Eiki Projector EK-300U User Manual

							51
    (3) When DHCP is set On, IP address, Subnet, 
         Gateway and  DNS will be obtained 
         automatically, press the OK at "Set" to confirm 
         the parameters.
         When DHCP is set Off, press the OK button to 
         enter IP address, then press  button to enter 
         Subnet, Gateway and DNS respectively, 
         press the OK at "Set" to confirm the parameters.
       
Expand
  Note:
    See page 54 for usage of Network.
This function returns all setting values except 
for the User logo, PIN code lock, Logo PIN 
code lock, Lamp counter and Filter counter to 
the factory default settings.
Factory default
ENTER
192      168         1         100        
Move                          Next                            BackMENUENTER
Network setting
   DHCP                                 Off
IP address
              
  Subnet                                                   Gateway                                DNS                                                      
LAN
 Set Cancel
255      255       255         0      
 192      168         1           1       
 
192      168         1         100       
 192      168         1           1     
This function resets the counter of Lamp usage 
hours. Please be sure to reset the lamp counter 
after replacing the lamp. WARNING indicator turns 
Off and the lamp replacement icon disappears 
after reset the lamp counter
.
Press < MENU > button on the remote controller or 
on the top control panel to display the OSD menu. 
Press button to select the Expand menu, then 
press  or button.
1) Press 
 button to select [Lamp counter] 
    menu.
2) Press  button.
3)   Press 
button to select [Lamp counter reset ], 
then press  button.
4)   " Lamp replacement counter reset ? "  
conformation box appear.
5) Select "Yes" and Press  button.
Lamp Counter ResetLamp Counter Factory Default
Expend
Language
Auto setup
Keystone
Logo
Security
Power management
Filter counter
Test pattern
Network
Factory default
Lamp counter
Expend
Language
Auto setup
Keystone
Logo
Security
Power management
Filter counter
Test pattern
Network
Factory default
Lamp counter                    
						

							52
Memory viewer
The Memory Viewer function makes it possible to project the pictures which are store\
d in the USB 
memory when the USB memory is inserted into the projector
Start the slide show. Note:
● The "Memory Viewer" menu is available 
   when select the input source as "Memory  
   Viewer".
● All the setting except "Set Slide" will effective 
   after execute "Apply".
● See page 62  for Memory viewer function.
Memory Viewer menu
Set the slide transition effect when the slide 
show image is switching.
Slide down ... Switch the image from the top to 
                        the bottom.
Slide right .... .Switch the image from the left to 
                        the right.
Memory Viewer
Set slide
Slide transition effect
Sort order
Rotate
Best fit
Repeat
Apply Slide right
Name order No rotate Off
Off
Set Slide
Slide transition effect
1 Press MEMORY VIEWER button on the remote control.
2 Press MENU button on the remote control to display screen menu. Press   button to select 
   "Memory Viewer", then press the OK button.
3 Press   button to select  the item you want to set,  press the OK button.
4 Press   button to adjust the item, then press the OK button.
Set the sort order of the slide show.
Extend Order ......    Sort files or folders in 
extended order.
Size Order ..........   Sort files or folders in 
amount of data order.
Time Order .........    Sort files or folders in stored 
time order.
Name Order .......    Sort files or folders in name 
order.
Sort Order
Set the rotate direction of image.
No Rotate ........... Rotate is disabled.
270 Degrees ......  Rotate 270 degrees in 
                                                          anti-clockwise  direction.                            
180 Degrees ......  Rotate 180 degrees.
90 Degrees ........  Rotate 90 degrees in anti- 
                              clockwise direction.
Rotate
Set the image whether or not to fit with the 
projected screen.
On ...... Display the image to fit with the  
             aspect of the projected screen.
Off ...... Display in the normal pixels of the 
             image.                      
Best Fit
Enable or disable repeat funtion of the slide 
show.
On ...... Display all of the files repeatedly.
Off ...... Return to the thumbnail page after  
             the last file is broadcasted.                  
Execute the setting in slide show.
Press 
  to select "Apply", then press the 
OK button, the setting of the items except the 
"Set Slide" will be effective.
Repeat
Apply           
						

							53
Information
The information menu is used to the detect signal of projected image and\
 running state.
Menu operation
Press MENU button on the remote control or 
top control to display the screen menu. Press 
  to select  Info., the information menu will 
appear as the right picture.
The information below will display in 
information menu. info. menu
Info.
Input
H-sync freq.
V-sync freq.
Lamp status
Lamp counter
Power management
Image modeComputer 1
1024 x 768, 60Hz 48.24   kHz
60.06     Hz
2       HReady
5    Min
Standard
Input
The selected input source is displayed.
H-sync freq .
The horizontal frequency of the input signal is 
displayed in KHz or - - - -KHz when no signal is 
detected.
V-sync freq .
The vertical frequency of the input signal is 
displayed in Hz or - - - - Hz when no signal is 
detected.
Lamp status
The setting status of "Lamp control" is 
displayed.
Lamp counter
The usage time of the lamp is displayed.
Power management
The setting status of "Power management" is 
displayed. 
Image mode
The setting status of "Image mode" is 
displayed.           
						

							54
LAN control
Function : PC controls projector via LAN.Preparation:
1. Equipments: PC, projector, cables
2. Connection procedures:
    Connect the projector to routers or switches of the LAN by direct or\
 cross cable. If it fails to  
    connect PC and projector by parallel cable, please switch to cross c\
able as suggested.
3. After the computer is booted and the projector is plugged in, indicator \
lights of LAN interface 
    and computer interface will flash continuously.
Operation procedures:
   1  Turn on the projector.
   2  Obtain network address. DHCP set is displayed as on and obtain network address 
       automatically. If familiar with network, you can set DHCP as close and obtain network 
       address manually.
   3  Enter network settings menu.
       (1) Press MENU button on top control
            or remote control to display screen
            menu. Press ▲▼ button to select 
            "Expand" icon, then press the OK button.
       (2) Press ▲▼ button to select "Network"
             setting and press the OK button enter 
             the network setting.
       (3)  Press ▲▼ button to set DHCP as on. 
       (4)  Press ▲▼ button to "Set" and press
              the OK button."Please wait..." appears.
Network Control Instructions
Expend
NetworkNetwork setting
Network information
MAC address
IP address 7C 6F F8 4E 48 A8
192.168.1.100
Network setting
    DHCP                                 On
 SetCancel
IP address   Subnet 
 Gateway     DNS     
 
Move                          Next                            Back
LAN
MENUENTER           
						

							55
Network Control Instructions
6. Select "Login" to login the Network Display System page. (Both the i\
nitial name and passwords 
    are "admin".)  Note:
●  You can click the upper right corner of the web browser screen to select the display language.
●  Do not perform setting or control simultaneously by starting up multiple web browsers. Do not 
    set or control the projector from multiple computers.
●  Change the password first. (8 half-width characters). 
●  If the screen for the web control is not displayed, consult your network administrator.
7. Items in Network Display System page including: "System Status", "Gen\
eral Setup", "Picture  
    Setup", "Image Setup" and "Network Setup".
①  System Status
     The "System Status" page is displayed by  
     clicking this item.
②  General Setup
     The "General Setup" page is displayed by  
     clicking this item.
③  Picture Setup
     The "Picture Setup" page is displayed by  
     clicking this item. ④
 Image Setup
     The "Image Setup" page is displayed by  
     clicking this item.
⑤  Network Setup
     The "Network Setup" page is displayed by  
     clicking this item.
①
②
③
④
⑤
5. Enter the IP address set by the projector into the URL input field of the Web browser.
4. Activate the Web browser in the personal computer.  
						

							56
Network Control Instructions
"System Status" page
  Display the status of the projector for the following items."General Setup" page
 Change Password for Webpage is displayed.
①
②
③
①
②
③④
⑤
⑥
①  Model Name
     Displays the model No. of the projector.
②   Versions
     Displays the version of the firmware of the 
     projector.
①  Enter Old password
     Enters the configured password.
②  Enter New password
     Enters the new password.
③  Confirm New password
     Enters the wanted new password again for 
     confirmation. ④
 Apply
     Updates the settings.
⑤  Power
     Switches on/off the power of the projector.
⑥  Source Select
     Switches the input source of the projector. ③
 LAN Status
     Displays the connection status of the LAN.  
						

							57
"Picture Setup" page
① Brightness
     Adjusts the brightness of the projected image.
②  Contrast
     Adjusts the contrast of the projected image.
③  Sharpness
     Adjusts the sharpness of the projected image. ④
 Color
     Adjusts the color saturation of the projected  
     image.
⑤  Tint
     Adjusts the skin tone of the projected image.
⑥  Color Temperature
      Adjusts the color temperature of the projected 
     image.
①
②
③
④
⑤
⑥
Network Control Instructions  
						

							58
"Image Setup" page
①
②
③
④
⑤
⑥
⑦
⑧
⑩⑨
⑪
①    Aspect
     Switches the aspect of the projected image.
②  Fine sync
     Adjusts the fine sync of the projected image.
③  H Position
     Adjusts the horizontal position of the projected 
     image.
④   V  Position
     Adjusts the vertical position of the projected 
     image.
⑤  H.Size
     Adjusts the total number of dots of the 
     projected.
⑥  Freeze
     Switches the freeze function between on 
     and off. ⑦ 
Auto PC adj.
    Executes the Auto PC adj. function.
⑧  V Keystone
     Corrects the keystone in vertical direction.
⑨  H Keystone
     Corrects the keystone in horizontal direction.
⑩  Curved Correction
     Corrects the pincushion or barrel of the 
     projected image.
⑪  Corner correction
     Corrects the four corners of the projected 
     image.
Network Control Instructions  
						

							59
"Network Setup" page
8. PwPresenter software: when "Network" is selected in Source Select, yo\
u can project the current 
    computer images via network.   
  
   Input the IP address of the projector in webpage to enter the Network Display System\
, click  
   "Download" to download the PwPresenter software according to your ope\
ration system.
① LAN Setup
     Select [Obtain an IP address automatically]  
     if you want to enable the DHCP client.
      IP Address
     Enter the IP address when not using a DHCP 
     server.
      Subnet
     Enter the subnet mask when not using a 
     DHCP server.       Gateway
     Enter the default gateway address when 
     not using a DHCP server.
      DNS
     Enter the DNS server when not using a  
     DHCP server.
②    Apply
     Updates the settings.
①
②
Network Control Instructions
9. Click  icon to access the PwPresenter software.
①
②③
④ ⑤ ⑥  
						

							60
① Search for projector display    Click to enter Search, select the projector and connect it. Please setti\
ng the same IP address of 
    the projector in pwPresenter software, (such as: 192.168.1.100).  \
Both the initial name and 
    passwords are "admin".
 Note:
●  Before use PwPresenter software to search, you need change Source Select\
 to "Network".
②  Play/Pause
    Play or pause the selected image.
③  Choose capture mode
    Choose a capture mode from "FullScreen", "FixedSize" or "Alterable."
Network Control Instructions
Advanced Setting: setting image quality, 
network  port etc,.
④ 
Parameters Setting
    Basic Setting: setting language, region of   
    capture image etc,.