Eiki Projector Lc Hdt10 User Manual

11
CONNECTING PROJECTOR
TERMINALS OF PROJECTOR
This projector applies various input/output terminals and 4 terminal slots for expansion to tune to diversity of signals from
computers and video equipment. 4-built-in Terminal Slots enable you to arrange desired combinations of input sources just
by changing Terminal Boards.  For Terminal Boards, contact sales dealer where you purchased a projector.
Pull out terminal by holding handle.
Remove 2 Screws on terminal.1
2
REPLACEMENT OF TERMINAL
Tighten screws...

12
CONNECTING PROJECTOR
INPUT 1 INPUT 2 INPUT 3
DVIAUDIOCONTROL PORT CONTROL PORT
AUDIO
R/Pr G/Y B/Pb H/HV V
(MONO)
(MONO)
RL
RL
(MONO)
AUDIO OUTRL
R/C JACKUSB
SERIAL PORT IN
SERIAL PORT OUT
RESET
INPUT 4
SDI IN1 SDI IN2SDI OUT
Connect audio output
from computer or video
equipment to these jacks.
(Refer to P14, 15.)
CONTROL PORT CONNECTORS
AUDIO INPUT JACKS
5 BNC INPUT JACKS
Connect component video output (Cr, Y,
Cb or Pr, Y, Pb) from video equipment to
R/Pr, G/Y and B/Pb jacks or connect
computer output...

13
CONNECTING PROJECTOR
Connect an external audio
amplifier to these jacks.  
(Refer to P14, 15.)
AUDIO OUTPUT JACKS
This projector uses a micro processor to control unit.
Occasionally, micro processor may malfunction and
need to be reset.  This can be done by pressing
RESET button with a pen, which will shut down and
restart unit. Do not use RESET function excessively.
RESET BUTTON
When using Wired / Wireless Remote
Control Unit as Wired Remote
Control, Connect Wired Remote
Control Unit to this jack...

INPUT 1 INPUT 2 INPUT 3
DVIAUDIOCONTROL PORT CONTROL PORT
AUDIO
R/Pr G/Y B/Pb H/HV V
(MONO)
(MONO)
RL
RL
(MONO)
AUDIO OUTRL
R/C JACKUSB
SERIAL PORT IN
SERIAL PORT OUT
RESET
INPUT 4
SDI IN1SDI IN2SDI OUT
14
CONNECTING PROJECTOR
CONNECTING TO COMPUTER
IBM-compatible computers or Macintosh computers (VGA / SVGA / XGA / SXGA/UXGA)
DVI-VGA Cable 
Monitor Output 
Desktop type
Laptop type
Audio Cable
(stereo) ✽
Audio Output
Audio Input AUDIO OUT
MAC/VGA
Adapter
Set slide switches
following chart
below.
Cables...

15
CONNECTING PROJECTOR
CONNECTING TO VIDEO EQUIPMENT
INPUT 1 INPUT 2 INPUT 3
CONTROL PORT CONTROL PORT
AUDIO
R/Pr G/Y B/Pb H/HV V
(MONO)
RL
(MONO)
AUDIO OUTRL
R/C JACKUSB
SERIAL PORT IN
SERIAL PORT OUT
RESET
INPUT 4
SDI IN1SDI IN2SDI OUT
DVIAUDIO
(MONO)
RL
Video Source (example)
Audio AmplifierAudio Speaker (stereo)
Audio Cable 
(Stereo) ✽
Audio Input
Cables used for connection
• Video Cable (BNC)✽
• Audio Cable (RCA x 2) ✽
• Scart Cable ✽
• DVI-VGA Adapter ✽
(✽= Cables are not supplied with this...

16
IMAGE button
Selects image levels.
(P32)
BEFORE OPERATION
MENU
AUTO PC ADJUST
IMAGE SELECTVOLUME
ZOOM FOCUS
LENS SHIFTON-OFFINPUT 1/2
INPUT 3/4
SIDE CONTROLS AND INDICATORS
Adjust zoom. (P23)
INPUT 3/4 button
POWER ON–OFF buttonFOCUS buttonsVOLUME buttons
Select input source either
INPUT 3 or INPUT 4.  (P25)
Adjust focus. (P23)Adjust volume. (P24)
Selects an item or adjusts
value in the On-Screen Menu.
(P20)
Executes the item selected.
(P20)
Turns the projector on or
off. (P22)
ZOOM buttons
Select...

17
BEFORE OPERATION
READYLAMP
LAMP
REPLACEWARNING
TEMP.
READY indicatorLAMP indicatorLAMP REPLACE indicator
This indicator lights green
when a projector is ready to
be turned on. And it flashes
green in Power Management
mode or internal projector
temperature is to high.
(P37, 39)This indicator is dim when a
projector is turned on.  And
bright when a projector is in
stand-by mode.
INDICATORS
WARNING TEMP. indicator
This indicator flashes red
when internal projector
temperature is too high.
(P39)
WARNING...

18
BEFORE OPERATION
OPERATION OF REMOTE CONTROL
RESET



FOCUSZOOM
ON-OFF
SELECT
q
w
y
u
!0
e
r
t
o
i
!2
!3
!4
!6
!7
!8
!5
!9
!1
!9RESET switchSlide this switch to the RESET to initialize the remote control code.
(P19, 37)
wSIGNAL EMISSION indicatorThis indicator lights red while a signal is being sent from the remote control
to the projector.
eSCREEN buttonSelect image screen. (P28)
rZOOM buttonAdjust zoom. (P23)
!7INPUT 1-4 buttonsSelect input source (INPUT 1-INPUT 4). (P25)
iPOINT (UP/DOWN/LEFT/RIGHT)...

Remote Control CodeNumber of Times of
Pressing IMAGE
Button
19
BEFORE OPERATION
To insure safe operation, please observe following precautions :
Use (2) AA, UM3 or R06 type alkaline batteries.
Replace two batteries at same time.
Do not use a new battery with an used battery.
Avoid contact with water or liquid.
Do not expose Remote Control Unit to moisture, or heat.
Do not drop Remote Control Unit.
If a battery has leaked on Remote Control Unit, carefully wipe case clean and install new batteries....

20
BEFORE OPERATION
HOW TO OPERATE ON-SCREEN MENU
FLOW OF ON-SCREEN MENU OPERATION
Display ON-SCREEN MENU
Press MENU button to display ON-SCREEN MENU (MENU
BAR).  A red frame is POINTER.
Move POINTER (red frame) to MENU ICON that you want to
select by pressing POINT RIGHT / LEFT buttons.
Adjust ITEM DATA by pressing POINT RIGHT / LEFT
buttons.
Refer to following pages for details of respective
adjustments.
Press POINT UP/DOWN button and move POINTER (red
frame or red arrow) to ITEM that you want to...