Eiki Projector Lc Sd10 User Manual

							21
Basic Operation
Message disappears after 4 seconds.
Press P-Timer button on the remote control.  The timer display “00 :
00” appears on the screen and the timer starts to count time (00 : 00
~ 59 : 59).  
To stop P-Timer display, press the P-TIMER button.  And then, press
P-TIMER button again to cancel P-Timer function.
1
2
Press MENU button to display the On-Screen Menu. Press Point
78buttons to move the red frame pointer to SOUND Menu
icon.  Volume
Press VOLUME (+/–) button on the remote control or on the top
control to adjust volume.  The volume dialog box appears on the
screen for a few seconds.
VOLUME (+) button to increase volume, and VOLUME (–) button  for
decreasing.
Mute
Press MUTE button on the remote control to cut off sound.  To
restore sound to its previous level, press MUTE button again or press
Volume (+/–).
To increase volume, press Point 8button, and press Point 7 button to
decrease volume. 
Press Point 78 buttons to mute sound. Dialog box display is changed
to “On” and sound is muted.  To restore sound to its previous level,
press Point
78buttons again.
Press Point dbutton to move the red frame pointer to the item
that you want to select, and then press SELECT button.
Indicates approximate
level of volume.
Close Sound Menu.
Direct Operation
Menu Operation
Volume
Mute
Indicates approximate
level of volume.
The display disappears after 4 seconds.  
SOUND MENU
Sound Menu icon
Sound Adjustment
P-Timer Function No Show Function
Press MUTE button to set
Mute function On or Off.
Press NO SHOW button on the remote control to black out the image.
To restore to normal, press the NO SHOW button again or press any
other button.  When a projected image is captured and set as “User”
in the Logo item in the Setting menu ( 
☞ P36 ), the screen changes
each time you press the NO SHOW button as follows :
black out ➜the captured image ➜normal ➜...... 
						

							22
Menu Operation Direct Operation
Choose Computer by pressing INPUT button on the top control or
COMPUTER button on the remote control.
Before using these buttons, correct input source should be selected
through menu operation as described below.
Press the MENU button to display the On-Screen Menu. Press
Point 
7 8buttons to move the red frame pointer to INPUT
Menu icon.
Press Point dbutton to move the red arrow pointer to
Computer and then press SELECT button. The Source Select
Menu will appear. 
1
2
INPUT button
Computer
Video
INPUT MENU
Input Menu icon
Input Source Selection
Computer Input
Move the pointer to the correct input source and press SELECT
button. 3
When the input source is coming from a computer
through the COMPUTER IN / COMPONENT IN
terminal, select RGB. RGB 
RGB (Scart)
Component ☞ Selecting Input Source (Component / RGB-Scart
21-pin )  P31. 
Move the pointer (red
arrow) to Computer and
press SELECT button.
Move the pointer to RGB and
press the SELECT button.
Source Select Menu
☞ Selecting Input Source (Component / RGB-Scart
21-pin )  P31.  
						

							23
Computer Input
Computer System Selection
This projector automatically tunes to various types of computers based on VGA, SVGA, XGA or SXGA with its Multi-scan
system and Auto PC Adjustment.  If Computer is selected as a signal source, this projector automatically detects the signal
format and tunes to project a proper image without any additional setting.  (Signal formats provided in this projector is
shown on page 49 )
When projector cannot recognize connected signal as PC
system provided in this projector, Auto PC Adjustment
function operates to adjust projector and the message
“Auto” is displayed on System Menu icon.  (
☞P24.)
When image is not provided properly, manual adjustment
is required.  (
☞P25 - 26 )
There is no signal input from computer.  Make sure the
connection of computer and a projector is set correctly.  
(
☞ Troubleshooting P44 )
Auto
-----
System Menu icon
Displays system being
selected.
PC SYSTEM MENU
Selecting Computer System Manually
SYSTEM Menu icon 
Displays system being selected.
The systems on this dialog box
can be selected.
Press MENU button to display the On-Screen Menu. Press Point
7 8buttons to move the red frame pointer to PC SYSTEM
Menu icon.
Press Point dbutton to move the red arrow pointer to the
system that you want to set, and then press 
SELECT button.  
1
2
PC SYSTEM MENU
Custom Mode (1–5) set in PC
Adjust Menu.  ( ☞P24-26 )
PC system can be also selected manually.
Note :The projector may display one of the following messages.
User preset adjustment in Computer Adjustment.
Adjustment data can be stored in Mode 1 - 5.  ( 
☞P25-
26 )  Mode 1
Computer systems provided in the projector.  The
projector chooses a proper system and displays it.  SVGA 1
*Mode 1 and SVGA 1 are examples.   
						

							24
Computer Input
Auto PC Adjustment
Auto PC Adjustment function is provided to automatically conform Fine sync, Total dots and Picture Position to your
computer.  This function can be operated as follows.
Press the MENU button to display the On-Screen Menu.  Press
Point 
7 8button to move the red frame pointer to PC Adjust
Menu icon.1
2Press the Point dbutton to move the red frame pointer to Auto
PC Adj. icon and then press the SELECT button twice.
This Auto PC Adjustment can be also executed by pressing the
Auto PC button on the remote control.Move the red frame pointer to Auto PC
Adj. icon and press SELECT button.
PC ADJUST MENU Auto PC Adj.
PC Adjust Menu icon
To store adjustment parameters :
Adjustment parameters from Auto PC Adjustment can be memorized
in this projector.  Once parameters are memorized, the setting can be
done just by selecting Mode in PC System Menu ( 
☞ P23 ).  Refer to
 Store  of Manual PC Adjustment section ( 
☞ 26 ).
Note :
–  Fine sync, Total dots and Picture Position of some computers can not be
fully adjusted with this Auto PC Adjustment function.  When the image is
not provided properly through this function, manual adjustments are
required. ( 
☞P25 )
– Auto PC Adjustment function cannot be operated when “480p”, “575p”,
“480i”, “575i”, “720p (HDTV),” “1035i (HDTV)” or “1080i (HDTV)” is
selected on PC SYSTEM Menu ( 
☞ P23).
PC Adjustment 
						

							25
Computer Input
Manual PC Adjustment
Some computers employ special signal formats which may not be tuned by Multi-Scan system of this projector.  In this
case, the projector cannot reproduce a proper image and the image may be recognized as a flickering picture, a non-
synchronized picture, a non-centered picture or a skewed picture.
The Manual PC Adjustment function allows you to precisely adjust several parameters to match those special signal
formats. You can store those adjusted parameters in the 5 independent memory areas, enabling you to call up whenever
you need.
Press MENU button to display the On-Screen Menu. Press Point
7 8buttons to move the red frame pointer to PC Adjust Menu
icon.1
2Press Point dbutton to move the red frame pointer to the item
that you want to adjust and then press SELECT button.
Adjustment dialog box will appear.  Press Point 
7 8buttons to
adjust value.
Move the red frame pointer to the item
and press SELECT button.
PC ADJUST MENU
PC Adjust Menu icon
Adjusts an image as necessary to eliminate flicker from the display.
Press Point 
7 8buttons to adjust value.(From 0 to 31.) Fine sync
Adjusts the number of total dots in one horizontal period.  Press
Point 
7 8buttons and adjust number to match your PC image. Total dots
Adjusts horizontal picture position.  Press Point 7 8buttons to
adjust the position.Horizontal
Adjusts vertical picture position.  Press Point 7 8buttons to adjust
the position.Vertical
Press SELECT button to show the information of computer selected.Current mode
Adjusts clamp level.  When the image has a dark bar(s), try this
adjustment.Clamp
Press SELECT button at this icon
to adjust “Clamp,” “Display area
(H/V)” or set “Full screen.”
Press Point 7 8buttons to
adjust the value.
Shows status
(Stored / Free) of the
selected Mode. Selected Mode
Press SELECT button at
Current mode icon to show
the information of computer
connected.
Current mode 
						

							26
Computer Input
Note : 
Display area, Display area (H/V) and Full screen cannot be adjusted when
“480p”, “575p”, “480i”, “575i”, “720i (HDTV)” , “1035i (HDTV)” or “1080i
(HDTV)” is selected on PC SYSTEM Menu    ( 
☞P23 ).
Selects area displayed with this projector.  Select the resolution at
Display area dialog box.Display area
Adjustment of horizontal area displayed with this projector.  Press
Point 
7 8buttons to decrease/increase value to match the
resolution of image. Then press the SELECT button.Display area H
Adjustment of vertical area displayed with this projector.  Press Point
7 8buttons to decrease / increase value to match the resolution of
image. Then press the SELECT button.Display area V
Press Point 7 8buttons to switch Full screen function to  “On” or
“Off.”  Set “On” to resize the image with 4 x 3 aspect ratio to fit the
screen. Full screen
Reset
Store
Closes PC Adjust Menu.
Quit
To store adjustment parameters, move the red frame pointer to
Store icon and then press SELECT button.  Move the red arrow
pointer to any of Mode 1 to 5 that you want to store to and then
press SELECT button.
Reset all adjust parameters on adjustment dialog box to previous
figure.
Mode free
Vacant Mode
Close this dialog box.
To store adjustment data To clear adjustment data
To clear adjustment parameters previously set, move the red frame
pointer to Mode free icon and then SELECT button.  Move the red
arrow pointer to the Mode that you want to clear and then press
SELECT button.
Press SELECT button at Display
area icon to show the Display
area dialog box.
Display area
This Mode has parameters being stored.
Shows values of “Total
dots,” “Horizontal,”
“Vertical,” “Display area H,”
and “Display area V.” 
						

							27
Computer Input
Menu Operation
Press MENU button to display the On-Screen Menu. Press Point
7 8button to move the red frame pointer to Image Select Menu
icon.1
2Press Point dbutton to move the red frame pointer to the level
that you want to set and then press SELECT button.Move the red frame pointer to the
level and press SELECT button.
The level being selected.
IMAGE SELECT MENU
Normal picture adjustment preset on this projector.Standard
Picture adjustment improved in reproduction of halftones.  This
adjustment is suitable for providing better image in brighter place.Real
User preset picture adjustment in Image Adjust Menu ( ☞P28 ). Image 1~4
Image Select
Menu icon
Direct Operation
Select image level among Standard, Real, Image 1, Image 2, Image 3
and Image 4 by pressing IMAGE button on the remote control.IMAGE button
Standard
Real
Image 1
Image 2
Image 3
Image 4
Normal picture adjustment preset on this projector.  
Picture adjustment improved in reproduction of halftones.  This
adjustment is suitable for providing better image in brighter place.
User preset picture adjustment in Image Adjust Menu ( ☞ P28 ). Standard
Real
Image 1~4
Image Level Selection 
						

							28
Image Level Menu
Move the red frame
pointer to any of
Image 1 to 4 where
you want to set  and
then press SELECT
button.
Reset all adjustment to previous figure.
Reset
Store
Closes Image Menu.
Quit
To store manually preset image, move the red frame pointer to Store
icon and press SELECT button.  The Image Level Menu will appear.
Move the red frame pointer to the Image 1 to 4 where you want to
set and then press SELECT button.
Computer Input
Press Point 7 8buttons to
adjust value.
Press MENU button to display the On-Screen Menu.  Press
Point 
7 8buttons to move the red frame pointer to Image
Adjust Menu icon.1
2Press Point dbutton to move the red frame pointer to the item
that you want to adjust. and then press SELECT button.  The
level of each item is displayed.  Adjust each level by pressing
Point 
7 8buttons.Move the red frame pointer to
the item to be selected and
then press SELECT button.
IMAGE ADJUST MENU
Image Level Adjustment
Store icon
Press SELECT button at this icon to
store the adjustment.
Image Adjust
Menu icon
Selected Image level
Press Point 7 8 buttons to adjust the image contrast. (From 0 to 63.)
Press Point 7 8buttons to adjust the image brightness.  (From 0 to 63.) Contrast
Brightness
Press Point 7 8buttons to obtain better balance of contrast. (From 0
to 15.)Gamma
Press Point 7 8buttons to adjust the red tone.  (From 0 to 63.) White balance (Red)
Press Point 7 8buttons to adjust the green tone.  (From 0 to 63.) White balance (Green)
Press Point 7 8buttons to lighten the blue tone.  (From 0 to 63.) White balance (Blue)
When this function is ON, it automatically enhances contrast of
bright and dark part of image.Auto grayscale
Press Point 7 8buttons to select the Color temp. level that you
want to select. (XLow, Low, Mid, or High) Color temp. 
						

							29
Computer Input
Screen Size Adjustment
This projector has a picture screen resize function, which enables you to display the desirable image size.
Press MENU button to display the On-Screen Menu.  Press
Point 
7 8buttons to move the red frame pointer to Screen
Menu icon.
When Digital zoom + is selected, the On-Screen Menu disappears
and the message “D. Zoom +” is displayed.  Press SELECT button
to expand image size.  And press Point 
ed7 8buttons to pan the
image.  The panning function can work only when the image is larger
than screen size.
A projected image can be also expanded by pressing D.ZOOM 
e
button on the remote control.  
1
To cancel Digital Zoom +/– mode, press any button except D.ZOOM
ed, SELECT and Point buttons.
Move the red frame to the function
and press SELECT button.
Press Point dbutton to move the red frame pointer to the
function that you want to select. Then press SELECT button.2
Wide
Digital zoom +Note:
–This Screen Menu cannot be operated when
“720p (HDTV)”, “1035i (HDTV)” or “1080i
(HDTV)” is selected on PC System Menu. ( 
☞ P23 ).
–True and Digital zoom +/– cannot be selected
when “480i ”,  575i ,  480p ,  575p   is
selected on PC System Menu  (
☞ P23 ).
–This projector cannot display any resolution
higher  than 1280 X 1024.  If your computer’s
screen resolution is higher than 1280 X 1024,
reset the resolution to the lower before
connecting projector.
–The image data in other than SVGA (800 x 600)
is modified to fit the screen size in initial mode.
–The panning function may not operate properly
if the computer system prepared on PC Adjust
Menu is used.
Provides an image to fit screen size.Normal
True
SCREEN MENU
When Digital zoom – is selected, the On-Screen Menu disappears
and the message “D. Zoom –” is displayed.  Press SELECT button
to compress image size. 
A projected image can be also compressed by pressing D.ZOOM ▼
button on the remote control.  Digital zoom –
Provides image in its original size.  When the original image size is
larger than screen size ( 800 x 600 ), this projector enters “Digital
zoom +” mode automatically. 
Provides image to fit wide video aspect ratio (16 : 9) by expanding
image width uniformly.  This function can be used for providing a
squeezed video signal at 16 : 9.
Screen Menu 
						

							30
Input Source Selection ( Video, S-Video )
Menu Operation Direct Operation
Choose Video by pressing INPUT button on the top control or VIDEO
button on the remote control.
Before using these buttons, correct input source should be selected
through menu operation as described below.
Press MENU button to display the On-Screen Menu.  Press
Point 
7 8buttons to move the red frame pointer to INPUT
Menu icon.
Press Point dbutton to move the red arrow pointer to Video
and then press SELECT button.  Source Select Menu will
appear. 
1
2
Move the red arrow
pointer to Video and
press SELECT button.
VIDEO
Move the pointer to the
source and press SELECT
button.
Source Select Menu (VIDEO)
INPUT MENU
INPUT button
Video
Computer
Move the pointer to the source that you want to select and then
press SELECT button.3
When selecting Auto, the projector automatically detects
incoming video signal, and adjusts itself to optimize its
performance. The projector selects connection in the
following order:
1st S-VIDEO
2nd VIDEO
The S-VIDEO has priority over the VIDEOAuto
When video input signal is connected to VIDEO jack,
select Video.Video
When video input signal is connected to S-VIDEO jack,
select S-Video.S-Video
Video Input