Eiki Projector Eip Wx5000 User Manual

9
Ensure that you read the following safeguards when
setting up your projector.
Caution concerning the lamp unit
■Po tential hazard of glass particles if lamp rup-
tures. In case of lamp rupture, contact your
nearest EIKI Authorized Dealer or Service
Center for replacement. See “Regarding the
Lamp” on page  71.
Caution concerning the setup of the pro-
jector
■ For minimal servicing and to maintain high
image quality, EIKI recommends that this pro-
jector be installed in an area free from hu-
midity, dust...

10
Using the projector in other countries
■The power supply voltage and the shape of
the plug may vary depending on the region
or country you are using the projector in.
When using the projector overseas, make
sure you use an appropriate power cord for
the country you are in.
Temperature monitor function
■If the projector starts to over-
heat due to setup problems or
blockage of the air vents, “
”
and “
” will illuminate in
the lower left corner of the picture. If the tem-
perature continues to rise, the...

11
Accessories
Two R-6 batteries
(“AA” size, UM/SUM-3, HP-7 or similar)
Po wer cord
*
For U.S., Canada, etc.
(6 (1.8 m))
 F
or Europe, except U.K.
(6 (1.8 m))

*Use the power cord that corresponds to the wall outlet in your country.
•Projector manual and technical
reference CD-ROM
• Owner’s man ual (this manual)
(1)
(2)
Lens cap
 (Only supplied with EIP-WX5000)
Dustproof cap
(Only supplied with EIP-WX5000L)
Supplied accessories
RGB cable
(10 (3.0 m))
 Remote receiver

Remote control
■ Lamp unit AH-55001...

12
Accessories
Optional lenses
No lens is attached to EIP-WX5000L. The standard zoom lens is attached to EIP-WX5000.
The optional lenses from EIKI are also available for specialized application. Please see your
nearest EIKI Authorized Dealer for details on all the lenses. (Refer to the lens owner’s manual
when using a lens.)
Throw Distance
The graph below is for 100-inch (254 cm) screen with 16:10 normal mode.
Screen
5101520253035 455040 (ft)
Standard zoom lens (AH-55501 : Standard equipment with...

13
30
69
69
55
72
69
55
16
66
77
69
30
77
28
31
31
54
41
3032
36
47
36
47
47
47
SHUTTER buttons • OPEN : For opening the shutter.
  • CLOSE : For closing the shutter
 and hiding the projected image.
Lamp unit cover
Attaching the lens cap/dustproof capSnap on the lens cap/dustproof cap 
straight.
Removing the lens cap/dustproof capPull the lens cap/dustproof cap directly 
outward.
ZOOM buttonsFor adjusting the projected 
image size.
FOCUS buttonsFor adjusting the focus.
Power indicator
H&V LENS SHIFT...

14
Part Names and Functions
Projector (Rear View)
Using the Kensington Lock
• This projector has a Kensington Security Standard connector for use with a Kensington MicroSaver Security
System. Refer to the information that came with the system for instructions on how to use it to secure the
projector.
Numbers in  refer to the main pages in this o wner’s manual where the topic is explained.
17
26
28
Remote control sensor16
24
25
24
25
67
68
24
25
24
25
27
27
26
26
COMPUTER/COMPONENT 2 
terminals
BNC...

15
Remote Control
31
17
47
30
31
36
54
17
39
28
41
18
32
37
41
36
37
38
38
18•4718•47
LIGHT buttonFor lighting all buttons on the 
remote control.
STANDBY-ON buttonFor turning the power on or
putting the projectorinto standby mode.
ZOOM buttonsF or adjusting the projected image size.
KEYSTONE buttonFor entering the Keystone 
Correction mode.
MAGNIFY (enlarge/reduce) buttonsFor enlarging/reducing part of the image.
COMPUTER 1/2, DVI, HDMI, 
VIDEO, S-VIDEO buttons
For switching to the respective 
input...

16
Using the Remote Control
Inserting the Batteries
1Press the tab and lift open the battery
cover in the direction of the arrow
.
2Insert the batteries.
•Insert the batteries making sure the po-
larities correctly match the 
 and 
marks inside the battery compartment.
3Insert the tabs on the end of the
battery cover into their slots and
press the cover into position.
Incorrect use of the batteries may cause them to leak or explode. Please follow the precautions below.
 Caution
• Danger of explosion if...

17
Using the Remote Control with a Signal Cable
When the signals from the remote control cannot be reached due to the positioning of the projector, use a
ø3.5 mm minijack cable to connect the remote control to the projector. Now you can control the projector
with the remote control.
Note
•The wireless remote function is not possible when the ø3.5 mm minijack cable is connected to the projec-
tor. Should the wireless remote operation be required, the ø3.5 mm minijack cable should be discon-
nected from...

18
Using the Remote Control as a Wireless Computer Mouse
When connecting the supplied remote re-
ceiver to the computer, you can use the re-
mote control as the wireless computer
mouse.
1Connect the supplied remote re-
ceiver to the USB terminal on the
computer.
2Slide the ADJ./MOUSE
switch on the remote con-
trol to the MOUSE position.
3Use the mouse function.
• P oint the remote control at the remote
receiver.
■ When moving the cursor
Press  '/" /\ /| .
■ When left-clicking
Press  L-CLICK .
■...