Eiki Projector EK-300U User Manual

							41
Setting
This function allows you to use the Key lock to 
set the security for the projector operation.
Select "Key lock" and press the OK button, 
then press  button to select the item you 
want.
 
Off  ............... Unlock.
Projector
Lock the operation of the top control. To unlock, 
use the remote control. 
Remote Control 
Lock the operation of the remote control. To unlock, 
use the top control. 
Key lock
Setting
On start
Standby mode
High land
Lamp control
Cooling fast
Closed caption
Key lock
Iris
Terminal
Sound
HDMI Setup Off
Eco Off
Normal Off
On
Computer 2
Allows the subtitle to be displayed for the 
audio contents or other information. If the input 
source contains closed caption, you can enable 
this function and change the channel. Press 
  to select Off, CC1, CC2, CC3 or CC4.
 Note:
   - The icon of Closed Caption is displayed in 
      grey when it is disable.
   - Closed caption is disable when screen menu    
     or Timer displayed on screen.
If the top control accidentally becomes locked 
and you do not have the remote control nearby or 
there is something wrong with your remote control, 
contact the dealer where you purchased the 
projector or the service center.
Closed Caption
Setting
On start
Standby mode
High land
Lamp control
Cooling fast
Closed caption
Key lock
Iris
Terminal
Sound
HDMI Setup Off
Eco Off
Normal Off
On
Computer 2
Closed Caption
Key lock                    
						

							42
This function is used to increase the contrast of 
the image.
  On .... Enable Iris function, increase the  
             contrast of the image.
  Off .... Disable Iris function.
The VGA IN 2/VGA OUT terminal can be  used 
as computer input or monitor output. Press▲ 
to select input or output.
  VGA 2 ......VGA 2 input.
  Monitor out  ....... Monitor out.
This item is used to adjust the volume.
  Sound 
   Press   button to increase the volume, press 
 button to decrease the volume. (0~25)
  Mute 
    Press ▲ button to switch mute 
function. (On/
Off) SoundIris
Terminal
Setting
On start
Standby mode
High land
Lamp control
Cooling fast
Closed caption
Key lock
Iris
Terminal
Sound
HDMI Setup Off
Eco Off
Normal Off
On
Computer 2
Setting
On start
Standby mode
High land
Lamp control
Cooling fast
Closed caption
Key lock
Iris
Terminal
Sound
HDMI Setup Off
Eco Off
Normal Off
On
Computer 2
Setting
Iris
Terminal
Sound
Setting
SoundVolume
Mute 12
Off                             
						

							43
Setting
HDMI setup
Image
64-940 ....... Select when the HDMI terminal  
                  of an external device (such as a 
                  b l u - ray player) is connected to the" 
                      HDMI" terminal.
0-1023 ......  Select when the DVI-D terminal 
                    output of an external device (such  
                    as a computer) is connected to the 
                    "HDMI" terminal via a conversion 
                    cable or similar cable. Select also 
                    when the HDMI terminal output of 
                    a computer or other device is 
                      connected to the "HDMI" terminal.
Note:
   The optimal setting varies depending on 
   the output setting of the connected external 
   device. Refer to the operation instruction of 
   the external device regarding the output of the 
   external device.
Sound
HDMI .......... Select when the HDMI cable is 
                     connected, the image and audio 
                     are transmitted, and you do not 
                     need to connect the audio signal 
                     separately.
Computer ... Select when the DVI-D terminal 
                     output of an external device (such 
                     as a computer) is connected to 
                     the "HDMI" terminal via a 
                     conversion cable or similar cable. 
                     The sound will not be transmitted, 
                     the audio signal is input to "AUDIO 
                       IN" terminal.
1 Press the MENU button to display the screen 
   menu.  Press   button to select the   
   "Setting" menu icon. Press the OK to enter  
   the submenu entry.
2 Press   button to select "HDMI setup" 
   and then press the OK button.
3 Press   button to select "Image" or 
   "Sound" to adjust.
4 Press   button to switch the item.
When the external equipment is connected to "HDMI" terminal, if the imag\
e is not projected 
properly, please switch the settings of "Image" or "Sound" in  "HDMI setup" menu\
.Setting
On start
Standby mode
High land
Lamp control
Cooling fast
Closed caption
Key lock
Iris
Terminal
Sound
HDMI Setup Off
Eco Off
Normal Off
On
Computer 2           
						

							44
Expand
The projector has Expand menu that allows you to set the other various expand functions 
described as follows.Expand menu
This projector provides multi-language screen 
menu.
You can press  button to select the language 
you want: English, German, French, Italian, 
Spanish, Polish, Swedish, Dutch, Portuguese, 
Japanese, Simplified Chinese, Traditional 
Chinese, Korean, Russian, Arabic, Turkey, 
Finland, Norway, Denmark, Indonesia, 
Hungary, Czech Republic, Kazakhstan, 
Vietnamese, Thai, Farsi.
1 Press MENU button on the remote control to display screen menu. Press 
 button to select 
   "Expand", then press the OK button.
2 Press   button to select  the item you want to set,  press the OK button.
3 Press   button to adjust the item, then press the OK button.
Language
Auto setup
Press AUTO button on the remote control to 
execute "Input search", "Auto PC adj." and 
"Auto keystone" functions.
Input search
Allows you to automatically detect input
signals. It stops when a signal is found. Press 

 button  to select an option below: 
On ........ Enabled. This function is used to    
               detect input signals automatically 
               and stops when finding a signal.
Off ........ Disabled.
Auto PC adj.
On ........ Press the AUTO button on the 
               remote control or top control to 
               enable Auto PC adj. function 
                automatically. 
Off ........ Cancel Auto PC adj. function.
Auto keystone
Auto .....  When detecting the projector is 
               tilted, correct the vertical keystone 
               in real time.
Manual ........ When pressing AUTO button on 
                      the remote control or top control, 
                      perform a vertical keystone.
Off ........ Disabled.
Note:
  - "Input search", "Auto PC Adj." and "Auto  Keystone"  
     cannot be set to "Off" at the same time. At least 
     one of them is set to "On".  
  -  Sometimes the auto keystone maybe correct 
     image imperfectly, manual keystone is required.      
  - The Auto keystone function cannot work when 
    "Display" → "Project way" is set to "Ceiling/
     Front" or "Ceiling/Rear".
Auto setup
Expend
Language
Auto setup
Keystone
Logo
Security
Power management
Filter counter
Test pattern
Network
Factory default
Lamp counter
Expend
Language
Auto setup
Keystone
Logo
Security
Power management
Filter counter
Test pattern
Network
Factory default
Lamp counter                    
						

							45
Expand
Keystone menu
This function is used to store or reset the 
keystone correction when the AC power cord is 
unplugged. 
1 Press MENU button on the remote control 
   to display screen menu. Press   button 
   to select "Expand", then press the OK button.
2 Press  button to select "Keystone", press 
   the OK button.
3 Press  button to select the item you want 
   to set, press the OK button.
Expend
KeystoneKeystone
H/V Keystone
Corner correction
Curved correction
Reset value Store
Keystone
Sets whether or not to keep the keystone 
correction after turn off the projector or plug out 
the power cord.
H/V Keystone
Adjust when the horizontal or vertical trapezoid of the projected image \
is distorted.
Store ..... The keystone correction will be kept when plug out the power cord or tur\
n off the 
                projector.
Reset .... When "Standby mode" is set to "Eco",  plug out the power cord\
 or turn off the projector, 
                the keystone correction will be canceled. When "Standby \
mode" is set to "Normal", plug 
                out the power cord, the keystone correction will be canc\
eled; turn off the projector, the 
                keystone correction will be kept.
Keystone
Corner correction
Adjust when the four corners of the projected image are distorted.
Press▲▼◄►to adjust the item.
  Note:
●  The white arrows indicate that there is no correction.
●  A red arrow indicates the direction of correction.
●  An arrow disappears at the maximum correction.
Corner correction
Upper left Upper rightLower leftLower right
Reduce the upper
width with 
 button. Reduce the left
width with 
 button. Reduce the right
width with 
 button.
Reduce the lower 
width with  
 button.           
						

							46
Expand
 Note:
● Either "H/V Keystone" , "Corner correction" or "Curved correction" setting value is valid. When 
   the "H/V Keystone" , "Corner correction" or "Curved correction" adjustment is finished, the 
   adjusted value will be reset when you adjust the other one.
● The "Curved Correction X Offset" and the "Curved Correction Y Offset" can not be adjusted 
   independently. After adjusting the "Curved Correction X/Y Gain" at the beginning, please adjust 
   the "Curved Correction X Offset" and "Curved Correction Y Offset".
● Press the KEYSTONE button on the remote control when the keystone screen is displaying  (it 
   includes: H/V Keystone, Corner correction, Curved correction and Rese\
t value), press   
   button switch to the other adjustment screen.
● Correcting up to ±30° for the tilt in the vertical direction and ±15° for the tilt in the horizontal  
   direction are available for adjustments with "Keystone". However, the image quality will degrade  
   and it will get harder to focus with more correction. Install the projector so that the correction will 
   be as small as possible.
● Screen size will also change when "H/V Keystone" is used to perform various adjustments.
● Aspect ratio of the image size may shift depending on the correction.
Curved correction (For XGA and WXGA model only)
Adjust when the linearity is not uniform or the vertical and horizontal \
lines are distorted.
Press▲▼◄►to adjust the item.
Reset value
Return the corrected values to the factory default values.
Press▲▼to select "Reset value", then press the OK button, the state of the keystone correction is 
released.
Items Operation AdjustmentAdjustment range
       Barrel 
correction  X/Y                   
        Gain Press the►button
Adjust the right of 
the width -40 ~ +40
Press the◄button Adjust the left of 
the width
Press the▲button Adjust the top of 
the width
-40 ~ +40
Press the▼button Adjust the bottom 
of the width
      Barrel 
correction  X   
      OffsetPress the►button Adjust the right of 
the distortion
0 ~ +1365
Press the◄button Adjust the left of 
the distortion
      Barrel
Correction Y
      OffsetPress the▲button Adjust the top of 
the distortion
0 ~ +799
Press the▼button Adjust the bottom 
of the distortion  
						

							47
Expand
This function allows you to customize the screen logo with Logo select, Capture, Logo PIN code 
lock and Logo PIN code change functions.
Logo Select
This function decides on the starting-up display 
from following options.
  Default .... Show the factory-set logo.
  User..........Show the image captured by user.
  Off ........... Show the countdown display only.
Capture
You can capture a projected image as start logo . 
Select "Capture" and press the OK button on 
remote control or control panel. 
Confirmation dialog box appears, select "Yes" 
to start capturing. 
Logo PIN code Lock
This function prevents an unauthorized person from changing the screen l\
ogo.
  Off ............The screen logo can be changed freely from the Logo menu.
  On ............The screen logo cannot be changed without a Logo PIN code.
If you want to change the Logo PIN code lock setting, press the OK button and the Logo PIN code di\
alog 
box appears. Enter a Logo PIN code by following the steps below.
Press OK button to enter the PIN code. Press ◄► button to select a number ,  and then press the 
OK button to enter this number, the cursor automatically move to next box. If you fixed an incorrect 
number, press MENU button to reset it again.
Repeat this step to complete entering a three-digit number.
After entering the three-digit number, the cursor automatically move to "Set", and press the OK 
button, then you can start to operate the projector.
If you entered an incorrect PIN code, the number (***) turn red, it wi\
ll be reset automatically within 
one second. Enter the correct PIN code all over again.
Logo PIN code change
You can change the Logo PIN code (three number). Press the OK button to\
 select Logo PIN 
code change. Logo Pin code dialog box appears, press ◄►button to enter the correct PIN code. 
The New Logo PIN code input dialog box appears. Set a new Logo PIN code, confirmation box 
appears, select Yes to set the new Logo Pin code.
Be sure to note the new Logo PIN code and keep it on hand. If you lost t\
he number, you could no 
longer change the Logo PIN code setting.
CAUTION:
WHEN YOU HAVE CHANGED THE LOGO PIN CODE, WRITE DOWN THE NEW PIN CODE 
IN COLUMN OF THE LOGO PIN CODE NO. MEMO ON PAGE 82, AND KEEP IT SECURELY. 
SHOULD THE LOGO PIN CODE BE LOST OR FORGOTTEN, THE LOGO PIN CODE SETTING\
 
CAN NO LONGER BE CHANGED. Logo
Logo
Expend
Language
Auto setup
Keystone
Logo
Security
Power management
Filter counter
Test pattern
Network
Factory default
Lamp counter           
						

							48
Security
Expand
This function allows you to use the PIN code 
lock and PIN code change functions to set the 
security for the projector operation.
PIN code lock
This function prevents the projector from 
being operated by unauthorized persons 
and provides the following setting options for 
security.
  Off .... Unlocked.
  On .... Enter the PIN code every time
             turning on the projector. If you
             want to change PIN code lock
             setting or PIN code, you must
             enter the PIN code. The default
             PIN code is "111".
Security
If you want to change the PIN code lock setting, press the OK button, th\
en PIN code dialog box 
appears.
Press ◄► button to select a number,  and then press the OK button to enter this number, the 
cursor automatically moves to next box. If you fixed an incorrect number\
, press MENU button to 
reset it again.
Repeat this step to complete entering a three-digit number.
After entering the three-digit number, the cursor automatically move to "Set", and press the OK 
button, then you can change the PIN code lock setting.
If you entered an incorrect PIN code, the number (***) turn red, it wi\
ll be reset automatically within 
one second. Enter the correct PIN code all over again.
PIN code changeThe PIN code can be changed to three-digit number. Press   button to select PIN code change. 
Pin code dialog box appears, Press  ◄► button to enter the correct code. The New PIN code input 
dialog box appears. Set a new PIN code.
CAUTION:
WHEN YOU HAVE CHANGED THE LOGO PIN CODE, WRITE DOWN THE NEW PIN CODE 
IN COLUMN OF THE LOGO PIN CODE NO. MEMO ON PAGE 82, AND KEEP IT SECURELY. 
SHOULD THE LOGO PIN CODE BE LOST OR FORGOTTEN, THE LOGO PIN CODE SETTING\
 
CAN NO LONGER BE CHANGED.
Expend
Language
Auto setup
Keystone
Logo
Security
Power management
Filter counter
Test pattern
Network
Factory default
Lamp counter           
						

							49
Expand
This function is used to set a frequency for filter 
cleaning.
When the projector reached a specified time 
between cleanings, a Filter warning icon 
appears on the screen, notifying the cleaning 
is necessary. After cleaning the filter, be sure 
to select RESET and set the timer. The Filter 
warning icon will not turn off until the filter 
counter is reset.
Filter counter 
Display the using time of the filter. 
Timer
Set the time to display the warning icon.
Filter counter reset
Reset the filter counter.
Filter counterFilter counter
For reducing power consumption as well as 
maintaining the lamp life, the Power management 
function turns off the projection lamp when the 
projector is not operated for a certain period. Select 
one of the following options:
Ready
When the lamp has been fully cooled down, the 
POWER indicator changes to green blinking. In this 
condition, the projection lamp will be turned on if 
the input signal is reconnected or any button on the 
remote control or top control is pressed.
Shut down
When the lamp has been fully cooled down, the power 
will be turned off.
Off 
Power management function is off.
Timer
If the input signal is interrupted and no button is 
pressed for more than 30 seconds, the timer display 
with No signal appears. It starts the countdown until 
the lamp is turned off. Press  button to set the 
Timer(1~30min.)
Ready countdown
Set the time that ready status transfers to standby 
status automatically.(0-30min. 0 Min: not transfer 
automatically)
In ready status, press POWER button to switch to 
standby status, and press any other button to turn on 
the projector.
Power management
 Note:
  Factory default: "Timer: 5 min",
   "Ready countdown: 5 min".
Power management
    No signal
  01 : 20
Time left before Lamp is off.
Expend
Language
Auto setup
Keystone
Logo
Security
Power management
Filter counter
Test pattern
Network
Factory default
Lamp counter
Expend
Language
Auto setup
Keystone
Logo
Security
Power management
Filter counter
Test pattern
Network
Factory default
Lamp counter                    
						

							50
Expand
This function is used to set the internal test 
signal: Gray scale 1, Gray scale 2, Gray scale 
3, Gray scale 4, Color bar, Red, Green, Blue, 
Cross hatch, White, Black and Raster gray.Test Pattern
Test Pattern
Function : PC controls projector via LAN.
Preparation:
1. Equipments: PC, projector, cables
2. Connection procedures:
    Connect the projector to routers or switches of the LAN by direct or\
 cross cable. If it fails to  
    connect PC and projector by parallel cable, please switch to cross c\
able as suggested.
3. After the computer is booted and the projector is plugged in, indicator \
lights of LAN interface 
    on will flash continuously.
Network
Operation procedures:
   1  Turn on the projector.
   2  Obtain network address. DHCP set is displayed as On and obtain network address 
       automatically.( If familiar with network, you can set DHCP as Off and obtain network 
       address manually.)
  3  Enter network settings menu.
    (1) Press MENU button on the remote control to 
         display screen menu. Press 
 button to
         select Expand, then press the OK button.   
    (2) Press   button to select Network, and 
         then press the OK button to enter the network 
         menu.
         MAC address ... Displays the MAC address 
                                    of wired network of this 
                                    projector.
         IP address .........Displays the IP address of 
                                    wired network of this 
                                    projector.
Network setting
    DHCP                                 On
 SetCancel
IP address   Subnet 
 Gateway     DNS     
 
Move                          Next                            Back
LAN
MENUENTER
Expend
Language
Auto setup
Keystone
Logo
Security
Power management
Filter counter
Test pattern
Network
Factory default
Lamp counter
Expend
Language
Auto setup
Keystone
Logo
Security
Power management
Filter counter
Test pattern
Network
Factory default
Lamp counter