  This
adjustment is suitable for providing better image in brighter place.Real
User preset picture adjustment in Image Adjust Menu ( ☞ P28 ). Image 1~4
Image Select
Menu icon
Direct Operation
Select image level among Standard, Real, Image 1, Image 2, Image 3
and Image 4 by pressing the IMAGE button on the remote control.IMAGE button
Standard
Real
Image 1
Image 2
Image 3
Image 4
Normal picture adjustment preset on this projector.  
Picture adjustment improved in reproduction of halftones.  This
adjustment is suitable for providing better image in brighter place.
User preset picture adjustment in Image Adjust Menu (☞ P28 ). Standard
Real
Image 1~4
Image Level Selection
Computer Input 
						

							28
Computer Input
Image Level Menu
Move the red frame
pointer to any of
Image 1 to 4 where
you want to set  and
then press the
SELECT button.
Reset all adjustments to previous figures.
Reset
Store
Close the Image Adjust Menu.
Quit
To store manually preset image, move the red frame pointer to the
Store icon and press the SELECT button to display the Image Level
Menu.  Move the red frame pointer to the Image 1 to 4 where you
want to set and then press the SELECT button.
A confirmation box will appear and select Yes. 
Press the Point 7 8buttons
to adjust the value.
Press the MENU button to display the On-Screen Menu.  Press
the Point 
7 8buttons to move the red frame pointer to the
Image Adjust Menu icon.1
2Press the Point dbutton to move the red frame pointer to the
item that you want to adjust, and then press the SELECT button.
The level of each item is displayed.  Adjust each level by
pressing the Point 
7 8buttons.Move the red frame pointer to
the item to be selected and
then press the SELECT button.
IMAGE ADJUST MENU
Image Level Adjustment
Store icon
Press the SELECT button at this
icon to store the adjustment.Image Adjust
Menu icon
Selected Image level
Press the Point 7 8 buttons to adjust the image contrast. 
(From 0 to 63.)
Press the Point 7 8buttons to adjust the image brightness.  
(From 0 to 63.)Contrast
Brightness
Press the Point 7 8buttons to obtain better balance of contrast.
(From 0 to 15.)Gamma
Press the Point 7 8buttons to adjust the red tone.  (From 0 to 63.) White balance (Red)
Press the Point 7 8buttons to adjust the green tone.  (From 0 to 63.) White balance (Green)
Press the Point 7 8buttons to adjust the blue tone.  (From 0 to 63.) White balance (Blue)
When this function is On, it automatically enhances contrast of
bright and dark part of the image.Auto grayscale
Press the Point 7 8buttons to select the Color temp. level you want
to select. (XLow, Low, Mid, or High) Color temp. 
						

							29
Computer Input
Screen Size Adjustment
This projector has a picture screen resize function, which enables you to customize the  image size.
Press the MENU button to display the On-Screen Menu.  Press
the Point 
7 8buttons to move the red frame pointer to the
Screen Menu icon.
When Digital zoom + is selected, the On-Screen Menu disappears
and the message “D. Zoom +” is displayed.  Press the SELECT
button to expand image size.  And press the Point 
e d 7 8buttons
to pan the image.  The panning function can work only when the
image is larger than screen size.
A projected image can be also expanded by pressing the D.ZOOM 
e
button on the remote control.  
1
To cancel Digital zoom +/– mode, press any button except the
D.ZOOM 
ed buttons, the SELECT and the Point buttons.
Move the red frame to the function
and press the SELECT button.Press the Point dbutton to move the red frame pointer to the
function that you want to select. Then press the SELECT button.2
Wide
Digital zoom +Note:
–This Screen Menu cannot be operated when
720p(HDTV), 1035i(HDTV) or 1080i(HDTV) is
selected on PC System Menu.  ( ☞P23 ).
–True and Digital zoom +/– cannot be selected
when 480i, 575i, 480p, 575p is selected on PC
System Menu.  (☞P23 ).
–This projector cannot display any resolution
higher  than 1280 X 1024.  If your computer’s
screen resolution is higher than 1280 X 1024,
reset the resolution to the lower before
connecting projector.
–The image data in other than SVGA (800 x 600)
is modified to fit the screen size in initial mode.
–The panning function may not operate properly
if the computer system prepared on PC Adjust
Menu is used.
Provide an image to fit the screen size.Normal
True
SCREEN MENU
When Digital zoom – is selected, the On-Screen Menu disappears
and the message “D. Zoom –” is displayed.  Press the SELECT
button to compress image size. 
A projected image can be also compressed by pressing the D.ZOOM
▼button on the remote control.  Digital zoom –
Provide image in its original size.  When the original image size is
larger than screen size ( 800 x 600 ), this projector enters “Digital
zoom +” mode automatically. 
Provide image to fit wide video aspect ratio (16 : 9) by expanding
image width uniformly.  This function can be used for providing a
squeezed video signal at 16 : 9.
Screen Menu icon
Computer Input 
						

							30
Input Source Selection ( Video, S-Video )
Menu Operation Direct Operation
Choose Video by pressing the INPUT button on the top control or the
VIDEO button on the remote control.
Before using these buttons, correct input source should be selected
through menu operation as described below.
Press the MENU button to display the On-Screen Menu.  Press
the Point 
7 8buttons to move the red frame pointer to the
Input Menu icon.
Press the Point dbutton to move the red arrow pointer to Video
and then press the SELECT button.  Source Select Menu will
appear. 
1
2
Move the red arrow pointer
to Video and press the
SELECT button.
VIDEO
Move the pointer to the
source and press the SELECT
button.
Source Select Menu (VIDEO)
INPUT MENU
INPUT button
Video
Computer
Move the pointer to the source that you want to select and then
press the SELECT button.3
When selecting Auto, the projector automatically detects
incoming video signal, and adjusts itself to optimize its
performance. The projector selects connection in the
following order:
1st S-VIDEO
2nd VIDEO
If both the S-VIDEO jack and the VIDEO jack are
connected at the same time when Auto is selected in the
Input Menu, the S-VIDEO jack will override the signal
from the VIDEO jack.Auto
When video input signal is connected to VIDEO jack,
select Video.Video
When video input signal is connected to S-VIDEO jack,
select S-Video.S-Video
Video Input
Input Menu icon