Eiki Projector EK-611W User Manual

							— 6 — 
DLP Projector — Owner’s Manual
Bottom View
241.2mm
105.8mm
216.2mm130.8mm
160mm9 5.4mm95mm
125.4mm
2
2
2
2
11
1
ItemLabeLDescrIptIonsee page
1Adjustable FeetRaise or lower the feet to level the projector.13
2Ceiling support 
holes
Contact your dealer for information on mounting the projector on 
a ceiling.
viii-ix
Note: 
•	When installing, ensure that you use only UL Listed ceiling mounts. 
•	For ceiling installations, use approved mounting hardware and M6 x 4 scr\
ews with a maximum 
screw depth of 10 mm (0.39 inch).
•	The construction of the ceiling mount must be of a suitable shape and st\
rength. The ceiling mount 
load capacity must exceed the weight of the installed equipment, and as \
an additional precaution 
be capable of withstanding three times the weight of the equipment (not\
 less than 71.4 kg) over a 
period of 60 seconds.  
						

							— 7 — 
DLP Projector — Owner’s Manual
Remote Control Parts 
ONOFF
213
546
879
GammaBrightCont.PIP
0InfoMode
AutoSource
MenuExit
Hot KeyShutter(AV Mute)Patter n
FocusLens H
Lens V
Keystone  H
Keystone  V
Zoom
Enter
1
3
4
7
14
15
10
11
12
13
8
9
6
5
2
16
17
18
19
24
22
23
20
21
Important:
1.	Avoid	using	the	projector	with	bright	fluorescent	lighting	turned	on.	Certain	high-frequency	
fluorescent	lights	can	disrupt	remote	control	operation.
2. Be sure nothing obstructs the path between the remote control and the\
 projector. If the path 
between the remote control and the projector is obstructed, you can boun\
ce the signal off certain 
reflective	surfaces	such	as	projector	screens.
3. The buttons and keys on the projector have the same functions as the \
corresponding buttons on the 
remote control. This owner’s manual describes the functions based on the remote control.
Note:
Complies with FDA performance standards for laser products except for deviations pursuant\
 to  
Laser Notice No. 50, dated June 24, 2007.  
						

							— 8 — 
DLP Projector — Owner’s Manual
ItemLabeLDescrIptIonsee page
1Power onTurn projector ON.12
2Number KeysEnter a number (such as PIN code) or source hotkey.
Source Hotkey Key:
1: VGA
2: HDMI
3: Component
4: HDBaseT
5: Video
6: DVI-D
-
3InfoDisplay source image information.-
4AutoAutomatically optimize image.-
5Enter• Select a highlighted menu item.
• Change or accept a value.
19
6Arrow Keys• Adjust a setting UP or DOWN.
• Navigate within a menu.
19
7MenuDisplay menus.19
8GammaAdjust mid-range levels.-
9BrightAdjust amount of light in the image.-
10Lens HAdjust the position of the image horizontally.-
11Lens VAdjust the position of the image vertically.-
12Keystone HAdjust the horizontal keystone.14
13Keystone VAdjust the vertical keystone.14
14Shutter  
(AV Mute)
Display or blank the video image.-
15Hot KeySelect your preset keys quickly.39
16OFFTurn projector OFF.12
17ModeSelect the preset display mode.-
18SourceSelect an input for the main or PIP/PBP image.33
19ExitReturn to previous level or exit menus if at top level.19
20PIPTurn PIP/PBP ON/OFF.33
21Cont.Adjust difference between dark and light.-
22FocusAdjust focus to improve image clarity as desired.14
23ZoomAdjust zoom to achieve a desired image size.14
24PatternDisplay a test pattern.-
 Caution:
Use	of	controls,	adjustments	or	performance	of	procedures	other	than	those	specified	herein	may	
result in hazardous laser light exposure.  
						

							— 9 — 
DLP Projector — Owner’s Manual
Remote Control Operating Range  
The remote control uses infrared transmission to control the projector. It is not necessary to point the 
remote directly at the projector. Provided you are not holding the remote perpendicular to the sides or \
the rear of the projector, the remote will function well within a radius of about 7 meters (23 f\
eet) and 15 
degrees above or below the projector level. If the projector does not re\
spond to the remote control, move 
a little closer.
Projector and Remote Control Buttons 
The projector can be operated using the remote control or the buttons on\
 the top of the projector. All 
operations can be carried out with the remote control; however, the buttons on the projector are limited in 
use. 
Inserting the Remote Control Batteries 
1. Remove the battery compartment cover as shown in the  
illustration.
2. Insert the batteries with correct polarity (+/-) as shown inside  
the battery compartment.
3. Replace the cover.
Caution: 
•	Only use AAA batteries (Alkaline batteries are recommended). 
•	Dispose of used batteries according to local ordinance regulations.
•	Remove the batteries when not using the projector for prolonged periods.\
  
						

							— 10 — 
DLP Projector — Owner’s Manual
Setup and OperatiOn 
Installing the Projection Lens
Before setting up the projector, install the projection lens on the projector.
Important: 
•	Before installation, check where the projector is used and prepare a sui\
table lens.
•	For details, contact the sales dealer where you purchased the projector.
1. Turn the projector off. Allow the projector to cool down into standby mode.
2. Rotate the lens ring counter-clockwise and then 
remove it from the projector. 
3. Rotate the lens cover counter-clockwise and then  
remove it from the projector.
4. With the label “TOP” on the lens assembly facing up, 
install the assembly into the lens mount.     
						

							— 11 — 
DLP Projector — Owner’s Manual
5. While pulling the rejection pin, rotate the lens clockwise 
to lock the lens in place. Then release the rejection pin.  
6. Replace the lens ring.    
						

							— 12 — 
DLP Projector — Owner’s Manual
Starting and Shutting down the Projector
Turn the Projector On
1. Connect the power cord to the projector. Then connect the other end to a wall outlet.  
The Power button on the built in keypad is illuminated.
Important: 
Make sure that the Power switch is in the ON position.
2. Turn on the connected devices.
3. Turn on the projector by pressing “” on the remote control  
or press “” on the built-in keypad. The Power LED is  
Blue with steady light. 
The projector splash screen displays and connected  
devices are detected.
4. If more than one input device is connected, press the Source key on the remote control to select an 
input source (VGA, HDMI, Component, HDBaseT, BNC, or DVI).
5. The projector detects the source you selected and displays the image.
Note:
The	first	time	the	projector	is	used,	the	preferred	language	may	be	selected	from	the	main	menu	after	
the startup screen is displayed.
Turn the Projector Off
1. Press “” on the built-in keypad or press “” on the remote control to turn off the projector. A warning 
message will appear on the displayed image.
2. Press “” on the built-in keypad or press “” on the remote control again to confirm your selection. If 
you do not press “” or “” again, the warning message will disappear after 3 seconds.
Caution: 
•	Do not unplug the power cord until all of fans are stop–indicating th\
e projector has cooled down.          
						

							— 13 — 
DLP Projector — Owner’s Manual
Adjusting the Projector Level
Take note of the following when setting up the projector:
• The projector table or stand should be level and sturdy.
• Position the projector so that it is perpendicular to the screen.
• Ensure the cables are in a safe location. You could trip over them.
B
A
1. To raise the level of the projector, lift the projector A.
2. Locate the adjustable foot you wish to modify on the underside of the pr\
ojector.
3. Rotate the adjustable foot clockwise to raise the projector or counter-c\
lockwise to lower it. Repeat with 
the remaining feet as necessary B.  
						

							— 14 — 
DLP Projector — Owner’s Manual
Adjusting the Zoom, Focus, and Keystone
1. Use the Zoom button to resize the projected  
image and screen size B.
2. Use the Focus button to sharpen the  
projected image A.
3. Use the Keystone H buttons (on the remote control) to adjust the keystone  
horizontally and make a squarer image. Use the Keystone V buttons (on the  
remote control) to adjust keystone vertically and make a squarer image.
A
B
Hot KeyShutter(AV Mute)Pattern
FocusLens H
Lens V
Keystone H Keystone V
Zoom
Hot KeyShutter(A V Mute)Pattern
FocusLens H
Lens V
Keystone H Keystone V
Zoom  
						

							— 15 — 
DLP Projector — Owner’s Manual
Adjusting the Projecting image’s Position
To determine where to position the projector, consider the size and shape of your screen, the location of 
your power outlets, and the distance between the projector and the rest \
of your equipment.
HH
H0
V
V
V0
project
Ion Lens:  n /a
p
LatformH V
0.7” XGA 15%50%
0.67” WUXGA 15%50%
projectIon Lens:  n /a
p
LatformH V
0.7” XGA 15%35%
0.67” WUXGA 15%50%