Eiki Projector Eip Sxg20 User Manual

							41
Select Digital zoom +. The On-Screen Menu disappears and 
“D. zoom +” appears. Press the SELECT button to expand the 
image size. Use the Point ed7 8 buttons to pan the image. 
The Panning function can work only when the image is larger 
than the screen size.
You can also enter the Digital zoom + mode by pressing the 
D.ZOOM button on the remote control.Digital zoom +
Select Digital zoom –. The On-Screen Menu disappears and 
“D.zoom –” appears. Press the SELECT button to compress the 
image size. 
You can also enter the Digital zoom – mode by pressing the 
D.ZOOM button on the remote control.
To exit the Digital Zoom +/– mode, press any button except the 
D.ZOOM , SELECT, and Point buttons. Digital zoom –
For zooming in and out the images
Keystone
This function is used to store or reset the keystone correction 
when the Main On/Off Switch is pressed to Off or the AC 
power cord is unplugged. Use the Point 7 8 buttons to switch 
between each option. 
  Store . . .  Keep the keystone correction even when the Main 
On/Off Switch is pressed to Off or the AC power 
cord is unplugged.
  Reset  . .   Release the keystone correction when the Main On/
Off Switch is pressed to Off or the AC power cord is 
unplugged.
To correct keystone distortion, press the SELECT button. The 
Keystone dialog box appears. Use the Point ed7 8 buttons to 
correct keystone distortion. (p.31)
Ceiling 
Rear 
Ceiling
When this function is set to “On,” the picture is top/bottom and 
left/right reversed. This function is used to project the image 
from a ceiling-mounted projector.
Rear
When this function is set to “On,” the picture is left/right 
reversed. This function is used to project the image from the 
rear of the screen.
Reset
This function returns all adjusted values to the factory default 
settings. Press the SELECT button at Reset to display a 
confirmation box. To reset, press the SELECT button at “Yes.”
SCREEN MENU
Move the red frame pointer to the desired 
function and press the SELECT button.
Computer Input
Exit the Screen Size Adjustment Menu. Quit
✔Note:
• 
The panning function may not operate properly if 
the stored Mode in the PC Adjust Menu is used. 
(p.38)
•  The minimum compression ratio can be limited 
depending on the input signal or when the 
Keystone function is working or when the custom 
is selected for the screen size.
•  Digital zoom +/– cannot be selected when Full 
screen or True is selected. 
						

							42
AV SySTEM MENU (VIDEO OR S-VIDEO)
AV S ySTEM MENU (COMPONENT VIDEO)
Video System Selection
Press the MENU button to display the On-Screen Menu. 
Use the Point 7 8 buttons to move the red frame pointer 
to the AV System Menu icon.
Use the Point ed buttons to move the red arrow pointer 
to the desired system and then press the SELECT button.1
2
If the projector cannot reproduce proper video image, select 
a specific broadcast signal format from among PAL, SECAM, 
NTSC, NTSC 4.43, PAL-M, and PAL-N. PAL/SECAM/NTSC/NTSC4 .43/PAL-M/PAL-N
The projector automatically detects an incoming video signal, 
and adjusts itself to optimize its performance.
When the Video System is 1035i or 1080i, select the system 
manually.
If the projector cannot reproduce proper video image, select a 
specific component video signal format from among 480i, 575i, 
480p, 575p, 720p, 1035i, 1080p, and 1080i. Auto
COMPONENT VIDEO SIGNAL FORMAT
Video Jack or S-Video Jack
y, Pb/Cb, Pr/Cr Jacks
The projector automatically detects an incoming video system, 
and adjusts itself to optimize its performance. Auto
AV System Menu icon
The selected system is displayed
Move the pointer to the desired 
system and press the SELECT button.
AV System Menu icon
The selected system is displayed.Move the pointer to the desired 
system and press the SELECT button.
Video Input
✔Note:
•   
The AV System menu cannot be selected when 
selecting RGB(Scart). 
						

							43
Press the MENU button to display the On-Screen Menu. 
Use the Point 7 8 buttons to move the red frame pointer 
to the Image Select Menu icon.1
2
Use the Point ed buttons to move the red frame pointer 
to the desired image level and then press the SELECT 
button.
IMAGE SELECT MENU
Image Level Selection
Move the red frame pointer to the desired 
level and press the SELECT button.Image Select Menu icon
Normal picture level preset on the projector.
Standard
Picture level adjusted with fine tone. Cinema
Menu Operation
Video Input
Press the IMAGE SEL. button on the remote control to 
select the desired image level.
Direct Operation
Remote Control
IMAGE SEL .
 
buttonStandard
Cinema
DICOM
Dynamic
DICOM
For viewing contrasty images in a bright room.
Dynamic
User preset picture adjustment in the Image Adjust Menu. 
(p.48)IMAGE 1–10
For DICOM Part 14 grayscale standard compliant images. Image1
Image 10
•
•
•
✔Note:
 
•   DICOM stands for Digital Imaging and 
Communications in Medicine. 
						

							44
Screen Size Adjustment
Press the MENU button to display the On-Screen Menu. 
Use the Point 7 8 buttons to move the red frame pointer 
to the Screen Menu icon.
Use the Point ed buttons to move the red frame pointer 
to the desired function and then press the SELECT 
button.1
2SCREEN MENU
Provide the image at the normal video aspect ratio of 4:3. Normal
Move the red frame pointer to the desired 
function and press the SELECT button. Screen Menu icon
✔Note:
• 
When no signal is detected, “Normal” is 
set automatically and the Aspect dialog box 
disappears.
•  The adjustable range for Scale H/V and Position 
H/V is limited depending on the input signal.
Press the SELECT button at Common or 
Reset, to display a confirmation box.
Video Input
  Scale H/V ..............  Adjust the Horizontal/Vertical screen scale.
  H&V ......................  When set to “On,” the aspect ratio is 
fixed. The “Scale V” appears dimmed and 
becomes unavailable. Adjust “Scale H,” 
then the screen scale is automatically 
modified based on the aspect ratio. 
  Position H/V ..........  Adjust the Horizontal/Vertical screen 
position.
  Common ..............  Save the adjusted scale to all the inputs. 
Press the SELECT button at Common to 
display a confirmation box. To save the 
scale, press the SELECT button at “Yes.” 
When Custom is selected, the saved scale 
is used.
  Reset ....................  Reset the all adjusted values. Press 
the SELECT button at Reset to display 
a confirmation box. To reset, press the 
SELECT button at “Yes.”
Custom
Adjust the screen scale and position manually with this 
function.
Press the SELECT button at Custom and the “Custom” is 
displayed on the screen for a few seconds. To display the 
Aspect dialog box, press the SELECT button at Custom again 
and then the Aspect dialog box appears. Provide the image at the wide screen ratio of 16:9.
Wide
✔Note:
 
• Wide cannot be operated when “720p,” “1035i,” 
“1080i”, or “1080p” is selected on AV System 
Menu (p.42). 
						

							45
Keystone
This function is used to store or reset the keystone correction 
when the Main On/Off Switch is pressed to Off or the AC 
power cord is unplugged. Use the Point 7 8 buttons to switch 
between each option. 
  Store . . .  Keep the keystone correction even when the Main 
On/Off Switch is pressed to Off or the AC power 
cord is unplugged.
  Reset  . .   Release the keystone correction when the Main On/
Off Switch is pressed to Off or the AC power cord is 
unplugged.
To correct keystone distortion, press the SELECT button. The 
Keystone dialog box appears. Use the Point ed7 8 buttons to 
correct keystone distortion. (p.31)
Ceiling 
Rear 
Ceiling
When this function is set to “On,” the picture is top/bottom and 
left/right reversed. This function is used to project the image 
from a ceiling-mounted projector.
Rear
When this function is set to “On,” the picture is left/right 
reversed. This function is used to project the image from the 
rear of the screen.
Reset
This function returns all adjusted values to the factory default 
settings. Press the SELECT button at Reset to display a 
confirmation box. To reset, press the SELECT button at “Yes.”
SCREEN MENU
Move the red frame pointer to a function and 
press the SELECT button.
Video Input
Exit the Screen Size Adjustment Menu. Quit 
						

							46
Press the MENU button to display the On-Screen Menu. 
Use the Point 7 8 buttons to move the red frame pointer 
to the Image Adjust Menu icon.1
2
Use the Point ed buttons to move the red frame pointer 
to the desired item and then press the SELECT button 
to display the adjustment dialog box. Use the Point 7 8 
buttons to adjust the setting value.IMAGE ADJUST MENU
Press the Point 7 button to decrease contrast; press the Point 
8 button to increase the contrast (from 0 to 63).
Press the Point 7 button to decrease the brightness; press the 
Point 8 button to increase the brightness (from 0 to 63). Contrast
Brightness
Press the Point 7 button to decrease the intensity of the color; 
press the Point 8 button to increase the intensity of the color 
(from 0 to 63).
Press the Point 7 8 buttons to adjust the tint value to obtain 
proper color balance (from 0 to 63). Color 
✽
Tint  ✽
Color Management
The Color Management function can be used to adjust the 
LEVEL, PHASE, and GAMMA of the selected display colors 
(except for black, white, and gray) on the screen and replace 
these colors with other colors if required.
You can store up to eight (8) color management data.
1Use the Point ed buttons to move the red frame pointer 
to Color Management, and then press the SELECT 
button. The projected image freezes, and the COLOR 
MANAGEMENT POINTER appears.
Use the Point ed7 8 buttons to move the pointer to the 
spot where you want to adjust the color and then press 
the SELECT button. The COLOR SELECTION window 
appears, and the color in the center of the pointer is 
selected and you can adjust the color.
2
Use the Point ed7 8 buttons to adjust the LEVEL and 
PHASE of the color, and then press the SELECT button 
to confirm the setting. Then use the Point ed buttons to 
adjust the GAMMA for the color and press the SELECT 
button to accept the setting. After adjusting, press the 
SELECT button to go to the COLOR MANAGEMENT LIST.3
COLOR MANAGEMENT 
POINTER
POINTER MODE
Image Adjustment
Move the red frame pointer to the desired 
item and then press SELECT button. Image Adjust Menu icon
Use the Point 7 8 buttons to adjust the 
setting value.
COLOR SELECTION MODE
Go to the COLOR MANAGEMENT LIST. LIST
Picture Image
✔Note:
  ✽ Displayed in grayout in the computer Input.
• 
Tint cannot be selected when the video 
system is PAL, SECAM, PAL-M, or PAL-N 
(p.42).
•  Color management is displayed in grayout 
when there is no signal. 
						

							47
Auto picture control
Use the Point 7 8 buttons to select the desired Auto picture 
control position (Off, L1 or L2).
  Off  . . . .   Auto picture control OFF position.
  L1 . . . . .   Auto picture control LEVEL 1 position.
  L2 . . . . .   Auto picture control LEVEL 2 position.
Clear the check mark if you do not want to apply the 
adjusted color data; select the check mark and then press 
the SELECT button. The check mark disappears. Return to the COLOR MANAGEMENT POINTER. (If you 
press the MENU button on the side control or the remote 
control, it returns to the COLOR MANAGEMENT POINTER 
and you will need to reselect and readjust the color.)
Return to the IMAGE ADJUST Menu. Any settings that 
have been changed will not be stored. To store the 
changed settings, be sure to select “LIST” and go to the 
COLOR MANAGEMENT LIST.
LIST MODE
Return to the COLOR SELECTION mode so that you can 
readjust the setting for the color in that line. (This option is 
not available if the check mark is cleared.)
Select the DEL box if you want to delete the adjusted 
data. Press the SELECT button and a confirmation box 
appears and then select [Yes]. 
Delete all the data in the list. Press the SELECT button and 
a confirmation box appears and then select [Yes].
The same function as stated above.
Level and phase 
adjustment palette.
Gamma 
adjustment palette.
Color temp .
Use the Point 7 8 buttons to select the desired Color temp. 
level (XLow, Low, Mid, or High).  COLOR M .
MENU
COLOR PALETTE
DEL
ALL DEL
COLOR M .
LISTCOLOR M .MENU
COLOR PALETTE
DEL
ALL DELMENUCOLOR M .
COLOR SELECTION MODE
LIST MODECOLOR SELECTION MODE (continued)
In the COLOR MANAGEMENT LIST, the adjusted color 
data are checkmarked. You can decide whether or not to 
apply the adjusted color data in the list to the projected 
image (see below).4
MENU
The same function as stated above.
Picture Image
BrilliantColor
Set to ‘On‘ to achieve a wider range of color reproduction and 
increase the brightness of the halftone. Use the Point 7 8 
buttons to select from (Off/On).
✔Note:
•  Auto picture control is fixed to ‘Off’  when 
‘DICOM‘ is selected in the Image level 
selection (pp.39, 43).
•  W hen ‘DICOM‘ is selected in the Image level 
selection, you can select the Color temp. level 
from Blue base, Clear base, High, Mid, Low, 
or XLow (pp.39, 43).
•  Color temp.  will be displayed in grayout when 
‘Dynamic‘ is selected in the Image level 
selection (pp.39, 43). 
						

							48
Use the Point 7 8 buttons to adjust the gamma value to obtain a 
better balance of contrast (from 0 to 15).Gamma
Press the Point 7 button to decrease the sharpness of the image; 
press the Point 8 button to increase the sharpness of the image 
(from 0 to 31).
Sharpness
An interlaced video signal can be displayed in progressive mode. 
Press the Point 7 8 buttons to change the progressive scan mode. 
  Off  . . . .   Progressive scan mode is “Off.”
  On  . . . .   Progressive scan mode is “On.”
  Film  . . .   For watching a film. With this function, the projector 
reproduces pictures faithful to the original film quality.
Noise interference on the screen can be reduced. Press the Point 
7 8 buttons to change the noise reduction mode.
 
Off  . . . .   Noise reduction mode is “Off”
  On  . . . .   Noise reduction mode is “On”
Noise reduction 
✽
Progressive  ✽
Store icon
Press the SELECT button at this 
icon to store the adjustment.
Press the Point 7 button to lighten red/green/blue tone; press the 
Point 8 button to deepen red/green/blue tone (from 0 to 63). White balance (Red/Green/Blue)
Press the Point 7 button to lighten red/green/blue tone of the 
black level of an image; press the Point 8 button to deepen red/
green/blue tone of the black level of an image (from 0 to 63). Offset (Red/Green/Blue)
Exit the Image Adjust Menu. To store the adjusted data, move the red frame pointer to the 
Store icon and press the SELECT button. The Image Level Menu 
appears. Move the red arrow pointer to any of the Image 1 to 
10 in which you want to set and press the SELECT button. A 
confirmation box appears and then select [Yes]. To reset the adjusted data, select Reset and press the SELECT 
button. A confirmation box appears and then select [Yes]. All 
adjustments will return to their previous figures. Reset
Store
Quit
Press the SELECT button at this icon to 
display other items.
Press the SELECT button at this 
icon to display the previous items.
Press the Point 
7 8 buttons to 
adjust the setting value.
Picture Image
Image Level Menu
Move the red frame pointer 
to an image item to be set 
and then press the SELECT 
button.
✔Note:
   ✽ Displayed in grayout in the computer Input.
•  When  the  Color  matching  function  is  set  to  ‘On’  and 
the White  balance  Red,  Green,  or  Blue  is  adjusted,  the 
Color temp. level will change to “Adj.”
•  ‘Sharpness’  is  fixed  to  the  default  value  when  ‘DICOM‘ 
is selected in the Image level selection. • 
Progressive  cannot  be  selected  when  “480p,”  “575p,” 
“720p”, or “1080p” is selected (p.42).
•  Noise  reduction  cannot  be  selected  with  the  computer 
input and when the video signal format is 1080p.
✔Note:
 •Picture is distorted at the moment of On/Off /Film switching.  
						

							49
Picture Image
Press the MENU button to display the On-Screen Menu. 
Use the Point 7 8 buttons to move the red frame pointer 
to the Setting Menu icon.1
2
Language
The language used in the On-Screen Menu is available in 
English, German, French, Italian, Spanish, Portuguese, Dutch, 
Swedish, Russian, Chinese, Korean, or Japanese. Use the Point ed buttons to move the red frame pointer 
to the desired item and then press the 
SELECT button. 
The Setting dialog box appears.
Press the SELECT button at 
Language, then the Language 
Menu appears.
SETTING MENU (Language)
This projector has a Setting menu that allows you to set up other various functions.
Setting
Set the red frame pointer 
to the item and press the 
SELECT button. Setting Menu icon
When this function is set to “On,” the value adjustment bar in 
the Picture Image Adjustment Menu appears on the screen.
Simple menu
Menu
This function is used to adjust the On-Screen Menu display 
position. Press the SELECT button and the adjustment 
screen appears (arrows appear). Use the Point ed7 8 
buttons to adjust the position. After making the adjustment, 
press the SELECT button to return to the Menu screen.
Position
This function allows you to adjust the position and size of the 
On-Screen Display and the value adjustment bar in the Picture 
Image Adjustment Menu.
Display
This function decides whether to display On-Screen Displays.
  On  . . . . . . . . . . . .  Show all the On-Screen Displays. Use this 
function when you want to project images 
after the lamp becomes bright enough. The 
factory default setting is in this option.
  Countdown Off . . . Show the input image instead of the 
countdown when turning on the projector. 
Use this function when you want to project 
the image as early as possible even when 
the lamp is not bright enough. 
  Off  . . . . . . . . . . . .  Hide the On-Screen Displays except:
      l On-Screen Menu
    l “Power off?” (p.25)
    l Color management operation screen 
(pp.46-47)
    l “No signal” for Power management (p.57)
    l P-TIMER (p.31)
    l ”Please wait....” for Auto PC adjustment 
(p.36)
    l
 Arrows for panning mode
    l
 Warnings for lens and color wheel 
installations.
Menu
Set the red frame pointer 
to the item and press the 
SELECT button.
Setting
You can enlarge the size of On-Screen display to two times 
the normal size. Use the Point 
7 8 buttons to select from 
(Normal/Double).
Menu size 
						

							50
Background
The selected background screen will be displayed when no 
input signal is detected.
  Blue  . . .   Blue colored background.
  User  . . .   The image you captured.
  Black . . .  Black colored background.
Setting
Lamp control
This function allows you to change brightness of the screen.
2-Lamps. .   Two lamps turn on.
Lamp1
  . . .    Only Lamp1 turns on.
Lamp2
  . . .    Only Lamp2 turns on.
This projector is equipped with 2 projection lamps and the 
number of using lamps can be switched to 2 lamps or 1 lamp. 
Using 1 lamp maintains the life of projection lamps.
Press the SELECT button at Lamp mode to display a dialog 
box. Use the Point ed buttons to select "2-Lamps", "Lamp1" or 
"Lamp2" and press the SELECT button. Then the confirmation 
message appears. Select [Yes] and press the SELECT button.✔Note:
•   When  switching  from  one  of  lamps  to  the  other 
(e.g. when switching from Lamp1 to Lamp2), both 
lamps  will  light  until  the  brightness  of  the  lamps 
are stabilized.
•    When  neither  of  the  two  lamps  is  lighted,  the 
projector will shutdown automatically.
•    When  either  of  the  two  lamps  does  not  light  up, 
the  LAMP  1/2  REPLACE  indicator  blinks  orange 
and the projector will light the other automatically. 
(X  mark  will  appear  on  the  unlighted  lamp  in  the 
Lamp Status Display. See page 65 for details.)
Lamp mode
✔Note:
• 
“User” cannot be selected when the image is not 
captured.
Lamp control
Select the lamp operation when the total lighting time of a 
lamp exceeds the recommended total hours of use. 
Mode 1 . . .   A lamp can be turned on even after exceeding 
the recommended total hours of use.
Mode 2 . . .   A lamp is not turned on after exceeding the 
recommended total hours of use.
Lamp life control
✔Note:
•   
The  fan  noise  becomes  louder  in  Eco  2  than  in 
Eco  1.  Select  the  suit able  mode  for  the  used 
environment.
✔Note:
•   If  Mode  2  has  been  selected  and  either  of  two 
lamps  exceeded  its  recommended  total  hours 
of  use,  Lamp  interval  mode  will  be  fixed  to  ‘Off’. 
Also,  ‘2-Lamps’  icon  in  the  Lamp  mode  and  the 
icon  of  lamp  which  exceeded  its  recommended 
total hours of use will be displayed in grayout.
•   If  Mode  2  has  been  selected  and  both  lamps 
exceeded  the  recommended  total  hours  of  use, 
the  warning  icon  will  be  displayed  at  the  time  of 
power-on. Then  the  projector  will  turn  off  after  3 
minutes.
Lamp interval
✔Note:
•   
When either of the two lamps is out, the projector 
will  light  the  other  automatically  even  if  'Off'  is 
selected.
•    W h e n   ‘A U TO ’   i s   s e l e c t e d ,   t h e   p r o j e c t o r 
automatically  detects  which  lamp  is  used  less 
often  than  the  other  at  the  time  of  power-on  and 
lights it.
•    The  setting  values  of  time  inter val  may  not  be 
accurate, and should be used only as a guide. 
This  function  can  be  used  to  automatically  switch  the  lamp 
that  is  turned  on  after  a  certain  period  of  time  in  order  to 
reduce  the  lamp  deterioration  when  'Lamp1'  or  'Lamp2'  has 
been selected in 'Lamp mode' setting.
Use the Point 
7 8 buttons to select from (Off/Auto/24H/
200H/500H/1000H/2000H).
Normal  . . .   Normal brightness. 
Eco 1 . . . . .    Lower brightness and Fan speed decrease. 
Lower brightness reduces the lamp power 
consumption and extends the lamp life.
Eco 2 . . . . .    Lower brightness and Fan speed increase. 
Lower brightness reduces the lamp power 
consumption and extends the lamp life. It is 
recommended to use Eco 2 when using the 
projector continuously over a long period of 
time.