Eiki Projector Lc Hdt10 User Manual
Here you can view all the pages of manual Eiki Projector Lc Hdt10 User Manual. The Eiki manuals for Projector are available online for free. You can easily download all the documents as PDF.
Page 41
41 APPENDIX Check number of lamp to be replaced on Lamp Status Display. Remove two screws on Lamp Cover and press button to open Lamp Cover. (See right figure.) 1 3 Loosen two screws and pull out Lamp Assembly to be replaced by grasping handle.4 Turn off a projector and disconnect AC Power Cord. Allow a projector to cool down for at least 45 minutes.2 Replace Lamp Assembly with a new one and tighten two screws. Make sure Lamp is set properly 6 Follow these steps to replace lamp assembly. Replace Lamp...
Page 42
42 APPENDIX This projector uses a high-pressure lamp which must be handled carefully and properly. Improper handling may result in accidents, injury, or create a fire hazard. Lamp lifetime may differ from lamp to lamp and according to the environment of use. There is no guarantee of the same lifetime for each lamp. Some lamps may fail or terminate their lifetime in a shorter period of time than other similar lamps. If the projector indicates that the lamp should be replaced, i.e., if the LAMP REPLACE...
Page 43
43 Check audio cable connection from audio input source. Adjust audio source. Press VOLUME (+) button. Press MUTE button. TROUBLESHOOTING Before calling your dealer or service center for assistance, check matters below once again. 1. Make sure you have connected a projector to your computer or video equipment as described in section CONNECTING PROJECTOR on pages 12 ~ 15. 2. Check cable connection. Verify that all computer, video and power cord are properly connected. 3. Verify that all power is...
Page 44
44 APPENDIX SERVICE WARNING: High voltages are used to operate this projector. Do not attempt to open cabinet. You can often correct operating problems yourself. If a projector fails to work properly, see TROUBLESHOOT- ING section on pages 43-44. To correct failure, try Solutions. This symbol on the nameplate means the product is Listed by Underwriters Laboratories Inc. It is designed and manufactured to meet rigid U.L. safety standards against risk of fire, casualty and electrical hazards. The CE Mark...
Page 45
45 APPENDIX INDICATORS AND PROJECTOR CONDITION Check the Indicators for projector condition. • • • on : red• • • dim• • • off• • • flashing : red ✽When the life of the projection lamp draws to an end, the LAMP REPLACE indicator lights yellow. When this indicator lights yellow, replace the projection lamp with a new one promptly. Reset the Lamp Replace Counter after replacement of the lamp. The projector is OFF. (The MAIN switch OFF position or the AC Power Cord is unplugged.) The projector is...
Page 46
46 APPENDIX SDI 1SYSTEM Input 2 Y, Pb/Cb, Pr/Cr SYSTEM 3) 1) Input 1 RGB Input 2)System System SVGA 3 Custom SVGA 1 SVGA 2 Auto PC Adj. Fine sync Total dots Horizontal Vertical Current mode Clamp Display area Display area H Display area V Store Quit 0 - 31 Display adjust 720 x 400 800 x 600 1024 x 768 1152 x 864 1280 x 720 1280 x 1024 Quit 1600 x 1200 Yes/No 1) 1080i/50 1035i Auto 1080i/60 575p 480p 720p 575i Mode 1 ~ Mode 20 640 x 480 Reset SYSTEM2) Input 3RGB (Analog) RGB (Scart) SYSTEM1) RGB (PC...
Page 47
47 APPENDIX Lamp 2 Sound Mute Quit Volume Built-in SP.On/Off On/Off 0 - 63 LanguageSettingEnglish German French Italian Spanish Portuguese Dutch Swedish Chinese Korean Japanese On/Off On/Off On/Off On/Off Off/Ready/Shut down On/Off 4 Lamp/2 Lamp Lamp 1 Menu position Ceiling Power management On start Lamp mode Remote control code Lamp counter reset Code 1 Code 3 Code 4 Code 5 Code 6 Code 7 Code 8 Quit Quit Russian Logo Control panel Key lock Remote control Off Yes/NoFactory default Blue backOn/Off...
Page 48
48 APPENDIX Owner’s Manual AC Power Cord Wireless/Wired Remote Control Transmitter and Batteries Remote Control Cable DVI-VGA Cable and DVI Cable MAC/VGA Adapter 6 Types Light-Block Sheet (For option lens) 2 Types Lens Attachment (For option lens) Protective Dust Cover TECHNICAL SPECIFICATIONS 1.65 TFT Active Matrix type, 3 panels Multi-media Projector 83.9 lbs (38 kg) 22.9 x 10 x 30.9 (581 mm x 252 mm x 783 mm) 1920 x 1080 dots 6,220,800 (1920 x 1080 x 3 panels) PAL, SECAM, NTSC, NTSC4.43, PAL-M and...
Page 49
49 APPENDIX CONFIGURATIONS OF TERMINALS DVI-I TERMINAL (DIGITAL/ANALOG) This terminal accepts only Digital (TMDS) or Analog (RGB) output signal. Connect display output terminal of computer to this terminal with DVI cable (supplied). 1917 21018 31119 41220 51321 61422 71523 81624 C1 C2 C3 C5C4 T.M.D.S. Data2– No Connect T.M.D.S. Data2+ No Connect T.M.D.S. Data2 Shield DDC Clock DDC Data Analog Vert. sync 1 5 2 4 3 6 7 8 Pin Configuration T.M.D.S. Data1– No Connect T.M.D.S. Data1+ No Connect T.M.D.S....
Page 50
50 APPENDIX COMPATIBLE COMPUTER SPECIFICATIONS Basically this projector can accept a signal from all computers with V, H-Frequency mentioned below and less than 230 MHz of Dot Clock. –––––––– (Interlace) 1024 x 768 (Interlace) ON-SCREEN DISPLAYRESOLUTIONH-Freq. (kHz)V-Freq. (Hz) VGA 1640 x 48031.4759.88 VGA 2720 x 40031.4770.09 VGA 3640 x 40031.4770.09 VGA 4640 x 48037.8674.38 VGA 5640 x 48037.8672.81 VGA 6640 x 48037.5075.00 MAC LC13640 x 48034.9766.60 MAC 13640 x 48035.0066.67 MAC 16832 x...