Eiki Projector Lc Sd10 User Manual

							MODELLC-SD10
MULTIMEDIA PROJECTOR
OWNER’S MANUAL 
						

							2
CAUTION : T O  REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR
BACK).  NO USER-SERVICEABLE PARTS
INSIDE EXCEPT LAMP REPLACEMENT.
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
THIS SYMBOL INDICATES THAT DANGEROUS
VOLTAGE CONSTITUTING A RISK OF ELECTRIC
SHOCK IS PRESENT WITHIN THIS UNIT.
THIS SYMBOL INDICATES THAT THERE ARE
IMPORTANT OPERATING AND MAINTENANCE
INSTRUCTIONS IN THE OWNERS MANUAL WITH
THIS UNIT.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
Before operating this projector, read this manual thoroughly
and operate the projector properly.  
This projector provides many convenient features and
functions.  Operating the projector properly enables you to
manage those features and maintains it in better condition for
a considerable time.
Improper operation may result in not only shortening the
product-life, but also malfunctions, fire hazard, or other
accidents.
If your projector seems to operate improperly, read this
manual again, check operations and cable connections and try
the solutions in the “Troubleshooting” section at the end of
this booklet.  If the problem still persists, contact the sales
dealer where you purchased the projector or the service
center.Safety Precaution
WARNING :  TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS APPLIANCE
TO RAIN OR MOISTURE.
–This projector produces intense light from the projection
lens.  Do not stare directly into the lens as possible.  Eye
damage could result.  Be especially careful that children do
not stare directly into the beam.
–Install the projector in a proper position.  If not, it may
result in a fire hazard.
–Take appropriate space on the top, sides and rear of the
projector cabinet for allowing air circulation and cooling the
projector.  Minimum distance should be taken.  If the
projector is to be built into a compartment or similarly
enclosed, the minimum distances must be maintained.  Do
not cover the ventilation slot on the projector.  Heat build-
up can reduce the service life of your projector, and can
also be dangerous.
–Do not put any flammable object or spray can near the
projector, hot air is exhausted from the ventilation holes.
–If the projector is not to be used for an extended time,
unplug the projector from the power outlet.
READ AND KEEP THIS OWNERS MANUAL FOR LATER
USE.
20cm
50cm 50cm
50cm
SIDE and TOPREAR
To the Owner 
						

							3
Safety Instructions
All the safety and operating instructions should be read before
the product is operated.
Read all of the instructions given here and retain them for later
use.  Unplug this projector from AC power supply before
cleaning.  Do not use liquid or aerosol cleaners.  Use a damp
cloth for cleaning.
Follow all warnings and instructions marked on the projector.
For added protection to the projector during a lightning storm,
or when it is left unattended and unused for long periods of
time, unplug it from the wall outlet.  This will prevent damage
due to lightning and power line surges.
Do not expose this unit to rain or use near water... for
example, in a wet basement, near a swimming pool, etc...
Do not use attachments not recommended by the
manufacturer as they may cause hazards.
Do not place this projector on an unstable cart, stand, or table.
The projector may fall, causing serious injury to a child or
adult, and serious damage to the projector.  Use only with a
cart or stand recommended by the manufacturer, or sold with
the projector.  Wall or shelf mounting should follow the
manufacturers instructions, and should use a mounting kit
approved by the manufacturers.
An appliance and cart combination should
be moved with care.  Quick stops,
excessive force, and uneven surfaces
may cause the appliance and cart
combination to overturn.
Slots and openings in the back and bottom of the cabinet are
provided for ventilation, to insure reliable operation of the
equipment and to protect it from overheating.
The openings should never be covered with cloth or other
materials, and the bottom opening should not be blocked by
placing the projector on a bed, sofa, rug, or other similar
surface.  This projector should never be placed near or over a
radiator or heat register.
This projector should not be placed in a built-in installation
such as a book case unless proper ventilation is provided.
Never push objects of any kind into this projector through
cabinet slots as they may touch dangerous voltage points or
short out parts that could result in a fire or electric shock.
Never spill liquid of any kind on the projector.This projector should be operated only from the type of power
source indicated on the marking label.  If you are not sure of
the type of power supplied, consult your authorized dealer or
local power company.
Do not overload wall outlets and extension cords as this can
result in fire or electric shock.  Do not allow anything to rest
on the power cord.  Do not locate this projector where the
cord may be damaged by persons walking on it.
Do not attempt to service this projector yourself as opening or
removing covers may expose you to dangerous voltage or
other hazards.  Refer all servicing to qualified service
personnel.
Unplug this projector from wall outlet and refer servicing to
qualified service personnel under the following conditions:
a. When the power cord or plug is damaged or frayed.
b. If liquid has been spilled into the projector.
c. If the projector has been exposed to rain or water.
d. If the projector does not operate normally by following the
operating instructions.  Adjust only those controls that are
covered by the operating instructions as improper
adjustment of other controls may result in damage and will
often require extensive work by a qualified technician to
restore the projector to normal operation.
e. If the projector has been dropped or the cabinet has been
damaged.
f.When the projector exhibits a distinct change in
performance-this indicates a need for service.
When replacement parts are required, be sure the service
technician has used replacement parts specified by the
manufacturer that have the same characteristics as the
original part.  Unauthorized substitutions may result in fire,
electric shock, or injury to persons.
Upon completion of any service or repairs to this projector,
ask the service technician to perform routine safety checks to
determine that the projector is in safe operating condition.
Voor de klanten in Nederland
Bij dit product zijn batterijen
geleverd.  
Wanneer deze leeg zijn, moet u
ze niet weggooien maar
inleveren als KCA.
Do not install the projector near the ventilation duct of air-
conditioning equipment. 
						

							4
Safety Instruction
CAUTION IN CARRYING OR TRANSPORTING
THE PROJECTOR
–Do not drop or bump a projector, otherwise damages or
malfunctions may result.
–When carrying a projector, use a suitable carrying case.
–Do not transport a projector by using a courier or transport
service in an unsuitable transport case.  This may cause
damage to a projector.  To transport a projector through a
courier or transport service, consult your dealer for best
way.
Moving the Projector
CAUTION
Carrying Bag (supplied) is intended for protection from dust
and scratches on the surface of a cabinet, and it is not
designed to protect an appliance from external forces.  Do not
transport a projector through a courier or transport services
with this bag, otherwise the projector can be damaged.  When
handling a projector, do not drop, bump, subject it to strong
forces or put other things on the cabinet.  
When moving the projector, replace the Lens Cover and
retract Adjustable Feet to prevent damage to the lens and
cabinet.
When the  projector is not in use for an extended period,  put
it into the case (carrying bag) supplied with the projector. 
20˚
20˚Do not tilt the projector more than 20
degrees to either side.
Do not point the projector up to pro-
ject an image. 
Do not point the projector down to
project an image. 
Do not put the projector on either
side to project an image. 
Install the projector properly. Improper Installation may reduce
the lamp lifetime and cause a fire hazard.
NO UPWARD
NO DOWNWARD
NO SIDEWARD Installing the Projector in Proper Position
Openings in the cabinet are provided for ventilation and to
ensure reliable operation of the product and to protect it from
overheating, and these openings must not be blocked or
covered. 
CAUTION
Hot air is exhausted from the exhaust vent.  When using or
installing the projector, the following precautions should be
taken. 
–  Do not put any flammable objects near the vent.
– Keep the exhaust vent at least 3’(1m) away from any
objects.
–  Do not touch a peripheral part of the exhaust vent, espe-
cially screws and metallic part.  This area will become hot
while the projector is being used.
–  Do not put anything on the cabinet.  The materials put on
the cabinet will not only get damaged but also cause fire
hazard by heat.
Cooling fans are provided to cool down the projector.  This
projector monitors internal temperature and control the run-
ning speed of the cooling fans.  
Air Circulation
Air Intake Vent
Exhaust Vent
(Hot air exhaust) 
						

							5
Compliance
The AC Power Cord supplied with this projector meets the requirement for use in the country you purchased it.  
AC Power Cord for the United States and Canada :
AC Power Cord used in the United States and Canada is listed by the Underwriters
Laboratories (UL) and certified by the Canadian Standard Association (CSA).
AC Power Cord has a grounding-type AC line plug.  This is a safety feature to be sure that the
plug will fit into the power outlet.  Do not try to defeat this safety feature.  Should you be
unable to insert the plug into the outlet, contact your electrician.
GROUND
THE SOCKET-OUTLET SHOULD BE INSTALLED NEAR THE EQUIPMENT AND EASILY ACCESSIBLE.
AC Power Cord Requirement
Federal Communication Commission Notice
Note : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part
15 of the FCC Rules.  These limits are designed to provide reasonable protection against harmful interference in a
residential installation.  This equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications.  However, there is
no guarantee that interference will not occur in a particular installation.  If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures :
–Reorient or relocate the receiving  antenna.
–Increase the separation between the equipment and receiver.
–Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
–Consult the dealer or an experienced radio/TV technician for help.
Use of shielded cable is required to comply with class B limits in Subpart B of Part 15 of FCC Rules.
Do not make any changes or modifications to the equipment unless otherwise specified in the instructions.  If such
changes or modifications should be made, you could be required to stop operation of the equipment.
Model Number  : LC-SD10 Model Number : TGX0043-011010 (1AV4U20B69000)
Trade Name  : EIKI IR Presentation Remote Receiver for Projector
Responsible party  : EIKI International Inc. Trade Name : HOSIDEN
Address  : 30251 Esperanza, Rancho Santa Margarita, Responsible Party : Hosiden America Corp.
CA 92688-2132 Address : 120 East State Parkway, Schaumburg, IL, 60173
Telephone No.  : (800)242-3454 (949-457-0200) Telephone No. : (847)885-8870 
						

							6
Table of Contents
TRADEMARKS
•Apple, Macintosh, and PowerBook are trademarks or registered trademarks of Apple Computer,Inc.
•IBM, VGA, XGA, and PS/2 are trademarks or registered trademarks of International Business Machines, Inc.
•Windows and PowerPoint are registered trademarks of Microsoft Corporation.
•Each name of corporations or products in the owners manual is a trademark or a registered trademark of its respective
corporation.
To the Owner  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Safety Instructions  . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Compliance  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Table of Contents  . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Features and Design  . . . . . . . . . . . . . . . . . . . . . . . . . .7
Overview  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Front  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Back  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Bottom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Top panel  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Terminals  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Remote Control  . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Operating Range  . . . . . . . . . . . . . . . . . . . . . . . . .11
Preparation  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Connecting the AC Power Cord  . . . . . . . . . . . . . . .12
Positioning the Projector  . . . . . . . . . . . . . . . . . . . . .13
Adjustable Feet  . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Remote Control Battery Installation  . . . . . . . . . . . .14
Attaching the Lens Cover  . . . . . . . . . . . . . . . . . . . .14
Installation  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Connecting to a Computer  . . . . . . . . . . . . . . . . . . .15
Connecting to Video Equipment  . . . . . . . . . . . . . . .16
Before Operation  . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
How to Operate the On-Screen Menu  . . . . . . . . . .17
Menu Bar  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Basic Operation  . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Turning On the Projector  . . . . . . . . . . . . . . . . . . . . .19
Turning Off the Projector  . . . . . . . . . . . . . . . . . . . . .19
Adjusting the Screen  . . . . . . . . . . . . . . . . . . . . . . . .20
Zoom Adjustment  . . . . . . . . . . . . . . . . . . . . . . . .20
Focus Adjustment  . . . . . . . . . . . . . . . . . . . . . . . .20
Keystone Adjustment  . . . . . . . . . . . . . . . . . . . . .20
Picture Freeze Function  . . . . . . . . . . . . . . . . . . .20
No Show Function . . . . . . . . . . . . . . . . . . . . . . . .21
P-Timer Function  . . . . . . . . . . . . . . . . . . . . . . . . .21
Sound Adjustment  . . . . . . . . . . . . . . . . . . . . . . . . . .21Computer Input  . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Input Source Selection  . . . . . . . . . . . . . . . . . . . . . .22
Computer System Selection  . . . . . . . . . . . . . . . . . .23
PC Adjustment  . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
Auto PC Adjustment  . . . . . . . . . . . . . . . . . . . . . .24
Manual PC Adjustment  . . . . . . . . . . . . . . . . . . . .25
Image Level Selection  . . . . . . . . . . . . . . . . . . . . . . .27
Image Level Adjustment  . . . . . . . . . . . . . . . . . . . . .28
Screen SIze Adjustment  . . . . . . . . . . . . . . . . . . . . .29
Video Input  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
Input Source Selection ( 
Video, S-Video) . . . . . . . . . .30
Input Source Selection ( 
Component, RGB Scart 21-pin) . .31
Video System Selection . . . . . . . . . . . . . . . . . . . . . .32
Image Level Selection  . . . . . . . . . . . . . . . . . . . . . . .33
Image Level Adjustment  . . . . . . . . . . . . . . . . . . . . .34
Screen Size Adjustment  . . . . . . . . . . . . . . . . . . . . .35
Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
Setting Menu  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
Using the Presentation Remote Control  . . . . . . . . .39
Presentation Remote Control  . . . . . . . . . . . . . . . . .39
Installation  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
Maintenance  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
Lamp Replacement  . . . . . . . . . . . . . . . . . . . . . . . . .40
Lamp Replace  . . . . . . . . . . . . . . . . . . . . . . . . . . .40
Lamp Replace Counter  . . . . . . . . . . . . . . . . . . . .41
Warning Indicator  . . . . . . . . . . . . . . . . . . . . . . . . . .42
Air Filter   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
Cleaning the Projection Lens  . . . . . . . . . . . . . . . . . .43
Appendix  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
Troubleshooting  . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
Indicators and Projector Condition . . . . . . . . . . . . . .46
Menu Tree  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
Compatible Computer Specifications  . . . . . . . . . . .49
Technical Specifications  . . . . . . . . . . . . . . . . . . . . .50
Configuration of Terminals  . . . . . . . . . . . . . . . . . . .51
Optional Parts  . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51 
						

							7
Features and Design
LC-SD10 is designed with the most advanced technology for portability, durability, and ease of use.  This projector utilizes
built-in multimedia features, a palette of 16.77 million colors, and matrix liquid crystal display (LCD) technology.
Outstanding Compatibility 
This projector widely accepts various video and
computer input signals including;
–Computers
IBM-compatible or Macintosh computer up to
1280 x 1024 resolution.
–6 Color Systems
NTSC, PAL, SECAM, NTSC 4.43, PAL-M or PAL-N 
color system can be connected.
– Component Video
Component video signal, such as a DVD player
output, high definition TV signals including 480i,
480p, 575i, 575p, 720p, 1035i or 1080i, can be
connected.
–  S-Video
S-Video signal, such as a S-VHS VCR output signal,
can be connected.
– RGB Scart
RGB Scart signal can be connected.
Superb Image Quality
Supports 800 x 600 dots resolution for computer input.
Resolution from a computer between SVGA (800 x 600)
and SXGA (1280 x 1024) is precisely compressed into
800 x 600 dots. 
Multi-Scan System
This projector has Multi-Scan System to conform to
almost all computer output signals quickly.  No need for
troublesome manual adjustment of frequency and other
settings. ( 
☞P23 )
Digital Keystone Adjustment
Positioning height of the projector may result in distorted
image being displayed in a trapezoid shape.  Keystone
Adjustment solves this problem by digitally altering
projection to produce undistorted images. ( 
☞P20, P36 )
Multi-language Menu Display
Operation menu is displayed in; English, German,
French, Italian, Spanish, Portuguese, Dutch, Swedish,
Russian, Chinese, Korean or Japanese. ( 
☞P36 )
Auto PC Adjustment
Incoming computer signals are recognized and the best
adjustment is automatically set by Auto PC Adjustment.
No complicated setup is necessary and projection is
always precise. ( 
☞P24 )
Digital Zoom (for Computer)
Digital Zoom function expands (to approx. 16 times of
screen size) or compress the image size, allowing you to
focus on crucial information at a presentation. ( 
☞P29 )
Greater Mobility
Extremely compact in size and weight.  It is designed to
be carried and work anywhere you wish to use.
Power Management
Provided to reduce power consumption and maintain the
lamp life. ( 
☞P37 )
Presentation Remote Control 
The provided Presentation Remote Control can be used
as a wireless mouse to control the mouse cursor on the
computer screen. This is extremely useful while giving
presentations.  ( 
☞P39 )
User Logo
A projected image can be captured and used for the
starting display of the projector. ( 
☞ Capture function P36 )
You can also display the captured image in an interval
during your presentation instead of blackout image.  
( 
☞ No Show function  P21 )
Interlace Progressive Conversion
HIgh-quality picture is available with this technology
which converts interlace signal  into progressive signal. 
( 
☞P35 )
Key Lock Function
Provided to lock the operation of the projector. This
function protects the projector from being tampered
with by third persons.  ( 
☞P38 ) 
						

							8
qZoom Lever( ☞P20 )
wInfrared Remote Receiver( 
☞P11 )
eFocus Ring( 
☞P20 )
rProjection Lens( 
☞P43 )
tLens Cover
yAir Intake Vent( 
☞P43 )
uExhaust Vent
qAir Intake Vent ( ☞P43 )
wTerminals and Connectors( 
☞P10, 15,16 )
ePower Cord Connector( 
☞P12 )
rExhaust Vent 
qAir Filters( ☞P43 )
wAir Intake Vents( 
☞P43 )
eAdjustable Feet( 
☞P14 )
e
w
q
u
y
t
r
i
e
w
qt
r
y
CAUTION
Hot air is exhausted from the exhaust vents.
When using or installing the projector, the follow-
ing precautions should be taken. 
– Do not put any flammable objects near these
vents.
– Keep front grills at least 3’(1m) away from any
objects, especially heat-sensitive objects.
– Do not touch this area, especially screws and
metallic part.  This area will become hot while
the projector is being used.
This projector detects internal temperature and
will automatically adjust the running speed of the
cooling fans.
Bottom
q
e
w
Back Front
Overview
CAUTION
Hot air is exhausted from the exhaust vent.  Do
not put heat-sensitive objects near this side.
iSpeaker
tAir Intake Vent( ☞P43 )
yTop Controls and Indicators( 
☞P9 )
CAUTION
Hot air is exhausted from the exhaust vent.  Do
not put heat-sensitive objects near this side. 
						

							9
Overview
Top panel
POWERLAMP
REPLACE WARNING
INPUT
MENU ON - OFF
SELECTVOLUME–VOLUME+
e
w
q
uy
t
r
i
iPOWER indicator
Flashes red until the projector gets ready to be turned 
on.  It turns red when the projector is in the stand-by  
mode.  It remains green while the projector is in 
operation.  ( 
☞P19,37,42 )
qPOWER ON-OFF button 
Turns the projector on or off.  ( 
☞P19 )
wSELECT button
–Executes the selected item. ( 
☞P17 )
–Expands / compresses the image in Digital Zoom
mode. ( 
☞P29 )
r MENU button
Opens or closes the On-Screen Menu. ( 
☞P17 )
t INPUT button
Selects input source.   ( 
☞P22,P30 )
ePoint e
ed
d
7 8( VOLUME + / –
) buttons
– Select an item or adjust  value in the On-Screen Menu. 
( 
☞P17 ) 
– Pan the image in DIGITAL ZOOM +/– mode. ( 
☞P29 )
– Adjust volume level. (Point 
7 8buttons)  ( ☞P21 )
yLAMP REPLACE indicator
Turns yellow when the life of the projection lamp draws 
to an end.  ( 
☞P40 )
uWARNING indicator
Lights red when the projector is in the abnormal 
condition.  This indicator also flashes red when the 
internal projector temperature goes up over the 
operating range.  ( 
☞P42 ) 
						

							10
S-VIDEO
COMPUTER IN 
 / COMPONENT IN/ 
COMPUTER / COMPONENTAV
AUDIO  IN
VIDEO
USB SERVICE PORT RESET
✽RESET button
A microprocessor included in the projector may occasionally
malfunction and need to be reset. If necessary, press this
button with a sharp tool to restart the unit. Do not use it
excessively. 
yAUDIO IN  COMPUTER/ COMPONENT
Connect audio output from a computer or component to 
this jack. ( 
☞P15, P16 )
Terminals
Overview
ewq✽
utr
uCOMPUTER IN / COMPONENT IN
Connect computer output, component output or RGBScart 21-pin video output to this connector. ( ☞P15,
P16 )
q VIDEO
Connect the composite video output from video
equipment. ( 
☞P16 )
w S-VIDEO
Connect S-video output from video equipment. ( 
☞P16 )
e SERVICE PORT
This jack is used to service this projector. 
r USB
Connect the USB port of your computer to this port
when you wish to use the PAGE 
ed buttons on the
remote control to scroll back and forth pages on the
screen of the connected computer.
( ☞ P15, P38 )
tAUDIO IN  AV
Connect audio output from video equipment. ( 
☞P16 )
y