Eiki Projector EK-601W User Manual

							— 57 — 
DLP Projector — Owner’s Manual
4. Slightly move the dust filter cover to the left and to the right direction to release it from the latches on the case. And then remove.
5. Install the new filter by reversing the previous steps.
Note: 
Dust	filters	are	only	required/supplied	in	the	selected	regions	with	excessive	dust.
Cleaning the projector
Cleaning the projector to remove dust and grime will help ensure trouble\
-free operation.
Warning: 
•	 Be sure to turn off and unplug the projector at least 30 minutes before \
cleaning. Failure to do so 
could result in a severe burn.
•	 Use only a dampened cloth when cleaning. Do not allow water to enter the\
 ventilation openings on 
the projector.
•	 If a little water gets into the projector interior while cleaning, leave\
 unplugged in a well-ventilated 
room for several hours before using.
•	 If a lot of water gets into the projector interior when cleaning, have t\
he projector serviced.
Cleaning the Lens
You can purchase Optical lens cleaner from most camera stores. Refer to t\
he following to clean the 
projector lens.
1. Apply a little Optical lens cleaner to a clean soft cloth. (Do not appl\
y the cleaner directly to the lens.)
2. Lightly wipe the lens in a circular motion.
Caution: 
•	Do not use abrasive cleaners or solvents.
•	 To prevent discoloration or fading, avoid getting cleaner on the projecto\
r case.  
						

							— 58 — 
DLP Projector — Owner’s Manual
Cleaning the Case
Refer to the following to clean the projector case.
1. Wipe off dust with a clean dampened cloth.
2. Moisten the cloth with warm water and mild detergent (such as used to w\
ash dishes), and then wipe the case.
3. Rinse all detergent from the cloth and wipe the projector again.
Caution: 
To prevent discoloration or fading of the case, do not use abrasive alcoh\
ol-based cleaners.
Using the Kensington® lock
If you are concerned about security, attach the projector to a permanent object with the Kensington slot 
and a security cable.
Note: 
Contact your vendor for details on purchasing a suitable Kensington secu\
rity cable.
The security lock corresponds to Kensington’s MicroSaver Security System. If you have any comment, 
contact: Kensington, 2853 Campus Drive, San Mateo, CA 94403, U.S.A. Tel: 800-535-4242,   
http://www.Kensington.com .  
						

							— 59 — 
DLP Projector — Owner’s Manual
trOubleShOOtinG 
Common problems and Solutions
These guidelines provide tips to deal with problems you may encounter wh\
ile using the projector. If
the problem remains unsolved, contact your dealer for assistance.
Often after time spent troubleshooting, the problem is traced to somethi\
ng as simple as a loose
connection. Check the following before proceeding to the problem-specific solutions. 
¾ Use some other electrical device to confirm that the electrical outlet is working.
 
¾ Ensure the projector is turned on.
 
¾ Ensure all connections are securely attached.
 
¾ Ensure the attached device is turned on.
 
¾ Ensure a connected PC is not in suspending mode.
 
¾ Ensure a connected notebook computer is configured for an external display .  
(This is usually done by pressing an Fn-key combination on the notebook\
.)
Tips for Troubleshooting
•  In each problem-specific section, try the steps in the order suggested.  This may help you to solve the 
problem more quickly.
•  Try to pin point the problem and thus avoid replacing non-defective parts\
. For example, if you replace 
batteries and the problem remains, put the original batteries back and g\
o to the next step.
•  Keep a record of the steps you take when troubleshooting: The information may be useful when calling 
for technical support or for passing on to service personnel.   
						

							— 60 — 
DLP Projector — Owner’s Manual
lED Error Messages
The LED status indicators are located on the top of the projector. Each LED is defined below.
•	 power lED
LeD status
reDbLueprojector state
Steady Light OffStandby state (power cord connected).
Off Flashing 
(0.5 second 
interval)Power is on (warming) or power is off (cooling).
Note: 
If the projector is in cooling state and the power LED turns red then it\
 
indicates that the fan has turned off.
Off Flashing 
(Flashing 
(0.25 second 
interval)The projector is in Quick Resume mode and can be powered on again 
within a 100 seconds.
Off FlashingStandby state, burnin (warning), or (burnin (cooling).
•	 Temp lED
LeD statusprojector statetemp (reD) poWer (reD)
Flashing FlashingFan has failed and is in error state.
Steady Light FlashingOver temperature. The projector will shut down.
•	 lamp lED
LeD statusprojector stateLamp (reD) poWer (reD)
Steady Light FlashingLamp has failed and is in error state.  
						

							— 61 — 
DLP Projector — Owner’s Manual
Image problems
Problem: No image appears on the screen
1. Verify the settings on your notebook or desktop PC.
2. Turn off all equipment and power on again in the correct order.
Problem: The image is blurred
1. Use the Focus lever to adjust the focus on the projector.
2. Ensure the projector-to-screen distance is within the specified range.
3. Check that the projector lens is clean.
Problem: The image is wider at the top or bottom (trapezoid effect)
1. Position the projector so it is as perpendicular to the screen as possib\
le.
2. Press the Keystone V button on the remote control or built-in keypad or manually adjust hori\
zontal keystone to correct the problem.
Problem: The image is reversed
Check the Rear projection on the  Setup menu of the OSD.
Problem: The image is streaked
1. Set the phase and Frequency settings on the picture > Signal (VGA input)  menu of the OSD to the 
default settings.
2. Ensure the problem is not caused by a connected PC’s video card, connect to another computer.
Problem: The image is flat with no contrast
Adjust the Contrast setting on the picture menu of the OSD.
Problem: The color of the projected image does not match the source imag\
e
Adjust the Color Temperature  and Gamma settings on the picture > Advanced menu of the OSD.
lamp problems
Problem: There is no light from the projector
1. Check that the power cable is securely connected.
2. Ensure the power source is good by testing with another electrical devic\
e.
3. Restart the projector in the correct order and check that the Lamp LED h\
as not turned to red.
4. If you have replaced the lamp recently, try resetting the lamp connections.  
						

							— 62 — 
DLP Projector — Owner’s Manual
5. Replace the lamp module.
6. Put the old lamp back in the projector and have the projector serviced.
Problem: The lamp goes off
1. Power surges can cause the lamp to turn off. Re-plug power cord. Press “” on the built-in keypad or 
the remote control to turn off the projector. 
2. Replace the lamp module.
3. Put the old lamp back in the projector and have the projector serviced.
Remote Control problems
Problem: The projector does not respond to the remote control
1. Direct the remote control towards remote sensors on the projector.
2. Ensure the path between remote and sensor is not obstructed.
3. Turn off any fluorescent lights in the room.
4. Make sure that the batteries are installed with the correct polarity.
5. Replace the batteries.
6. Turn off other Infrared-enabled devices in the vicinity.
7. Have the remote control serviced.
having the projector Serviced
If you are unable to solve the problem, you should have the projector se\
rviced. Pack the projector in the 
original carton. Include a description of the problem and a checklist of the steps you took when trying to fix 
the problem. The information may be useful to service personnel. For servicing, retur\
n the projector to the 
place you purchased it.    
						

							— 63 — 
DLP Projector — Owner’s Manual
hDMI Q & A
Q. What is the difference between a “Standard” HDMI cable and a “High-Speed” H\
DMI 
cable?
Recently, HDMI Licensing, LLC announced that cables would be tested as Standard \
or High- Speed 
cables.
•  Standard (or “category 1”) HDMI cables have been tested to perfo\
rm at speeds of 75Mhz or up to 
2.25Gbps, which is the equivalent of a 720p/1080i signal.
•  High Speed (or “category 2”) HDMI cables have been tested to per\
form at speeds of 340Mhz or up to 
10.2Gbps, which is the highest bandwidth currently available over an HDM\
I cable and can successfully 
handle 1080p signals including those at increased color depths and/or in\
creased refresh rates from the 
Source. High-Speed cables are also able to accommodate higher resolution\
 displays, such as WQXGA 
cinema monitors (resolution of 2560 x 1600).
Q. How do I run HDMI cables longer than 10 meters?
There are many HDMI Adopters working on HDMI solutions that extend a cable’s effective distance from 
the typical 10 meter range to much longer lengths. These companies manufacture a variety of solutions 
that include active cables (active electronics built into cables that b\
oost and extend the cable’s signal), 
repeaters, amplifiers as well as CAT5/6 and fiber solutions.
Q. How can I tell if a cable is an HDMI certified cable?
All HDMI products are required to be certified by the manufacturer as part of the HDMI Compliance  Test 
Specification. However, there may be instances where cables bearing the HDMI logo are available but 
have not been properly tested. HDMI Licensing, LLC actively investigates\
 these instances to ensure that 
the HDMI trademark is properly used in the market. We recommend that consumers buy their cables from 
a reputable source and a company that is trusted.
For more detail information check  http://www.hdmi.org/learningcenter/faq.aspx#49 .  
						

							— 64 — 
DLP Projector — Owner’s Manual
SpecificatiOnS 
Specifications
ItemDescrIptIon
Display type0.67” DMD WUXGA/0.65” DMD WXGA
Resolution 1920X1200(WUXGA)/ 1280X800(WXGA)
Zoom/focus Manual focus, automatic zoom
Zoom ratio 1.8x
Keystone correction Vertical and Horizontal: +/- 30 degrees
Projection methods Front, Rear, Fron-Ceiling, Rear-Ceiling
Data compatibility VGA, SVGA, XGA, SXGA, Quad VGA, SXGA+, UXGA, WUXGA(RB), 
WSVGA, WXGA, WXGA+, WSXGA, WUXGA, PowerBook G4, i Mac 
DV(G3)
Video compatibility 480i/p, 576i/p, 720p, 1080i/p
H-Sync 15.375~91.146 kHz
V-Sync 24~85Hz, 120Hz for 3D mode
Safety Certification cTUVus, FCC, CB, CE, CCC, CECP, EAC, KC/KCC, ICES-003:2016 Issue 
6, Class B
Operation temperature 5° ~ 40°C
Dimensions (W x H x D) 422.7 x 158.6 x 355.8 mm (with feet)
AC Input 100 VAC – 240 VAC
Power consumption 410W (ECO), 510W (Max. Full Mode)
Lamp 3000 hours at typical full power mode (445W)
4000 hours at Eco mode (355W)
Input Terminals VGA-IN/YPbPr:
Audio-IN:
MIC-IN:
Video:
S-Video:
HDMI:
DisplayPort:D-sub 15-pin female connector for VGA input and 
component video input x 2
Phone jack for audio input (3.5mm) x 3, RCA 
audio jacks for audio input x 2
Phone jack for microphone input (3.5mm) x 1
RCA jack for composite video input x 1
Mini DIN 4-pin  for S-video input x 1
HDMI1.4b  input x 2
DisplayPort input x 1
Output Terminals VGA-OUT: 
Ethernet:
Audio-OUT:
3D Sync OUT:D-sub 15-pin female connector for VGA output x 1
RJ45 connector for network management
Phone jack for audio output (3.5mm) x 1
Mini din 3-pin VESA 3D sync output connector x 1
Control Terminals RS-232C
USB-B Mini
USB Power OUTD-SUB 9-pin connector for HDBaseT firmware 
update and projector control x 1
For firmware update x 1
Type-A USB for power 5V/1.5A output.
Security Kensington lock   
						

							— 65 — 
DLP Projector — Owner’s Manual
Note:
For	questions	regarding	product	specifications,	please	contact	your	local	distributor.
Compatible Resolution
ItemsmoDeresoLutIonfrequency
V: [hz]h: [Khz]
1) VGA Analog – PC Signal VGA
640x480 60
31.47
72 37.86
75 37.5
85 43.27
SVGA 800x60056
35.2
60 37.88
72 48.08
75 46.88
85 53.67
XGA 1024x768 60
48.36
70 56.48
75 60.02
85 68.67
SXGA 1152x864
70
63.8
75 67.5
85 77.1
1280x1024 60
63.98
72 77.9
75 79.98
85 91.15
Quad VGA 1280x96060
60
75 75
SXGA+ 1400x1050 60
65.32
UXGA 1600x1200 60
75
WUXGA(RB) 1920x120060
74.038
PowerBook G4 640x480
60
31.5
66.6(67) 35
800x600 60
37.88
1024x768 60
48.36
1152x870 75
68.68
1280x960 75
75.2
i Mac DV(G3) 1024x76875
60.3  
						

							— 66 — 
DLP Projector — Owner’s Manual
ItemsmoDeresoLutIonfrequency
V: [hz]h: [Khz]
(2) VGA Analog – Extended Wide timing WSVGA
1024x600 6037.3
WXGA 1280x768
60
47.78
75 60.29
85 68.63
1280x720 60
44.8
1280x800 60
49.6
1366x768 60
47.71
WXGA+ 1440x900 60
55.9
WSXGA 1680x1050 60
65.3
WUXGA 1920x1080-RB
60
66.6
1920x1080-EIA 60
67.5
(3) VGA Analog – Component signal 480i
720x48059.94(29.97)
27
480p 59.94
31.47
576i 720x57650(25)
27
576p 50
31.25
720p 1280x720 60
45
50 37.5
1080i 1920x1080 60(30)
33.75
50(25) 33.75
1080p 60
67.5
50 56.25
ItemsmoDeresoLutIonfrequency
V: [hz]h: [Khz]
(1) HDMI & Displayport – PC Signal VGA
640x480 60
31.47
72 37.86
75 37.5
85 43.27
SVGA 800x60056
35.2
60 37.88
72 48.08
75 46.88
85 53.67
XGA 1024x768 60
48.36
70 56.48
75 60.02
85 68.67
SXGA 1152x864 70
63.8
75 67.5
85 77.1