Eiki Projector EK-601W User Manual

							— 7 — 
DLP Projector — Owner’s Manual
Remote Control parts 
On
Test
Mode Pattern
Mous
e
Switch
Off
F1 F2
AV Mute
ENTER
Source VolumeV  Keystone
Info
.
VGA1
1
S-Video
2
HDMI1
3
HDMI2
FormatZoomRemote
IDAll
VGA2
4
Video
5
DVI
6
BNC
7
YPbPr
8
DisplayPort
9
3D
0
Re-Sync
Menu Pg
4
8
15
16
11
12
13
14
9
6
3
5
7
10
30
17
18
19
24
22
23
25
26
27
28
29
20
21
2
1
Important:
1.	Avoid	using	the	projector	with	bright	fluorescent	lighting	turned	on.	Certain	high-frequency	
fluorescent	lights	can	disrupt	remote	control	operation.
2. Be sure nothing obstructs the path between the remote control and the\
 projector. If the path  between the remote control and the projector is obstructed, you can boun\
ce the signal off certain 
reflective	surfaces	such	as	projector	screens.
3. The buttons and keys on the projector have the same functions as the \
corresponding buttons on the  remote control. This owner’s manual describes the functions based on the remote control.
Note:
Complies with FDA performance standards for laser products except for deviations pursuant\
 to   
Laser Notice No. 50, dated June 24, 2007.  
						

							— 8 — 
DLP Projector — Owner’s Manual
ItemLabeLDescrIptIonsee page
1Power on Turn projector ON. 11
2 Pattern Display a test pattern. -
3 Function button 
(F1) (Assignable) Programmable function button.
-
4 Mode/Mouse left 
click • 
Display mode menu on/off.
•  Use as mouse left click when mouse is switched on. -
5 Arrow Keys • Adjust a setting UP/DOWN or LEFT/RIGHT.
•  Navigate within a menu. 17
6 Info. Display source image information. -
7 Source Press “Source” to select an input signal. -
8 Menu Display menus. 17
9 Volume - / + Press to increase or decrease the volume. -
10 Zoom Adjust zoom to achieve a desired image size. 14
11 Format (Aspect 
Ratio) Press to choose the projector format.
-
12 VGA1/1 • Select the VGA1 input source.
•  Use as numeric keypad number “1”. -
13 S-Video/2 • Select the S-Video input source.
•  Use as numeric keypad number “2”. -
14 VGA2/4 • Select the VGA2 input source.
•  Use as numeric keypad number “4”. -
15 BNC/7 • Select the BNC input source.
•  Use as numeric keypad number “7”. -
16 YPbPr/8 • Select the Component input source.
•  Use as numeric keypad number “8”. -
17 OFF Turn projector OFF. 12
18 Mouse Press to switch the USB mouse on/off. -
19 Function button 
(F2) (Assignable) Programmable function button.
-
20 AV mute/Mouse 
right click • 
Press to turn off/on projector built-in speaker.
•  Use as mouse left click when mouse is switched on. -
21 Enter • Select a highlighted menu item.
•  Change or accept a value. 17
22 Re-sync Automatically synchronize the projector to the input source. -
23 V keystone/Page 
Up/Down • 
Adjust the vertical keystone.
•  Use to navigate page up or page down. 14
24 Remote ID/ 
Remote all • 
Press until Power LED is flashing then press 01~99 to set 
the particular remote code.
•  Press to set remote code to all. -
25 HDMI2 Press to choose HDMI source. -
26 HDMI1/3 • Press to choose HDMI source.
•  Use as numeric keypad number “3”. -  
						

							— 9 — 
DLP Projector — Owner’s Manual
ItemLabeLDescrIptIonsee page
27DVI/6 • Select the DVI input source.
•  Use as numeric keypad number “6”. -
28 3D/0 • Select the 3D input source.
•  Use as numeric keypad number “0”. -
29 DisplayPort/9 • Select the Display port input source.
•  Use as numeric keypad number “9”. 66-67
30 Video/5 • Select the Composite Video input source.
•  Use as numeric keypad number “5”. -
 Caution:
Use	of	controls,	adjustments	or	performance	of	procedures	other	than	those	specified	herein	may	
result in hazardous laser light exposure.
Note:
Some keys may have no function for models that do not support these feat\
ures.
Remote Control Operating Range  
The remote control uses infrared transmission to control the projector. It is not necessary to point the 
remote directly at the projector. Provided you are not holding the remote perpendicular to the front of \
the 
projector, the remote will function well within a radius of about 7 meters (23 f\
eet) and 15 degrees above 
and below the projector level or 10 degrees on the left side or right si\
de of the projector. If the projector 
does not respond to the remote control, move a little closer.
projector and Remote Control buttons 
The projector can be operated using the remote control or the buttons on\
 the rear of the projector. All 
operations can be carried out with the remote control; however, the buttons on the projector are limited in 
use.   
						

							— 10 — 
DLP Projector — Owner’s Manual
Inserting the Remote Control batteries 
1. Remove the battery compartment cover as shown in the  
illustration.
2. Insert the batteries with correct polarity (+/-) as shown inside   
the battery compartment.
3. Replace the cover.
Caution: 
•	 Only use AAA batteries (Alkaline batteries are recommended). 
•	 Dispose of used batteries according to local ordinance regulations.
•	 Remove the batteries when not using the projector for prolonged periods.\
  
						

							— 11 — 
DLP Projector — Owner’s Manual
Setup and OperatiOn 
Starting and Shutting down the projectorTurn the Projector On
1. Connect the power cord to the projector. Then connect the other end to a wall outlet.   
The Power button on the built in keypad is illuminated.
2. Remove the lens cap. 
3. Turn on the connected devices.
4. Turn on the projector by pressing “” on the remote control  
or on the built-in keypad. The Status LED is flashing Blue 
with a long blink. 
The projector splash screen displays and connected 
devices are detected.
Note:
The	first	time	the	projector	is	turned	on	you	will	be	asked	to	select	the	preferred	language,	projection	
orientation and a few other settings.
5. If more than one input device is connected, press the  Source key on the remote control to select an 
input source (VGA1, VGA2, Video, S-Video, HDMI1, HDMI2, DisplayPort, or HDBaseT).
6. The projector detects the source you selected and displays the image.   
						

							— 12 — 
DLP Projector — Owner’s Manual
Turn the Projector Off
1. Press “” on the built-in keypad or press “” on the remote control to turn off the projector. A warning 
message will appear on the displayed image.
Power Off?
Press Power key again
2. Press “” on the built-in keypad or press “” on the remote control again to confirm your selection. If 
you do not press “
” or “” again, the warning message will disappear after 15 seconds.
Caution: 
•	 The cooling fans will continue to operate for about 10 seconds for the c\
ooling cycle and the On/
Standby	LED	will	flash	Blue.	When	the	On/Standby	LED	turns	solid	red	the	projector	has	entered	
standby mode. If you wish to turn the projector back on, you must wait u\
ntil the cooling cycle has 
finished	and	the	projector	has	entered	standby	mode.	When	the	projector	is	in	standby	mode	simply	
press “
” button again to turn on the projector.
3. Disconnect the power lead from the electrical outlet and the projector.  
						

							— 13 — 
DLP Projector — Owner’s Manual
Adjusting the projector level
Take note of the following when setting up the projector:
•  The projector table or stand should be level and sturdy.
•  Position the projector so that it is perpendicular to the screen.
•  Ensure the cables are in a safe location. You could trip over them.
A
B
40 mm
1. To raise the level of the projector, lift the projector A.
2. Locate the adjustable foot you wish to modify on the underside of the pr\
ojector.
3. Rotate the adjustable foot clockwise to raise the projector or counter-c\
lockwise to lower it. Repeat with 
the remaining feet as necessary 
b.  
						

							— 14 — 
DLP Projector — Owner’s Manual
Adjusting the Zoom, Focus, and Keystone
1. Use the Zoom lever to resize the projected  
image and screen size 
b.
2. Use the Focus lever to sharpen the   
projected image 
A.
3. Use the V Keystone button to adjust the keystone Volume V Keystone
VGA11S-Video2HDMI13HDMI2
FormatZoomRemoteIDAll
VGA24Video5DVI6BNC7YPbPr8DisplayPort93D0
MenuPg
Avertically and make a squarer image A.
Note:
Horizontal keystone can only be adjusted manually.
BA  
						

							— 15 — 
DLP Projector — Owner’s Manual
projection SizeProjection Size v.s Throw Distance
EK-600U
DIagonaL 
Length(Inch)
sIze of16:10
 
screen
screen sIze W x h projectIon DIstance (D) offset (hD)
(
m) (Inch)(m)(feet)(cm)(feet)
W
IDthheIghtWIDthheIght WIDe teLeWIDe teLemaxmInmaxmIn
300.650.40 25.4 15.9 /1.4 /4.59  8.07 0.00 0.26 0.00 
40 0.860.54 33.9 21.2 1.01.93.28  6.23 10.77  0.00 0.35 0.00 
50 1.080.67 42.4 26.5 1.32.34.27  7.55 13.46  0.00 0.44 0.00 
60 1.290.81 50.9 31.8 1.62.85.25  9.19 16.16  0.00 0.53 0.00 
70 1.510.94 59.4 37.1 1.83.35.91 10.83  18.85  0.00 0.62 0.00 
80 1.721.08 67.8 42.4 2.13.76.89 12.14  21.54  0.00 0.71 0.00 
90 1.941.21 76.3 47.7 2.34.27.55 13.78  24.23  0.00 0.79 0.00 
100 2.151.35 84.8  532.6 4.78.53 15.42  26.92  0.00 0.88 0.00 
120 2.581.62 101.8  63.63.15.610.17  18.37 32.31  0.00 1.06 0.00 
150 3.232.02 127.2  79.53.97.012.80  22.97 40.39  0.00 1.33 0.00 
180 3.882.42 152.6  95.44.78.415.42  27.56 48.46  0.00 1.59 0.00 
200 4.312.69 169.6  1065.29.317.06  30.51 53.85  0.00 1.77 0.00 
250 5.383.37 212.0  132.5 6.511.621.33  38.06 67.31  0.00 2.21 0.00 
300 6.464.04 254.4  1597.814.025.59  45.93 80.77  0.00 2.65 0.00 
EK-601W
DIagonaL 
Length(Inch)
sIze of16:10
 
screen
screen sIze W x h projectIon DIstance (D) offset (hD)
(
m) (Inch)(m)(feet)(cm)(feet)
W
IDthheIghtWIDthheIght WIDe teLeWIDe teLemaxmInmaxmIn
300.650.40 25.4 15.9 /1.5 /4.92  10.09  2.02 0.33 0.07 
40 0.860.54 33.9 21.2 1.12.03.61  6.56 13.46  2.69 0.44 0.09 
50 1.080.67 42.4 26.5 1.42.44.59  7.87 16.83  3.37 0.55  0.11 
60 1.290.81 50.9 31.8 1.62.95.25  9.51 20.20  4.04 0.66 0.13 
70 1.510.94 59.4 37.1 1.93.46.23  11.15  23.56  4.72 0.77 0.15 
80 1.721.08 67.8 42.4 2.23.97.22 12.80  26.92  5.38 0.88 0.18 
90 1.941.21 76.3 47.7 2.44.47.87 14.44  30.29  6.06 0.99 0.20 
100 2.151.35 84.8  532.7 4.98.86 16.08  33.66  6.73 1.10 0.22 
120 2.581.62 101.8  63.63.35.910.83  19.36  40.39  8.08 1.33 0.27 
150 3.232.02 127.2  79.54.17.313.45  23.95  50.48 10.10  1.66 0.33 
180 3.882.42 152.6  95.44.98.816.08  28.87  60.57  12.11  1.99 0.40 
200 4.312.69 169.6  1065.49.817.72  32.15  67.31 13.46  2.21 0.44 
250 5.383.37 212.0  132.5 6.812.222.31  40.03  84.14 16.83  2.76 0.55 
300 6.464.04 254.4  1598.114.726.57  48.23 100.96  20.19 3.31 0.66   
						

							— 16 — 
DLP Projector — Owner’s Manual
Note:
•	Vertical Lens Shift values are always calculated from the Center of Proje\
ction Lens. Therefore the 
distance 5.2 cm (2.05 inch) from the Base to the Center of Projection \
Lens needs to be added to 
each Vertical Lens Shift value.
•	 Zoom ratio is 1.8x.
5.2 cm
H
D
1
3
32
Base
Wall
1. Center of projection lens.
2. Projection image while lens shift
 at the highest position.
3. Horizontal shift range: 10% H.