Eiki Projector Eip Wx5000 User Manual

59
Setting the keycode
1Select “System Lock” on the “Op-
tions 1” menu, then press 
| || |
|.
•A message is displayed.
•Read this message, and press ENTER.
2Press the 4 buttons on the remote
control or on the projector to enter
the preset keycode in “Old Code”.
•When setting the keycode for the first time,
press " on the projector for four times.
Note
•If you input a wrong keycode, the cursor returns
to the first point of the “Old Code”.
•The preset keycode is 4 " buttons on the projec-
tor. If...

60
Using the “Options 1” Menu
When the system lock is set
If you have set the system lock, enter the
keycode and follow the procedure below to
release the system lock.
    ▼Input screen for keycode
Note
•When System Lock is set, the keycode input
screen appears after the power is turned on.
•If no keycode is entered, the image will not be
displayed, even if the projector receives the in-
put signal.
1Press STANDBY-ON on the re-
mote control or  on the projector to
turn on the projector.
2When the keycode...

61
Helpful Functions Set during Installation (“Options 2” menu)
1 11 1
1 Setting a Password
• •• •
•There is no factory preset for the password,
so the “Options 2” menu is enabled.
• •• •
•If you do not want others to operate the
“Options 2” menu, set a password.
1Select “Password” from the
“Options 2” menu, and press 
| || |
|.
2Press 
' '' '
' or 
" "" "
" to set the first digit in
“New Password” and then press 
| || |
|.
3Enter the remaining 3 digits and
press...

62
4 44 4
4 Reversing/Inverting
Projected Images
This projector is equipped with a reverse/invert
image function that allows you to reverse or in-
vert the projected image for various applications.
Note
•This function is used for the reversed image and
ceiling-mount setups. (See page 23.)
5 55 5
5 Controlling Multiple
Projectors with the One
Remote Control
This function allows you to control multiple projectors
with the one remote control during the stack projec-
tion or the video wall projection. When...

63
6 66 6
6 Shortcut to Make
Projector Stack Settings
Normally, settings via web browser are required for
the stack projection. You can skip the settings via
web browser by using “Pair Stack”, only when you
use the two projectors for the stack projection.
Note
•Before setting “Pair Stack”, select “Master” or
“Slave” on “Stack Setting”.
1Select “Pair Stack” on the “Option
2” menu, and then press ENTER.
•The confirmation screen will be displayed.
2Select “OK”, and then press
ENTER.
•The network settings of...

64
q qq q
q Selecting the Transmission
Speed (RS-232C)
Make sure that both the projector and computer
are set for the same baud rate.
Note
•Refer to the “SETUP MANUAL” contained on
the supplied CD-ROM for RS-232C Specifica-
tions and Command Settings.
•Refer to the computer’s owner’s manual for in-
structions for setting the computer’s baud rate.
w ww w
w Setting the Monitor
Output
When the Monitor Out has been set to “Enable”,
the monitor output is activated and power is con-
sumed even in the standby...

65
Note
•Before setting “TCP/IP”, select “OFF” for “DHCP
Client”.
•Confirm the existing network’s segment (IP ad-
dress group) to avoid setting an IP address that
duplicates the IP addresses of other network
equipment or computers. If “192.168.150.002”
is not used in a network with an IP address of
“192.168.150.XXX”, you don’t have to change
the projector IP address.
•For details about each setting, consult your net-
work administrator.
t tt t
t Setting the TCP/IP
Set the TCP/IP manually.
1Select...

66
Cleaning the air vents and the intake vent cover
■Use a vacuum cleaner to clean dust from the ex-
haust vent, the intake vents and the intake vent cover
(on the bottom of the projector).
Cleaning the projector
■Ensure the power cord is unplugged before clean-
ing the projector.
■The cabinet as well as the operation panel is made
of plastic. Avoid using benzene or thinner, as these
can damage the finish on the cabinet.
■Do not use volatile agents such as insecticides on
the projector.
Do not attach...

67
Cleaning the Dust Filters
1Press STANDBY-ON  on the pro-
jector or on the remote control
to put the projector into standby
mode.
• Disconnect the power cord and unplug
the power cord from the AC socket after
the cooling fan stops.
2Remove the filter cover.
•Remove the filter cover as shown in
the figures while pressing down the
tabs.
3Clean the dust off the dust fil-
ters and the cover with a hand
broom.
Cleaning and Replacing the Dust Filters
•The dust filters should be cleaned every 100
hours of...

68
Cleaning and Replacing the Dust Filters
4Replace the filter cover.
•Insert the filter cover as shown in the
figure and push both the two tabs until
you hear a click.
Remove
Attach
Pierced through 
the nine slits.
Insert the filter 
below the six tabs 
on both left and 
right sides.
Note
• Be sure the filter cover is securely installed.
The power will not turn on unless it is cor-
rectly installed.
Replacing the Dust Filters
After removing the filter cover (see
step 2 of “Cleaning the Dust Filters”),...