Eiki Projector Lc Sd10 User Manual

11
P-
TIMER
FREEZE
COMPUTERVIDEO
PAGESELECT
D.ZOOM
MUTE
VOLUME-MENU
NO SHOW
IMAGE
VOLUME+
KEYSTONE
AUTO PC
ON-
OFF
Overview
To insure safe operation, please observe the following
precautions :
–  Do not bend, drop the remote control, or expose
Remote Control  to moisture or heat.
–  For cleaning, use soft dry cloth.   Do not apply
benzene, thinner, splay or any chemical material.
y
30° 30°
Point the remote control toward the projector
(Receiver Window) when pressing any button.
Maximum operating range...

12
This projector uses nominal input voltages of 100-120 V or 200-240
V AC.  This projector automatically selects the correct input
voltage.  It is designed to work with single-phase power systems
having a grounded neutral conductor.  To reduce risk of electrical
shock, do not plug into any other type of power system.
Consult your authorized dealer or service station if you are not sure
of the type of power supply being in use.
Connect a projector with a peripheral equipment before turning a
projector...

13
Preparation
Positioning the Projector
–This projector is designed to project on a flat projection surface.
–The projector can be focused from 4.3’(1.3m) to 21.3’(6.5m).
–Refer to the figure below to adjust a screen size.
40”100”150”200”
169”
127”
83”
34”
A
B 21.3’ (6.5m)
16.1’ (4.9m)
10.6’ (3.2m)
4.3’ (1.3m)
Max. Zoom
Min. Zoom
A : B  =  9 : 1
Screen Size
(W x H) mm
4 : 3 aspect ratio
Zoom (min)
40”
Zoom (max)
813 x 610
4.9 (1.5m)
4.3’ (1.3m)
100”
2032 x 1524
12.5 (3.8m)
10.6’ (3.2m)
150”
3048...

14
Preparation
Remote Control Battery Installation
To insure safe operation, please observe the following precautions :
–Use (2) AAA, SUM-4 or R03 type alkaline batteries.
–Replace two batteries at the same time.
–Do not use a new battery with a used battery.
–Avoid contact with water or liquid.
–Do not expose the remote control to moisture, or heat.
–Do not drop the remote control.
–If a battery has leaked on remote control, carefully wipe case clean and install new batteries.
–Risk of explosion if...

15
S-VIDEO
COMPUTER IN 
 / COMPONENT IN/ 
COMPUTER / COMPONENTAV
AUDIO  IN
VIDEO
USB SERVICE PORT RESET
Connecting to a Computer
IBM-compatible computer or Macintosh computer (VGA / SVGA / XGA / SXGA)
Note :When connecting the cable, the power
cords of both the projector and the external
equipment should be disconnected from
AC outlet.  Turn the projector and peripheral
equipment on before the computer is
switched on.
Installation
ON ON
ON
1DIPON
OFF
23456
13 MODE (640 x 480)
16 MODE (832 x 624)
19 MODE...

16
Installation
Connecting to Video Equipment
S-VIDEO
COMPUTER IN 
 / COMPONENT IN/ 
COMPUTER / COMPONENTAV
AUDIO  IN
VIDEO
USB SERVICE PORT RESET
Video Source (example)
Video Cassette Recorder Video Disc Player
Video
Cable ✽
(RCA x 1) S-VIDEO
Cable  ✽
Note :The S-VIDEO jack has priority over the VIDEO jack under the
condition of connecting both the S-VIDEO jack and the VIDEO
jack  when selecting AUTO in the Input Menu. 
S-VIDEO
Output
Note:When connecting the cable, the power
cords of both the projector...

17
The projector can be adjusted or set via the On-Screen Menu.
Refer to the following pages regarding each adjustment and
setting procedure.
Press Point 7 8buttons to select a Menu icon to adjust.
Press Point edbuttons to select an item to adjust.
Press SELECT button to show the item data. Press Point 7 8
buttons to adjust the data. Refer to the following pages for
respective adjustment. 
How to Operate the On-Screen Menu
INPUT
MENU
SELECT
VOLUME–VOLUME+
Used to select the item.SELECT button
Used to...

18
Before Operation
Menu Bar
For  Computer  Source
PC System Menu
Used to select
computer system.
( 
☞P23 )
Image Adjust Menu
Used to adjust computer image. [Contrast / Brightness / Color
temp. / White balance (R/G/B) /Gamma / Auto grayscale]( ☞P28 )
Setting Menu
Used to change
settings of the
projector or reset
Lamp replace counter. 
( ☞P36-38 )
Sound Menu
Used to adjust
volume or
mute sound.
( ☞P21 )
Image Select Menu
Used to select  an
image level among
Standard, Real,
and Image 1 – 4.
( ☞P27 )
AV...

19
Connect the projectors AC Power Cord into an AC outlet.  The
POWER indicator flashes in a moment and then turns red.
Press POWER ON-OFF button on the top control or the remote
control.  The POWER Indicator turns green, and the cooling fans
start to operate. The starting display appears on the screen and
the count-down starts. 
2
3
Turning Off the Projector
Press the POWER ON-OFF button on the top control or the
remote control, and the message  Power off?  appears on the
screen.  
Press the POWER...

20
Press FREEZE button on the remote control to freeze the picture on-
screen.  To cancel the freeze function, press FREEZE button again or
press any other button.
Picture Freeze Function Keystone Adjustment
1Press KEYSTONE button on the remote control or select
Keystone on the Setting menu ( 
☞P36 ) to display the Keystone
dialog box.
2Correct keystone distortion by pressing Point edbuttons.
Press Point 
ebutton to reduce the upper part of image, and
press Point 
dbutton to reduce the lower part....