Eiki Projector Eip 5000 User Manual

79
Auto Power Off Function
Menu operation  Page 56
Example: “Options (1)” screen menu for
INPUT 1 (RGB) mode
Description of Auto Power Off
Note
•When “Auto Power Off” is set to “ON”, 5 min-
utes before the projector enters the standby
mode, the message “Enter STANDBY mode in
X min.” will appear on the screen to indicate
the remaining minutes.
Description
The projector automatically enters the
standby mode when no input signal is
detected for 15 minutes or longer.
The “Auto Power Off” function will be...

80
Using the “Options (1)” Menu
Note
•If you input a wrong keycode, the cursor returns
to the first point of the “Old Code”.
• The preset keycode is 4  " buttons on the projec-
tor. If this keycode is set, the keycode input screen
does not appear when turning the power on.
3Press the 4 buttons on the remote
control or on the projector to enter
the new keycode in “New Code”.
Note
• You cannot use the following buttons for
keycode:
• STANDBY-ON button
• ENTER button
• L-click button
• R-click/UNDO...

81
When the system lock is set
If you have set the system lock, enter the
keycode and follow the procedure below to
release the system lock.
    ▼Input screen for keycode
Note
•When System Lock is set, the keycode input
screen appears after the power is turned on.
• If no keycode is entered, the image will not be
displayed, even if the projector receives the in-
put signal.
1Press  on the remote control or
 on the projector to turn on the
projector.
2When the keycode input screen ap-
pears, enter the...

82
Helpful Functions Set during Installation (“Options (2)” menu)
Setting a Password
•
• •
•
•There is no factory preset for the password, so
the “Options (2)” menu is enabled.
•
• •
•
•If you do not want others to operate the “Op-
tions (2)” menu, set a password.
Menu operation  Page  58
Example: “Options (2)” screen menu
1Select “Password” from the “Op-
tions (2)” menu, and press 
|
| |
|
| .
2Press 
'
' '
'
'  or 
"
" "
"
"  to set the first digit in
“New...

83
Checking the Lamp Life
Status
You can confirm the cumulative lamp usage time
and the remaining lamp life (percentage).
Menu operation  Page 56
Example: “Options (2)” screen menu
Description of Lamp Timer (Life)
* This is a reference value and is not guaranteed.
Note
•It is recommended that the lamp be changed
when the remaining lamp life becomes 5%.
• The table  above indicates rough estimates in the
case of using only in each mode shown.
• The lamp life may vary depending on the usage
condition.
Lamp...

84
Reversing/Inverting Pro-
jected Images
This projector is equipped with a reverse/invert
image function that allows you to reverse or in-
vert the projected image for various applications.
Menu operation  Page 58
Example: “Options (2)” screen menu
Description of PRJ Modes
Note
•This function is used for the reversed image and
ceiling-mount setups. (See page  23.)
Description
Normal image
Inverted image
Reversed image
Reversed and inverted image
Selectable items
Front
Ceiling + Front
Rear
Ceiling +...

85
Master Slave
IP Address 192.168.150.2 192.168.150.3
Subnet Mask 255.255.255.0 255.255.255.0
DHCP Client OFF OFF
Gateway0.0.0.0 0.0.0.0
User Name (Reset) (Reset)
Password (Reset) (Reset)
Data Port 10002 10002
Shortcut to Make Projector
Stack Settings
Normally, settings via web browser are required for
the stack projection. You can skip the settings via
web browser by using “Pair Stack”, only when you
use the two projectors for the stack projection.
Menu operation  Page  56
Note
•Before setting “Pair...

86
Helpful Functions Set during Installation (“Options (2)” menu)\
Bypassing Unused Input
Selections
This function allows you to skip the input mode
that you rarely use. You can skip the input modes
when pressing INPUT 1, 2, 3 button or INPUT 4, 5
button on the projector.
Menu operation  Page 58
Example: “Options (2)” screen menu
Description of Set Inputs
Selecting the Fan Mode
This function changes the fan rotation speed.
Menu operation  Page  58
Example: “Options (2)” screen menu
Description of Fan...

87
Selecting the Transmis-
sion Speed (RS-232C)
Make sure that both the projector and computer
are set for the same baud rate.
Menu operation  Page 58
Example: “Options (2)” screen menu
Description of RS-232C
Note
•Refer to the “SETUP MANUAL” contained on
the supplied CD-ROM for RS-232C Specifica-
tions and Command Settings.
• Refer to the computer owner’s manual for in-
structions for setting the computer’s baud rate.
Direct Power On Function
Menu operation  Page  56
Example: “Options (2)” screen menu...

88
Monitor Output Settings
When the Monitor Out has been set to “Enable”,
the monitor output is activated and power is con-
sumed even in the standby mode. It is recom-
mended that the Monitor Out be set to “Disable”
when it is not connected. This reduces power
consumption when the projector is in the standby
mode.
Menu operation  Page 58
Example: “Options (2)” screen menu
Description of Monitor Out
Description
The monitor output function is activated
even if the projector is in standby mode.
The monitor...