Eiki Lc-Xt9 Multimedia Projector Owners Manual

51
APPENDIX
COMPATIBLE COMPUTER SPECIFICATIONS
–––––––– (Interlace)
1024 x 768 (Interlace)
ON-SCREEN
DISPLAYRESOLUTIONH-Freq.(kHz)V-Freq. (Hz)
VGA 1640 x 48031.4759.88
VGA 2720 x 40031.4770.09
VGA 3640 x 40031.4770.09
VGA 4640 x 48037.8674.38
VGA 5640 x 48037.8672.81
VGA 6640 x 48037.5075.00
MAC LC13640 x 48034.9766.60
MAC 13640 x 48035.0066.67
MAC 16832 x 62449.7274.55
MAC 191024 x 76860.2475.08
MAC 211152 x 87068.6875.06
45.0060.00
SVGA 1800 x 60035.15656.25
SVGA 2800 x 60037.8860.32
SVGA 3800 x...

52
APPENDIX
OPTIONAL PARTS
The parts listed below are optionally supplied.  When ordering those par\
ts, give the name and Type No. to the sales dealer.
●DVI Board (HDCP Compatible) Type No. : AH-72003
● 5 BNC Board Type No. : AH-72015
● Video/Y,C & S-Video Board Type No. : AH-72023
● D-Sub 15 Board Type No. : AH-72031
● Network Board Type No. : AH-72142                                                                \
             
● Dual SDI Board Type No. : AH-72162
● Warp & Blending Board Type No. :...

53
APPENDIX
Owner’s Manual (CD-ROM)
Quick setup manual
AC Power Cord
Wireless/Wired Remote Control Transmitter and Batteries
VGA Cable
6 Types Light-Block Sheet (For option lens)
2 Types Lens Attachment (For option lens)
Real Color Manager ProAccessories
TECHNICAL SPECIFICATIONS
1.8 TFT Active Matrix type, 3 panels
Multi-media Projector
80.3 lbs (36.5 kg)
22.9 x 10 x 30.9 (581 mm x 252 mm x 783 mm) 
1024 x 768 dots
2,359,296 (1024 x 768 x 3 panels)
PAL, SECAM, NTSC, NTSC4.43, PAL-M and PAL-N (With option...

54
APPENDIX
Vcc
- Data
+ Data
Ground
1
2
3
4
USB PORT TERMINAL
Pin Configuration
Connect USB port output terminal of computer
or peripheral equipment to this terminal with
USB port  Cable (not supplied).
2
34 1
CONFIGURATIONS OF TERMINALS
HDB 15-PIN TERMINAL (ANALOG)
Connect display output terminal of computer to this terminal with VGA Ca\
ble (supplied).
512341096781514131112
Red Input
Ground (Horiz.sync.)
Green Input
Sense 2
Blue Input
Ground (Red)
Ground (Green)
Ground (Blue)
1
5
2
4
3
6
7
8
+5V...

55
APPENDIX
DIMENSIONS
22.87 (581.0)
Unit : inch (mm)Screw Holes for Ceiling Mount
Screws: 9-M8
Depth: 0.315 (8.0)
9.90 (251.5)10.15 (258.0)
5.18 (131.5)
9.90 (251.5)
5.7 °
2.36 (60.0)
30.83 (783.0)
17.56 (446.0)
22.87 (581.0)
9.25 (235.0)
8.62 (219.0) 17.56 (446.0)
7.01 (178.0) 7.01 (178.0)
4.23 (107.5)
3.26 (82.8)
9.72 (247.0)
14.74 (374.5)
6.81 (173.0) 1.38 (35.0)
1.57 (40.0)
8.27 (210.0) 8.27 (210.0)
10.61 (269.5)
22.93 (582.5) 

1AA6P1P5346-- (KV6B)©2006 Eiki International, Inc.
A-key to better communications
U.S.A.
EIKI International, Inc.
30251 Esperanza
Rancho Santa Margarita
CA 92688-2132
U.S.A.
Tel : 800-242-3454 (949)-457-0200 
Fax : 800-457-3454 (949)-457-7878
E-Mail : [email protected]
Canada
Deutschland & Österreich
EIKI Deutschland GmbH
Am Frauwald 12 
65510 Idstein
Deutschland
Tel : 06126-9371-0 
Fax : 06126-9371-14
E-Mail : [email protected]
Eastern Europe
EIKI CZECH spol. s.r.o.
Umelecká 15
170 00 Praha 7 
Czech Republic
Tel...

- 1 -
E
LCD PROJECTOR
LENS REPLACEMENT AND INSTALLATION PROCEDURES
CAUTION
When installing or replacing the Projection Lens, refer to this manual. For
installation of the lens, use the parts designated in the manual. Do not use the
installation manual and Light-Block Sheets in the lens package.
Check the following parts supplied to this projector.
NOTES ON LENS INSTALLATION
●Lens installation and replacement should be made by the qualified service
personnel.
●Be sure to install the lens following this...

- 2 -
E
NOTE : The installation procedure and needed parts
for lens installation depend on the type of the
Projection Lens. Check the Model No. of the
Projection Lens and be sure to install or replace the
lens following procedure below.
1  
Remove Lens Cover. Remove 2 Screws A. Push
part B and pull Upper Lens Cover up.  (See Fig. 1.)
2  
Remove 4 Screws C. Pull Lower Lens Cover
toward front and remove. (See Fig. 2.)
3  
Remove 2 Screws D and Cover Plate on the
back of Upper Lens Cover. (See Fig. 3.)
LENS...

- 3 -
E
LENS LOCK SCREW
DRIVER 
IN THE LENS LOCATE MOTOR
ON RIGHT SIDELENS ATTACHMENT
Part No. (910 275 6020)
CONNECTOR
Fig-4
LENS MOTOR LEAD Fig-5
LENS LOCK
LEVER
LENS
ATTACHMENT SOCKET
Lens attachments For each lens.
LNS-W01, LNS-W01Z, LNS-W02Z,
LNS-W03, LNS-T01, LNS-T01Z,
LNS-T02, LNS-T03, LNS-S02,
LNS-S02Z, LNS-S03, LNS-M01Z,
LNS-W04, LNS-W06 Lens Attachment 01
POA-LNA-01
(910 303 8743)
LNS-W02, LNS-M01Lens Attachment 02
POA-LNA-02
(910 304 6229)
Lens Model No.LENS ATTACHMENT
TYPE No. (PART No.)
4...

- 4 -
E
6  
This projector has 6 Light-Block Sheets. Use 2 Light-Block Sheets corres\
ponding with lens. (Refer to the list
below.)  Use 1 Light-block Sheet for MODEL LNS-W03
Set 2 Light-Block Sheets through the lens.  Make sure the shape of the Light-Block Sheets are correct and be sure to\
 set them as shown in the Fig. 8.
NOTE:
●Be sure to set each Light-Block Sheet as shown in Fig-8.
●  Make sure the mark (TOP and BACK) on Light-Block Sheets are correct an\
d set them properly.
Light-Block Sheets For...