Eiki Projector Lc Sb22 User Manual

							51
Maintenance and Cleaning
Disconnect the AC power cord before cleaning.
When the projector is not in use, replace the lens
cover.
1
3
2
Follow these steps to clean the projection lens.
Cleaning the Projector Cabinet
Disconnect the AC power cord before cleaning.1
Softly wipe the projector body with a soft, dry cleaning
cloth.  When it is heavily soiled, use a small amount of
mild detergent and finish with a soft, dry cleaning
cloth.  Avoid using an excessive amount of cleaner.
Abrasive cleaners, solvents, or other harsh chemicals
might scratch the surface.2
Follow these steps to clean the projector cabinet.
When the projector is not in use, put the projector in
an appropriate carrying case to protect it from dust and
scratches.3
Softly wipe the projection lens with a cleaning cloth
that contains a small amount of non-abrasive camera
lens cleaner, or use lens cleaning paper or a
commercially available air blower to clean the lens.
Avoid using an excessive amount of cleaner.  Abrasive
cleaners, solvents, or other harsh chemicals might
scratch the surface.
Cleaning the Projection Lens
Maintenance & Cleaning 
						

							52
Maintenance and Cleaning
When the life of the projection lamp of this projector draws
to an end, the LAMP REPLACE indicator emits a yellow
light.  If this indicator lights yellow, replace the lamp with a
new one promptly.
Follow these steps to replace the lamp.
Lamp
ORDER REPLACEMENT LAMP
Replacement lamp can be ordered through your dealer.  When ordering a projection lamp, give the following
information to the dealer.
●
Model No. of your projector :  LC-SB22
●Replacement Lamp Type No. :  POA-LMP90
(Service Parts No. 610 323 0726)
For continued safety, replace with a lamp of the
same type.  Do not drop a lamp or touch a glass
bulb! The glass can shatter and may cause injury.Allow a projector to cool, for at least 45 minutes
before you open the Lamp cover.  The inside of
the projector can become very hot.
Top Control
CAUTION
Screw
Turn off the projector and disconnect the AC power
cord.  Allow the projector to cool for at least 45
minutes.
Remove 2 screws of the lamp with a screwdriver and
pull out the lamp by grasping the handle.
1
3
Replace the lamp with a new one and tighten the 2
screws back into position.  Make sure that the lamp is
set properly.  Replace the lamp cover and tighten the
screw.4
Remove the screw with a screwdriver, and remove
the lamp cover.2
Connect the AC power cord to the projector and turn
on the projector.
6Reset the lamp replacement counter.
See “Lamp Replacement Counter” on the next page .
5
Lamp Replacement
Handle Screw
CAUTION
ON - OFF
POWERKEYSTONE
INPUTWARNINGLAMP REPLACEMENU
- VOLUME
+ VOLUME
SELECT
ScrewLamp Cover
WARNING:
TURN OFF THE UV LAMP BEFORE
OPENING THE LAMP COVER
This indicator is yellow when
the life of the projection lamp
draws to an end.   
						

							53
Maintenance and Cleaning
Be sure to reset the Lamp replacement counter after the lamp is replaced.  When the Lamp replacement
counter is reset, the LAMP REPLACE indicator stops lighting.
Turn the projector on, press the MENU button to
display the On-Screen Menu.  Press the Point
7 8
buttons to move the red framed pointer to the Setting
Menu icon.
Press the Point edbuttons to move the red framed
pointer to the Lamp counter function and then press
the SELECT button.  The first dialog box appears and
shows the total accumulated time of the lamp usage
and the reset option.  If you select Reset, a Lamp
replacement counter Reset? message will appear.
Select [Yes] to continue.
1
2
Another confirmation dialog box will appear, select
[Yes] to reset the Lamp replacement counter.3
This projector uses a high-pressure lamp which must be handled carefully and properly.  
Improper handling may result in accidents, injury, or create a fire hazard.
●Lamp life may differ from lamp to lamp and according to the environment of use.  There is no
guarantee of the same life for each lamp.  Some lamps may fail or terminate their life in a shorter
period of time than other similar lamps.
●If the projector indicates that the lamp should be replaced, i.e., if the LAMP REPLACE indicator lights
up, replace the lamp with a new one IMMEDIATELY after the projector has cooled down.  
( Follow carefully the instructions in the Lamp Replacement section of this manual.  )  Continuous use
of the lamp with the LAMP REPLACE indicator lighted may increase the risk of lamp explosion.  
●A Lamp may explode as a result of vibration, shock or degradation as a result of hours of use as its
lifetime draws to an end.  Risk of explosion may differ according to the environment or conditions in
which the projector and lamp are being used.
IF A LAMP EXPLODES, THE FOLLOWING SAFETY PRECAUTIONS SHOULD BE TAKEN.
If a lamp explodes, disconnect the projector’s AC plug from the AC outlet immediately.  Contact an
authorized service station for a checkup of the unit and replacement of the lamp.  Additionally, check
carefully to ensure that there are no broken shards or pieces of glass around the projector or coming out
from the cooling air circulation holes.  Any broken shards found should be cleaned up carefully.  No one
should check the inside of the projector except those who are authorized trained technicians and who are
familiar with projector service.  Inappropriate attempts to service the unit by anyone, especially those
who are not appropriately trained to do so, may result in an accident or injury caused by pieces of broken
glass.  
LAMP HANDLING PRECAUTIONS
Lamp Replacement Counter
✔Note:
Do not reset the Lamp replacement counter without
implementation of lamp replacement.  Be sure to reset the Lamp
replacement counter only after replacing the lamp.
Select [Yes],
then another  
confirmation box
will appear.
Select [Yes] again 
to reset the lamp counter.
Maintenance & Cleaning
To reset the lamp counter, 
move the pointer to Reset and
then press the SELECT 
button.
“Lamp replacement counter
Reset?” dialog box will be
displayed.   
						

							54
Troubleshooting
Before calling your dealer or service center for assistance, check the items below once again.
–Make sure you have properly connected the projector to peripheral equipment as described on page15-17. 
–Make sure all equipment is connected to AC outlet and the power is turned on.
–When you operate the projector with a computer and it does not project an image, restart the computer.  
Appendix
Problem:–Solutions
No power–Plug the power cord of the projector into the AC outlet.
–See if the POWER indicator lights red.
–Wait 90-120 seconds after the projector is turned off when turning 
the projector back on.  The projector can be turned on after the 
POWER indicator turns red.  (See on page 19.)
–Check the WARNING indicator.  If the WARNING indicator lights red,
the projector cannot be turned on.  (See on page 49.)
–Check the projection lamp.  (See page 52.)
–Unlock Key lock for the projector Key lock function.  (See page 46.)
Image is out of focus.–Adjust focus of the projector.  (See page 22.)
–Provide proper distance between the projector and the projection 
screen.  (See page 13.)
–Check the projection lens to see if it needs cleaning.  (See page 51.)
–Moving the projector from a cool to a warm place may result in 
moisture condensation on the projection lens.  In such cases, leave 
the projector off and wait until condensation evaporates.
No image–Check the connection between your computer or video equipment 
and the projector.  (See page 15–17)
–See if the input signal is correctly output from your computer.  Some
laptop computers may need to change the setting for monitor output
when connecting to a projector.  See your computer’s instruction 
manual for the setting. 
–It takes about 30 seconds to display an image after turning on the 
projector.See if the selected system is corresponding with your 
computer or video equipment.  (See page 26 and 36)
–Select correct input source once again through menu operation.
(See page 25 ,34 and 35)
–Make sure the temperature is not out of the specified Operating 
Temperature (41 ˚F ~ 95 ˚F (5 ˚C ~ 35 ˚C)) .
Image is Left/Right reversed.–Check the Ceiling / Rear function.  (See page 44.)
Image is Top/Bottom reversed.–Check the Ceiling function.  (See page 44.)
No sound–  Check audio cable connection from audio input source.
–  Adjust the audio source.
–  Press the Volume+ button.  (See page 23.)
–  Press the Mute button.   (See page 23.)  
						

							55
This symbol on the nameplate means the product 
is Listed by Underwriters Laboratories Inc.  It is 
designed and manufactured to meet rigid U.L. 
safety standards against risk of fire, casualty and 
electrical hazards.
Appendix
The CE Mark is a Directive 
conformity mark of the European 
Community (EC).
Some displays are not seen–Check the Display function.  (See page 41.)
during  the operation.
PIN code dialog box appears at start-up.–PIN code lock is being set.  Input a PIN code (1234 or 
numbers you have set).  (See page 18, 46, 47.)
Computer 2 cannot be selected.–Select Computer 2 at the Terminal function.  (See page 44.) 
The Terminal function cannot be selected.–The Terminal function cannot be selected after Computer 2 is 
selected.  Select other input source such as Computer 1 or 
Video with the INPUT  button on the top control, the 
COMPUTER button or the VIDEO button on the remote 
control so that the Terminal function can be selected.   
The Remote Control does not work.–Check the batteries.
–Make sure no obstruction is between the projector and 
remote control.
–Make sure you are not too far from the projector when using 
the remote control.  Maximum operating range is 16.4’ (5m).
–Make sure the code of the remote control is conformed to 
the projector. (See page 45.)
–Unlock Key lock for the remote control in the Key lock 
function.  (See page 46.)
Cooling fans are still running after –This is normal condition.  Fans are running about 1
the AC plug is disconnected.minute even after disconnecting the AC plug.  
WARNING :
High voltages are used to operate this projector.  Do not attempt to open the cabinet.
If problems still persist after following all operating instructions,
contact the dealer where you purchased the
projector or the service center.Give the model number and explain about the problem.  We will advise you
how to obtain service.
Appendix 
						

							56
Appendix
Menu Tree
Mode 1Mode 2SVGA 1- - - -
Auto PC Adj.Fine sync.Total dotsHorizontalVertical
Display area - HDisplay area - VReset
Dynamic
RealBlackboard(Green)Image 1Image 2Image 3
Image AdjustContrastBrightnessColor temp.
Red
Gamma
Store
Quit
NormalTrueWideFull screenDigital zoom +
0 - 31
0 - 630 - 63
Computer Input
PC Adjust
Mode 1Mode 2Mode 3Mode 4Mode 5
Image Select
High
0 - 63
0 - 15
Image 1Image 2Image 3Image 4
Screen
Quit
Yes / No
✽Systems displayed in the System Menu vary
depending on an input signal.
ResetYes / No
Sharpness0 - 15
Computer Input / Video Input
Image 4
Sound
VolumeMute
QuitOn / OffSound0 - 63
Input
Computer 2
VideoAuto
Go to System(3)
Go to System(3)
Computer 1
Video 
Go to System(3)
✽N/A - - -not applicable
RGB( Analog )
Component
Go to System(1)
Go to System(2)
N/A
S-Video
RGB( Scart )  
Standard
Mode 1Mode 2Mode 3Mode 4Mode 5Quit
H-sync freq.
V-sync freq.QuitClampCurrent mode
Digital zoom –
GreenBlue0 - 630 - 63
Quit
Quit
Store
Mode free
System (1)
Quit
MidLow
XLow
Quit
Adj. 
						

							57
Appendix
AutoPALSECAMNTSCNTSC 4.43PAL-MPAL-N
Video Input
Auto1080i1035i720p575p480p575i480i
Dynamic
CinemaBlackboard(Green)Image 1Image 2Image 3
Quit
NormalWide
0 - 630 - 63
Off
Setting
Image Select
System (2)
System (3)
Image AdjustContrastBrightnessColorTint
RedGreenBlueSharpness
ResetStore
Gamma
Progressive
0 - 630 - 630 - 630 - 15 0 - 15
Image 1
Screen
Yes / No
Quit
Color temp.
Image 4
LanguageSettingEnglishGermanFrenchItalianSpanishPortugueseDutchSwedish
ChineseKoreanJapanese
On / OffOn / Countdown off / Off 
Logo select
On / OffOn / Off
Off
On / OffNormal / Auto / Eco
Code 1 / Code 2
KeystoneBlue backDisplay
Logo
CeilingRear
Power management
On startLamp control
Remote control
Quit
Russian
ReadyShut down
Hour(s)Lamp counter
Security
PIN code lock
Quit
Timer(1-30 Min)Quit
Factory default
L1 / L2Fan
Quit
Standard
Finnish
HungarianRomanian
Polish
OffNoise reduction
Yes / No
Appendix
Store / Reset
L1L2
HighMidLow
XLow
0 - 630 - 63
Image 2Image 3Image 4
L2L1
Quit
Off
UserCapture
Yes / No
OffOn
PIN code change
Logo PIN code lockLogo PIN code entry
Quit
OffProjector
Remote control
Quit
Key lock
Default
OffOn
PIN code change
PIN code lock entry
Quit
Adj.
Computer 2 /Monitor outTerminal
ResetQuit
Film 
						

							58
Appendix
Check the indicators for projector condition.  
• • • green.• • • red• • • off
• • • blinks green.
✽When the life of the projection lamp draws to an end, the LAMP REPLACE indicator lights yellow.
When this indicator lights yellow, replace the projection lamp with a new one promptly.  Reset the lamp
replacement counter after replacement of the lamp.  See page 52 and 53.
The projector is off.  (The AC power cord is unplugged.)
The projector is preparing for stand-by or the projection lamp is
being cooled down.  The projector cannot be turned on until cooling
is completed. 
The temperature inside the projector is abnormally high.  The
projector cannot be turned on.  When  the projector is cooled down
enough and the temperature returns to normal, the POWER
indicator emits a red light and the projector can be turned on.  (The
WARNING indicator keeps blinking.)  Check and clean the air filters.
Projector Condition
The projector is ready to be turned on with the POWER ON-OFF
button.
POWERred/green
Indicators
LAMP
REPLACE
yellow
WARNING red
The projector detects an abnormal condition and cannot be turned
on.  Unplug the AC power cord and plug it again to turn on the
projector.  If the projector is turned off again, disconnect the AC
power cord and contact the dealer or the service center for service
and checkup.  Do not leave the projector on.  It may cause an
electric shock or a fire hazard.
✽
✽
✽
✽
✽
The projector is operating normally. 
The projector is in the Power management mode. 
✽
✽
The projector has been cooled down enough and the temperature
returns to normal.  When turning on the projector, the WARNING
indicator stops blinking.  Check and clean the air filters.
Indicators and Projector Condition
• • • blinks red. 
						

							59
Appendix
Compatible Computer Specifications
LC-SB22 (SVGA) can basically accept the signal from all computers with the V, H-Frequency mentioned
below and less than 100 MHz of Dot Clock.
Appendix
ON-SCREEN
DISPLAYRESOLUTIONH-Freq.
(kHz)V-Freq.
(Hz)
VGA 1640 x 48031.4759.88
VGA 2720 x 40031.4770.09
VGA 3640 x 40031.4770.09
VGA 4640 x 48037.8674.38
VGA 5640 x 48037.8672.81
VGA 6640 x 48037.5075.00
MAC LC13640 x 48034.9766.60
MAC 13640 x 48035.0066.67
MAC 16832 x 62449.7274.55
MAC 191024 x 76860.2475.08
SXGA 11152 x 86464.2070.40
SVGA 1800 x 60035.15656.25
SVGA 2800 x 60037.8860.32
SVGA 3800 x 60046.87575.00
SVGA 4800 x 60053.67485.06
SVGA 5800 x 60048.0872.19
SVGA 6800 x 60037.9061.03
SVGA 7800 x 60034.5055.38
SVGA 8800 x 60038.0060.51
SVGA 9800 x 60038.6060.31
SVGA 11800 x 60038.0060.51
ON-SCREEN
DISPLAYRESOLUTIONH-Freq.
(kHz)V-Freq.
(Hz)
XGA 101024 x 768
XGA 111024 x 768
XGA 121024 x 768
XGA 131024 x 768
62.0477.07
XGA 141024 x 768
61.0075.70
XGA 151024 x 768
35.52286.96
(Interlace)
46.9058.20
XGA 81024 x 768
47.0058.30
XGA 91024 x 768
58.0372.00
SXGA 41280 x 1024
63.4879.35
36.0087.17
(Interlace)
63.3459.98
SXGA 51280 x 1024
SXGA 61280 x 1024
SXGA 71280 x 1024
63.7460.01
71.6967.19
SXGA 101280 x 960
81.1376.107
60.0060.00
XGA 11024 x 768
XGA 41024 x 768
48.3660.00
XGA 61024 x 768
XGA 71024 x 768
56.47670.07
48.5060.02
44.0054.58
SXGA 81280 x 1024
SXGA 91280 x 1024
63.9860.02
79.97675.025
XGA 51024 x 76860.3174.92
VGA 7640 x 48043.26985.00
575i––––––––15.62550.00
(Interlace)480i––––––––15.73460.00
(Interlace)
SXGA 121152 x 90071.4075.60
SXGA 111152 x 90061.2065.20
SVGA 10800 x 60032.7051.09
SXGA 131280 x 102450.0086.00
(Interlace)
SXGA 21280 x 102462.5058.60
SXGA 31280 x 102463.9060.00
XGA 21024 x 76868.67784.997
XGA 31024 x 76860.02375.03
SXGA 181280 x 102446.4386.70
(Interlace)
SXGA 191280 x 102463.7960.18
SXGA 141280 x 1024
SXGA 151280 x 1024
SXGA 161280 x 1024
SXGA 171152 x 900
50.0094.00
(Interlace)
63.3760.01
76.9772.00
61.8566.00
MAC1280 x 96075.0075.08
MAC1280 x 1024
480p––––––––
575p––––––––
80.0075.08
31.4759.88
1080i––––––––
31.2550.00
33.7560.00
(Interlace)
720p––––––––
1035i––––––––
45.0060.00
33.7560.00
(Interlace)
1080i––––––––28.12550.00
(Interlace)
SXGA 211400 x 105063.97960.190
MAC211152 x 87068.6875.06
UXGA 41600 x 120093.7575.00
WXGA 21360 x 768
WXGA 31376 x 768
WXGA 41360 x 768
UXGA 11600 x 1200
47.7060.00
UXGA 21600 x 1200
48.3660.00
UXGA 31600 x 1200
56.1672.00
75.0060.00
81.2565.00
WXGA 11366 x 768
87.570.00
48.3660.00
SXGA 221400 x 105065.34660.116
SXGA 231400 x 105065.12159.902
SXGA 201280 x 102491.14685.024
✳
✳
✳
✳
✳
✳
✳
✳
✳
✳
With selecting these modes, PC adjustment can be limited.✳
✳
✳
✳
✳
✳
✳
✳
✳
✳
✳
✳
✳
✳
✳
✳ 
						

							60
Appendix
Technical Specifications
Mechanical Information
Projector Type Multi-media Projector
Dimensions (W x H x D) 9.66 x 2.3 x 6.82 (294.5mm x 69.5mm x 208mm) (Not including adjustable feet)
Net Weight 5.5 lbs (2.5kgs)
Feet Adjustment 0˚ to 10.0˚
Panel Resolution
LCD Panel System 0.6 TFT Active Matrix type, 3 panels 
Panel Resolution 800 x 600 dots
Number of Pixels 1,440,000 (800 x 600 x 3 panels)
Signal Compatibility
Color SystemPAL, SECAM, NTSC, NTSC4.43, PAL-M, PAL-N
High Definition TV Signal 480i, 480p, 575i, 575p, 720p, 1035i, and 1080i
Scanning Frequency H-sync. 15 ~ 100 KHz, V-sync. 50 ~ 100 Hz
Optical Information
Projection Image Size (Diagonal) Adjustable from 40 to 300
Projection Lens F 1.65 ~ 1.81 lens with f 22.5 mm ~ 27 mm with manual zoom and focus
Throw Distance 4.6’ - 43.3’ (1.4m - 13.2m)
Projection Lamp 200W 
Interface
Video Input Jack RCA Type x 1 
S-Video Input Jack Mini DIN 4 pin x 1
Audio Input Jacks RCA Type x 2
Computer Input 1 / Component Input Terminal Analog RGB (Mini D-sub 15 pin) Terminal X 1
Computer Input 2 / Monitor Output Terminal
Analog RGB (Mini D-sub 15 pin) Terminal X 1  (In / Out switchable)
Computer/ Component Audio Input JackMini Jack (stereo) x 1
Service Port Connector Mini DIN 8 pin x 1
USB Connector USB Series B receptacle x 1
Audio Output Jack Mini Jack (stereo) x 1  (Variable)
Audio
Internal Audio Amp 1.0W RMS
Built-in Speaker 1 speaker, ø1.1 (28mm) 
Power
Voltage and Power Consumption AC 100 ~ 120 V (3.2A  Max. Ampere), 50 / 60 Hz  (The U.S.A and Canada)
AC 200 ~ 240 V (1.6A  Max. Ampere), 50 / 60 Hz  (Continental Europe and The U.K.)
Operating Environment
Operating Temperature 41 ˚F ~ 95 ˚F (5 ˚C ~ 35 ˚C)
Storage Temperature 14 ˚F ~ 140 ˚F (-10˚C ~ 60 ˚C)
Remote Control
Battery AA or LR6 1.5V ALKALINE TYPE x 2
Operating Range 16.4’ (5m) / ±30˚
Dimensions 1.9”(W) x 0.87”(H) x 5.7”(D) (49mm x 22mm x 145.3mm)
Net Weight 3.53 oz (100 g) (including batteries)