Eiki Projector EK-611W User Manual

							— 56 — 
DLP Projector — Owner’s Manual
Cleaning the Projector
Cleaning the projector to remove dust and grime will help ensure trouble\
-free operation.
Warning: 
•	Be sure to turn off and unplug the projector at least 30 minutes before \
cleaning. Failure to do so 
could result in a severe burn.
•	Use only a dampened cloth when cleaning. Do not allow water to enter the\
 ventilation openings on 
the projector.
•	If a little water gets into the projector interior while cleaning, leave\
 unplugged in a well-ventilated 
room for several hours before using.
•	If a lot of water gets into the projector interior when cleaning, have t\
he projector serviced.
Cleaning the Lens
You can purchase Optical lens cleaner from most camera stores. Refer to t\
he following to clean the 
projector lens.
1. Apply a little Optical lens cleaner to a clean soft cloth. (Do not appl\
y the cleaner directly to the lens.)
2. Lightly wipe the lens in a circular motion.
Caution: 
•	Do not use abrasive cleaners or solvents.
•	To prevent discoloration or fading, avoid getting cleaner on the projecto\
r case.
Cleaning the Case
Refer to the following to clean the projector case.
1. Wipe off dust with a clean dampened cloth.
2. Moisten the cloth with warm water and mild detergent (such as used to w\
ash dishes), and then wipe the 
case.
3. Rinse all detergent from the cloth and wipe the projector again.
Caution: 
To prevent discoloration or fading of the case, do not use abrasive alcoh\
ol-based cleaners.  
						

							— 57 — 
DLP Projector — Owner’s Manual
Using the Kensington® Lock
If you are concerned about security, attach the projector to a permanent object with the Kensington slot 
and a security cable.
Note: 
Contact your vendor for details on purchasing a suitable Kensington secu\
rity cable.
The security lock corresponds to Kensington’s MicroSaver Security System. If you have any comment, 
contact: Kensington, 2853 Campus Drive, San Mateo, CA 94403, U.S.A. Tel: 800-535-4242,  
http://www.Kensington.com.  
						

							— 58 — 
DLP Projector — Owner’s Manual
trOubleShOOtinG 
Common Problems and Solutions
These guidelines provide tips to deal with problems you may encounter wh\
ile using the projector. If
the problem remains unsolved, contact your dealer for assistance.
Often after time spent troubleshooting, the problem is traced to somethi\
ng as simple as a loose
connection. Check the following before proceeding to the problem-specific solutions.
 ¾Use some other electrical device to confirm that the electrical outlet is working.
 ¾Ensure the projector is turned on.
 ¾Ensure all connections are securely attached.
 ¾Ensure the attached device is turned on.
 ¾Ensure a connected PC is not in suspending mode.
 ¾Ensure a connected notebook computer is configured for an external display.  
(This is usually done by pressing an Fn-key combination on the notebook\
.)
Tips for Troubleshooting
• In each problem-specific section, try the steps in the order suggested. This may help you to solve the 
problem more quickly.
• Try to pin point the problem and thus avoid replacing non-defective parts\
. For example, if you replace 
batteries and the problem remains, put the original batteries back and g\
o to the next step.
• Keep a record of the steps you take when troubleshooting: The information may be useful when calling 
for technical support or for passing on to service personnel.   
						

							— 59 — 
DLP Projector — Owner’s Manual
LED Error Messages
The LED status indicators are located on the rear of the projector. Each LED is defined below.
•	Power LED
LeD statUsprojector statereDpUrpLebLUe
Steady LightOffOffStandby state (LAN connection is inactive).
Flashing (0.5 
sec on/0.5 sec 
off)
OffOffStandby state (LAN connection is active).
OffOffSteady LightPower is on and lamp is lighting.
OffFlashing (0.5 
sec on/0.5 sec 
off)
OffCooling for an abnormal shutdown.
Note: 
During
•	Lamp LED
LeD statUsprojector statereD
Steady LightLamp has failed and is in error state.
Flashing (3 sec on/1 sec off)Lamp driver has failed and lamp is in error state.
Flashing (1 sec on/1 sec off)Color wheel has failed.
•	Temp LED/Filter LED
LeD statUsprojector statetemp (reD)fILter (reD)
Steady LightOffOver temperature. The projector will shut down. 
Flashing (0.5 
sec on/0.5 
sec
OffFan has failed and is in error state.
Flashing (3 
sec on/1 sec 
off)
Flashing (1 
sec on/1 sec 
off)
Filter has overheated and is in error state.
OffSteady LightFilter switch has failed and is in error state.
•	Shutter LED
LeD statUsprojector statereD
Flashing (3 sec on/1 sec off)Projector is in burn in mode, lamp is lighting.
Flashing (1 sec on/1 sec off)Projector is in burn in mode and cooling.
Flashing (1 sec on/3 sec off)Projector is in burn in mode and lamp is off.
Steady LightShutter is on.  
						

							— 60 — 
DLP Projector — Owner’s Manual
Image Problems
Problem: No image appears on the screen
1. Verify the settings on your notebook or desktop PC.
2. Turn off all equipment and power on again in the correct order.
Problem: The image is blurred
1. Press the Focus button to adjust the focus on the projector.
2. Press the Auto button to automatically optimize image.
3. Ensure the projector-to-screen distance is within the specified range.
4. Check that the projector lens is clean.
Problem: The image is wider at the top or bottom (trapezoid effect)
1. Position the projector so it is as perpendicular to the screen as possib\
le.
2. Press the Keystone H or Keystone V button on the remote control to correct the problem.
Problem: The image is reversed
Check the Rear Projection on the Setup menu of the OSD.
Problem: The image is streaked
1. Set the Phase and Frequency settings on the Picture menu of the OSD to the default settings.
2. Ensure the problem is not caused by a connected PC’s video card, connect to another computer.
Problem: The image is flat with no contrast
Adjust the Contrast setting on the Picture menu of the OSD.
Problem: The color of the projected image does not match the source imag\
e
Adjust the Color Temperature and Gamma settings on the Picture > Advanced menu of the OSD.
Lamp Problems
Problem: There is no light from the projector
1. Check that the power cable is securely connected.
2. Ensure the power source is good by testing with another electrical devic\
e.
3. Restart the projector in the correct order and check if the Lamp LED indicator is flashing.
4. If you have replaced the lamp recently, try resetting the lamp connections.  
						

							— 61 — 
DLP Projector — Owner’s Manual
5. Replace the lamp module.
6. Put the old lamp back in the projector and have the projector serviced.
Problem: The lamp goes off
1. Power surges can cause the lamp to turn off. Re-plug power cord. When the Lamp LED is red, 
press “” on the built-in keypad or press “” on the remote control to turn off the projector. 
2. Replace the lamp module.
3. Put the old lamp back in the projector and have the projector serviced.
Remote Control Problems
Problem: The projector does not respond to the remote control
1. Direct the remote control towards remote sensor on the projector.
2. Ensure the path between remote and sensor is not obstructed.
3. Turn off any fluorescent lights in the room.
4. Make sure that the batteries are installed with the correct polarity.
5. Replace the batteries.
6. Turn off other Infrared-enabled devices in the vicinity.
7. Have the remote control serviced.
Having the Projector Serviced
If you are unable to solve the problem, you should have the projector se\
rviced. Pack the projector in the 
original carton. Include a description of the problem and a checklist of the steps you took when trying to fix 
the problem. The information may be useful to service personnel. For servicing, retur\
n the projector to the 
place you purchased it.    
						

							— 62 — 
DLP Projector — Owner’s Manual
HDMI Q & A
Q. What is the difference between a “Standard” HDMI cable and a “High-Speed” H\
DMI 
cable?
Recently, HDMI Licensing, LLC announced that cables would be tested as Standard \
or High- Speed 
cables.
• Standard (or “category 1”) HDMI cables have been tested to perfo\
rm at speeds of 75Mhz or up to 
2.25Gbps, which is the equivalent of a 720p/1080i signal.
• High Speed (or “category 2”) HDMI cables have been tested to per\
form at speeds of 340Mhz or up to 
10.2Gbps, which is the highest bandwidth currently available over an HDM\
I cable and can successfully 
handle 1080p signals including those at increased color depths and/or in\
creased refresh rates from the 
Source. High-Speed cables are also able to accommodate higher resolution\
 displays, such as WQXGA 
cinema monitors (resolution of 2560 x 1600).
Q. How do I run HDMI cables longer than 10 meters?
There are many HDMI Adopters working on HDMI solutions that extend a cable’s effective distance from 
the typical 10 meter range to much longer lengths. These companies manufacture a variety of solutions 
that include active cables (active electronics built into cables that b\
oost and extend the cable’s signal), 
repeaters, amplifiers as well as CAT5/6 and fiber solutions.
Q. How can I tell if a cable is an HDMI certified cable?
All HDMI products are required to be certified by the manufacturer as part of the HDMI Compliance Test 
Specification. However, there may be instances where cables bearing the HDMI logo are available but 
have not been properly tested. HDMI Licensing, LLC actively investigates\
 these instances to ensure that 
the HDMI trademark is properly used in the market. We recommend that consumers buy their cables from 
a reputable source and a company that is trusted.
For more detail information check http://www.hdmi.org/learningcenter/faq.aspx#49.  
						

							— 63 — 
DLP Projector — Owner’s Manual
SpecificatiOnS 
Specifications
ItemDescrIptIon
Display typeDMD, 0.7” XGA, 0.65” WXGA, 0.67” WUXGA
ResolutionXGA (1024 x 768), WXGA (1280 x 800), WUXGA (1920 x 1200)
Zoom/focusPower Focus / Zoom
Zoom ratioDepend on Lens
Keystone correctionVertical: +/- 20 degrees, Horizontal: +/- 20 degrees
Projection methodsFront, Rear, Desktop/Ceiling (Rear, Front)
Data compatibilityVGA, SVGA, XGA, WXGA, HD720, SXGA, SXGA+, UXGA, HD1080, 
HDTV, WUXGA, SDTV, Mac
Video compatibility1080 i/p, 720p, 576 i/p, 480 i/p
H-Sync15.7KHz~91.1KHz
V-Sync24Hz~85Hz
Safety CertificationCB, CCC
Operation temperature5° ~ 40°C
Dimensions (W x H x D)452.8 x 389.9 x 205.5 mm (without lens and elevators)
AC Input100 VAC – 240 VAC, 50 – 60Hz
Power consumption450W (ECO brightness mode), 580W (Normal brightness mode)
Lamp1500 hrs typical @ 465W
2000 hrs typical @ 360W
Input TerminalsHDBaseT:
HDMI:
DVI-I:
Y/Pb/Pr, Y/Cb/Cr:
VGA:
Video:
RJ45 jack x 1
HDMI (version 1.3; locking screw) x 1
DVI (supports only digital signal) x 1
D-sub 15 pin x 1
Control TerminalsLAN Control: 
Remote Control IN: 
Serial port (RS232C): 
Wi-Fi: 
Service:
RJ45 jack x 1
Mini jack (3.5mm) x 1
D-Sub 9 pin (Cross) x 1
USB Type A x 1
Mini USB x 1
SecurityKensington lock
Security Bar
Note:
For	questions	regarding	product	specifications,	please	contact	your	local	distributor.   
						

							— 64 — 
DLP Projector — Owner’s Manual
Projection Distance vs. Projection Size
Projection Distance and Size Table
XGA:
DIagonaLscreen sIZeprojectIon Lens
HeIgHtWIDtHn/an/an/an/an/a
 (IncH) (m) (m)mIn 
(m)
maX 
(m)
mIn 
(m)
maX 
(m)
mIn 
(m)
maX 
(m)
mIn 
(m)
maX 
(m)
mIn 
(m)
maX 
(m)
500.761.021.011.281.281.611.613.053.055.790.791.01
600.911.221.211.541.541.931.933.663.666.950.951.21
701.071.421.411.791.792.252.254.274.278.111.111.41
801.221.631.612.052.052.572.574.884.889.271.271.61
901.371.831.812.302.302.892.895.495.4910.421.431.81
1001.522.032.012.562.563.213.216.106.1011.581.582.01
11 01.682.242.212.822.823.533.536.716.7112.741.742.21
1201.832.442.413.073.073.853.857.327.3213.901.902.41
1301.982.642.623.333.334.174.177.927.9215.062.062.62
1402.132.842.823.583.584.494.498.538.5316.222.222.82
1502.293.053.023.843.844.824.829.149.1417.372.383.02
1602.443.253.224.104.105.145.149.759.7518.532.543.22
1702.593.453.424.354.355.465.4610.3610.3619.692.693.42
1802.743.663.624.614.615.785.7810.9710.9720.852.853.62
1902.903.863.824.864.866.106.1011.5811.5822.013.013.82
2003.054.064.025.125.126.426.4212.1912.1923.163.174.02
2503.815.085.036.406.408.038.0315.2415.2428.963.965.03
3004.576.106.047.687.689.639.6318.2918.2934.754.756.03
Projection Distance
Image Height  
						

							— 65 — 
DLP Projector — Owner’s Manual
WXGA:
DIagonaLscreen sIZeprojectIon Lens
HeIgHtWIDtHn/an/an/an/an/a
 (IncH) (m) (m)mIn 
(m)
maX 
(m)
mIn 
(m)
maX 
(m)
mIn 
(m)
maX 
(m)
mIn 
(m)
maX 
(m)
mIn 
(m)
maX 
(m)
500.671.081.081.381.381.741.733.323.286.240.851.08
600.811.291.291.651.652.082.063.963.927.461.021.29
700.941.511.511.931.932.432.424.644.598.731.191.51
801.081.721.722.202.202.772.755.285.239.941.361.72
901.211.941.942.482.483.123.105.965.9011.211.531.94
1001.352.152.152.752.753.463.446.606.5412.431.702.15
11 01.482.372.373.033.033.823.797.287.2013.701.872.37
1201.622.582.583.303.304.154.137.927.8414.912.042.58
1301.752.83.023.583.584.514.488.608.5116.182.212.80
1401.883.023.023.873.874.864.839.279.1817.462.393.02
1502.023.233.234.134.135.205.179.929.8218.672.553.23
1602.153.453.454.424.425.555.5210.5910.4919.942.733.45
1702.293.663.664.684.685.895.8611.2411.1321.152.893.66
1802.423.883.884.974.976.256.2111.9111.8022.433.073.88
1902.564.094.095.245.246.586.5412.5612.4323.643.234.09
2002.694.314.315.525.526.946.9013.2313.1024.913.404.31
2503.375.385.386.896.898.668.6116.5216.3631.104.255.38
3004.046.466.468.278.2710.4010.3419.8319.6437.345.106.46