Eiki Lc-Xt9 Multimedia Projector Owners Manual

							51
APPENDIX
COMPATIBLE COMPUTER SPECIFICATIONS
–––––––– (Interlace)
1024 x 768 (Interlace)
ON-SCREEN
DISPLAYRESOLUTIONH-Freq.(kHz)V-Freq. (Hz)
VGA 1640 x 48031.4759.88
VGA 2720 x 40031.4770.09
VGA 3640 x 40031.4770.09
VGA 4640 x 48037.8674.38
VGA 5640 x 48037.8672.81
VGA 6640 x 48037.5075.00
MAC LC13640 x 48034.9766.60
MAC 13640 x 48035.0066.67
MAC 16832 x 62449.7274.55
MAC 191024 x 76860.2475.08
MAC 211152 x 87068.6875.06
45.0060.00
SVGA 1800 x 60035.15656.25
SVGA 2800 x 60037.8860.32
SVGA 3800 x 60046.87575.00
SVGA 4800 x 60053.67485.06
SVGA 5800 x 60048.0872.19
SVGA 6800 x 60037.9061.03
SVGA 7800 x 60034.5055.38
SVGA 8800 x 60038.0060.51
SVGA 9800 x 60038.6060.31
SVGA 11800 x 60038.0060.51
ON-SCREEN DISPLAYRESOLUTIONH-Freq.(kHz)V-Freq. (Hz)
XGA 111024 x 768
XGA 131024 x 768
XGA 141024 x 768
61.0075.70
XGA151024 x 768
46.9058.20
XGA 81024 x 768
47.0058.30
XGA 91024 x 768
(Interlace)
58.0372.00
SXGA 11152 x 864
SXGA 21280 x 1024
63.4879.35
SXGA 31280 x 1024
36.0087.17
SXGA 41280 x 1024
64.2070.40
SXGA 51280 x 1024
62.5058.60
SXGA 61280 x 1024
63.9060.00
SXGA 71280 x 1024
63.3459.98
SXGA 81280 x 1024
63.7460.01
SXGA 111152 x 900
71.6967.19
SXGA 121152 x 900
81.1376.107
SXGA 131280 x 1024 (Interlace)
63.9860.02
SXGA 141280 x 1024(Interlace)
61.2065.20
71.4075.60
50.0086.00
50.0094.00
XGA 11024 x 768
XGA 21024 x 768
XGA 31024 x 768
XGA 41024 x 768
48.3660.00
68.67784.997
XGA 61024 x 768
60.02375.03
XGA 71024 x 768
56.47670.07
48.5060.02
44.0054.58
SXGA 91280 x 1024
SXGA 101280 x 960
79.97675.025
60.0060.00
SXGA 151280 x 1024
SXGA 161280 x 1024
SXGA 171152 x 900
SXGA 181280 x 1024(Interlace)
63.3760.01
76.9772.00
61.8566.00
46.4386.70
SXGA 191280 x 102463.7960.18
XGA 51024 x 76860.3174.92
VGA 7640 x 48043.26985.00
575i–––––––– (Interlace)15.62550.00
480i–––––––– (Interlace)15.73460.00
1080i/60–––––––– (Interlace)33.7560.00
1035i–––––––– 
(Interlace)33.7560.00
SVGA 10800 x 60032.7051.09
SXGA 201280 x 102491.14685.024
480p–––––––– 
(Progressive)31.4759.88
XGA 101024 x 76862.0477.07
1080i/5028.12550.00
SXGA+ 11400 x 105063.9760.19
SXGA+ 21400 x 105065.3560.12
WXGA 31376 x 76848.3660.00
WXGA 41360 x 76856.1672.00
XGA 1235.52286.96
575p–––––––– 
(Progressive)31.2550.00
SXGA+ 31400 x 105065.1259.90
WXGA 11366 x 76848.3660.00
WXGA 21360 x 76847.7060.00
MAC1280 x 96075.0075.08
MAC1280 x 102480.0075.08
Basically this projector can accept a signal from all computers with V, \
H-Frequency mentioned below and less
than 230 MHz of Dot Clock.
720p–––––––– 
(Progressive)
UXGA 31600 x 120087.5070.00
UXGA 41600 x 120093.7575.00
UXGA 11600 x 120075.0060.00
UXGA 21600 x 120081.2565.00
37.5050.00720p–––––––– 
(Progressive)
WXGA 81280 x 76868.633684.837
WXGA 91280 x 80056.1649.600
WXGA 61280 x 76847.77659.870
WXGA 71280 x 76860.28974.893 
						

							52
APPENDIX
OPTIONAL PARTS
The parts listed below are optionally supplied.  When ordering those par\
ts, give the name and Type No. to the sales dealer.
●DVI Board (HDCP Compatible) Type No. : AH-72003
● 5 BNC Board Type No. : AH-72015
● Video/Y,C & S-Video Board Type No. : AH-72023
● D-Sub 15 Board Type No. : AH-72031
● Network Board Type No. : AH-72142                                                                \
             
● Dual SDI Board Type No. : AH-72162
● Warp & Blending Board Type No. : AH-72181
● DVI Board Type No. : AH-72002
NOTE : Specifications are subject to change without notice.
ON-SCREEN
DISPLAYRESOLUTIONH-Freq.(kHz)V-Freq. (Hz)
D-VGA640 x 48031.4759.94
D-480p720 x 480
(Progressive)31.4759.88
D-575p720 x 575
(Progressive)31.2550.00
D-SVGA800 x 60037.87960.32
D-XGA1024 x 76843.36360.00
ON-SCREEN
DISPLAYRESOLUTIONH-Freq.(kHz)V-Freq. (Hz)
D-WXGA 11366 x 76848.3660.00
D-WXGA 41360 x 76856.1672.00D-1035i1920 x 1035(Interlace)33.7560.00
D-1080i/601920 x 1080 (Interlace)33.7560.00
D-1080i/501920 x 1080(Interlace)28.12550.00
D-WXGA 21360 x 76847.7060.00
D-WXGA 31376 x 76848.3660.00D-720p1280 x 720
(Progressive)37.5050.00
D-SXGA 11280 x 102463.98060.020
When a input signal is digital from DVI terminal, refer to chart below.
D-SXGA 21280 x 102460.27658.069
Depending on the condition of signals and the type and length of cables,\
 these signals may not be properly viewed.
1400 x 105063.97060.19D-SXGA+ 1
D-UXGA 11600 x 120075.0060.00
D-720p1280 x 720
(Progressive)45.0060.00
D-WXGA 51366 x 76846.50050.000
D-WXGA 61280 x 76847.77659.870
D-WXGA 81280 x 76868.63384.837
D-WXGA 91280 x 80049.60060.050
D-WXGA 71280 x 76860.28974.893 
						

							53
APPENDIX
Owner’s Manual (CD-ROM)
Quick setup manual
AC Power Cord
Wireless/Wired Remote Control Transmitter and Batteries
VGA Cable
6 Types Light-Block Sheet (For option lens)
2 Types Lens Attachment (For option lens)
Real Color Manager ProAccessories
TECHNICAL SPECIFICATIONS
1.8 TFT Active Matrix type, 3 panels
Multi-media Projector
80.3 lbs (36.5 kg)
22.9 x 10 x 30.9 (581 mm x 252 mm x 783 mm) 
1024 x 768 dots
2,359,296 (1024 x 768 x 3 panels)
PAL, SECAM, NTSC, NTSC4.43, PAL-M and PAL-N (With option video board)
Up, Down, Left and Right
800 TV lines
41 ˚F ~ 95 ˚F (5 ˚C ~ 35 ˚C)
14 ˚F ~ 140 ˚F (-10 ˚C ~ 60 ˚C)
Projector Type
Net Weight
Dimensions (W x H x D)
Panel Resolution
Number of Pixels
Color System
Scanning Frequency
Horizontal Resolution
Operating Temperature
Storage Temperature
LCD Panel System
250 watt type x 4Projection Lamp
0˚ to 5.7˚Feet Adjustment
Power Source : AA or LR6 Type x 2
Operating Range : 16.4’ (5m) / ±30˚
Dimensions : 1.97” x 1.06” x 6.61” (50mm x 27mm x 168mm)
Net Weight : 4.6 oz (129 g) (including batteries)Remote Control Transmitter
480i, 480p, 575i, 575p, 720p, 1035i, 1080i-50 and 1080i-60High Definition TV Signal
AC 120 V           (12 A  Max. Ampere), 50 / 60 Hz  (The U.S.A and Canada)
AC 200 ~ 240 V (7.5 A  Max. Ampere), 50 / 60 Hz  (Continental Europe)
Voltage and 
Power Consumption
H-sync. 15 ~ 120 KHz, V-sync. 50 ~ 120 Hz
Motorized Lens Shift
DVI-I Terminal (Digital/Analog), RCA Type (Audio R and L)
and DIN 8-pin (Control port)Input 1 Jacks
BNC Type x 5 (R/Pr, G/Y, B/Pb, H/HV and V), RCA Type (Audio R and L)\
and DIN 8-pin (Control port)Input 2 Jacks
HDB 15-pin Terminal (Analog), RCA Type (Audio R and L)
and DIN 8-pin (Control port)Input 3 Jacks
Serial port in (DB 9), Serial port out (DB 9), USB port,
Audio out (RCA Type R and L) and Wired Remote Jack Other Jacks
●Specifications are subject to change without notice.
● LCD panels are manufactured to the highest possible standards. At least \
99.99% of the pixels are effective,
however a tiny fraction of the pixels (0.01% or less) may be ineffecti\
ve by the characteristics of the LCD
panels.
● Each projector has its own characteristics.
When projecting with several projectors on the same screen or side by si\
de, you may recognize differentwhite balance and color uniformity on each projector. 
						

							54
APPENDIX
Vcc
- Data
+ Data
Ground
1
2
3
4
USB PORT TERMINAL
Pin Configuration
Connect USB port output terminal of computer
or peripheral equipment to this terminal with
USB port  Cable (not supplied).
2
34 1
CONFIGURATIONS OF TERMINALS
HDB 15-PIN TERMINAL (ANALOG)
Connect display output terminal of computer to this terminal with VGA Ca\
ble (supplied).
512341096781514131112
Red Input
Ground (Horiz.sync.)
Green Input
Sense 2
Blue Input
Ground (Red)
Ground (Green)
Ground (Blue)
1
5
2
4
3
6
7
8
+5V Power
Horiz. sync.
Ground (Vert.sync.)
DDC Data
Sense 0
Vert. sync.
DDC Clock
9
13
10
12
11
14
15
Pin Configuration
DVI-I TERMINAL (DIGITAL/ANALOG) 
This terminal accepts only Digital (TMDS) or Analog (RGB) output sig\
nal. Connect  display output terminal of computer to
this terminal with DVI cable (not supplied).  
1917
21018
31119
41220
51321
61422
71523
81624
C1
C2
C3 C5 C4
T.M.D.S. Data2–
No Connect
T.M.D.S. Data2+
No Connect
T.M.D.S. Data2 Shield
DDC Clock
DDC Data
Analog Vert. sync
1
5
2
4
3
6
7
8
Pin Configuration
T.M.D.S. Data1–
No Connect
T.M.D.S. Data1+
No Connect
T.M.D.S. Data1 Shield
+5V Power
Ground (for +5V)
Hot Plug Detect
9
13
10
12
11
14
15
16
T.M.D.S. Data0–
No Connect
T.M.D.S. Data0+
No Connect
T.M.D.S. Data0 Shield
T.M.D.S. Clock Shield
T.M.D.S. Clock+
T.M.D.S. Clock–
17
21
18
20
19
22
23
24
Analog Red Input
Analog Ground (R/G/B)
Analog Green Input
Analog Horiz. sync
Analog Blue Input
C1
C5
C2
C4
C3
-----
RxD
TxD
-----
Ground
-----
-----
-----
1
2
3
4
5
6
7
8
9-----
1
2
3
4
5
6
7
8
9
Connect serial port output terminal of computer to this terminal with Se\
rial Cable (not supplied).
Pin Configuration
SERIAL PORT IN/OUT TERMINAL 
						

							55
APPENDIX
DIMENSIONS
22.87 (581.0)
Unit : inch (mm)Screw Holes for Ceiling Mount
Screws: 9-M8
Depth: 0.315 (8.0)
9.90 (251.5)10.15 (258.0)
5.18 (131.5)
9.90 (251.5)
5.7 °
2.36 (60.0)
30.83 (783.0)
17.56 (446.0)
22.87 (581.0)
9.25 (235.0)
8.62 (219.0) 17.56 (446.0)
7.01 (178.0) 7.01 (178.0)
4.23 (107.5)
3.26 (82.8)
9.72 (247.0)
14.74 (374.5)
6.81 (173.0) 1.38 (35.0)
1.57 (40.0)
8.27 (210.0) 8.27 (210.0)
10.61 (269.5)
22.93 (582.5) 
						

							1AA6P1P5346-- (KV6B)©2006 Eiki International, Inc.
A-key to better communications
U.S.A.
EIKI International, Inc.
30251 Esperanza
Rancho Santa Margarita
CA 92688-2132
U.S.A.
Tel : 800-242-3454 (949)-457-0200 
Fax : 800-457-3454 (949)-457-7878
E-Mail : [email protected]
Canada
Deutschland & Österreich
EIKI Deutschland GmbH
Am Frauwald 12 
65510 Idstein
Deutschland
Tel : 06126-9371-0 
Fax : 06126-9371-14
E-Mail : [email protected]
Eastern Europe
EIKI CZECH spol. s.r.o.
Umelecká 15
170 00 Praha 7 
Czech Republic
Tel : +42 02 20570024
+42 02 20571413 
Fax : +42 02 20571411
E-Mail : [email protected]
J apan & Worldwide
EIKI Industrial Company Limited.
4-12 Banzai-Cho, Kita-Ku, Osaka, 
530-0028 Japan
Tel : +81-6-6311-9479 
Fax : +81-6-6311-8486
E-Mail : [email protected]
W orldWide Website  http://www.eiki.com
ˆ
EIKI CANADA - Eiki International, Inc.
P.O. Box 156, 310 First St. - Unit 2,
Midland, ON, L4R 4K8, Canada 
Tel : 800-563-3454 (705)-527-4084
Fax : 800-567-4069 (705)-527-4087
E-Mail : [email protected] 
						

							- 1 -
E
LCD PROJECTOR
LENS REPLACEMENT AND INSTALLATION PROCEDURES
CAUTION
When installing or replacing the Projection Lens, refer to this manual. For
installation of the lens, use the parts designated in the manual. Do not use the
installation manual and Light-Block Sheets in the lens package.
Check the following parts supplied to this projector.
NOTES ON LENS INSTALLATION
●Lens installation and replacement should be made by the qualified service
personnel.
●Be sure to install the lens following this procedure precisely.
●Do not touch or remove any parts except the lens and related parts. It may
result in malfunctions, electrical shock, fire hazard  or other accidents.
●Before installing or replacing the lens, check that the Model No. of the
Projection Lens matches to the projector.
●When moving or setting up the projector, be sure to replace the Lens Cover
to protect the surface. And be careful not to hold or subject the lens to
strong forces. It may damage the lens, cabinet, or mechanical parts.
●For details of the lens and installation, contact the sales dealer where\
 you
purchased the projector.
●  LIGHT-BLOCK SHEETS    6 pcs.
●  LENS ATTACHMENT (01) 1 pce.
●  LENS ATTACHMENT (02) 1 pce.
This projector applies the Projection Lenses listed below. Use the suitable lens for
where the projector is used.
AVAILABLE LENS
Model NO.
LNS-W01
LNS-W01Z
LNS-T01
LNS-T01Z
LNS-T02
LNS-W02
LNS-W02Z
LNS-M01  
LNS-M01Z
LNS-S02
LNS-S02Z
Type
Fixed Short Throw Lens
Fixed Long Throw Lens
Long Throw Zoom Lens
Short Throw Zoom Lens  I
Semi-Long Throw 
Zoom Lens
Standard Zoom Lens  II
Zoom
Motor Driven
FixedManual
Focus
Fixed
Motor Driven
Motor Driven
Motor Driven
Manual
Motor Driven
Motor Driven
Motor Driven
Motor Driven
LNS-W03
LNS-S03
Short Throw Zoom Lens  II
Standard Zoom Lens III
FixedManual
Motor DrivenMotor Driven
LNS-W04Wide Zoom LensMotor DrivenMotor Driven
LNS-W06Wide Zoom LensMotor DrivenMotor Driven
LNS-T03Long Throw Zoom LensManualManual 
						

							- 2 -
E
NOTE : The installation procedure and needed parts
for lens installation depend on the type of the
Projection Lens. Check the Model No. of the
Projection Lens and be sure to install or replace the
lens following procedure below.
1  
Remove Lens Cover. Remove 2 Screws A. Push
part B and pull Upper Lens Cover up.  (See Fig. 1.)
2  
Remove 4 Screws C. Pull Lower Lens Cover
toward front and remove. (See Fig. 2.)
3  
Remove 2 Screws D and Cover Plate on the
back of Upper Lens Cover. (See Fig. 3.)
LENS REPLACEMENT AND INSTALLATION PROCEDURE
Fig-1
UPPER LENS
COVER 
A
Fig-2
LOWER LENS
COVER 
C
COVER PLATE
UPPER LENS
COVER 
D
Fig-3
C
B 
						

							- 3 -
E
LENS LOCK SCREW
DRIVER 
IN THE LENS LOCATE MOTOR
ON RIGHT SIDELENS ATTACHMENT
Part No. (910 275 6020)
CONNECTOR
Fig-4
LENS MOTOR LEAD Fig-5
LENS LOCK
LEVER
LENS
ATTACHMENT SOCKET
Lens attachments For each lens.
LNS-W01, LNS-W01Z, LNS-W02Z,
LNS-W03, LNS-T01, LNS-T01Z,
LNS-T02, LNS-T03, LNS-S02,
LNS-S02Z, LNS-S03, LNS-M01Z,
LNS-W04, LNS-W06 Lens Attachment 01
POA-LNA-01
(910 303 8743)
LNS-W02, LNS-M01Lens Attachment 02
POA-LNA-02
(910 304 6229)
Lens Model No.LENS ATTACHMENT
TYPE No. (PART No.)
4  
Remove Lens Cap on the rear (mounting side) of Projection Lens and mou\
nt Lens on the lens
Attachment with 4 Screws. (Use screws attached on lens.)
Connect the Lens Motor Lead connector to the socket on the right-top of \
the lens attachment.
(Motor Driven Lens only.) See Fig. 5.
Fig-6Fig-7
LENS LOCK RELEASE LENS LOCK 
5  
Grasp the Lens Lock Lever and turn it fully upward. (See Fig. 6.)
Install the Lens into the projector. Grasp the Lens Lock Lever and turn \
the Lever fully downward until
lever is Locked (clicked position) properly. (See Fig. 7.) When installing the Motor Driven Lens, be sure to mount Lens Motor on ri\
ght side. (See Fig. 4.)
After installing the lens, make sure the Lens is not loose and properly \
installed.
NOTE: Please go while supporting the lens when you detach the lens for s\
afety.
Grasp the Lens
Lock Lever and
pulling upward.
Grasp (unlock)
Lens Lock Lever
and fully pulled
downward until it is
locked (clicked).
Lens Lock
Lever  
						

							- 4 -
E
6  
This projector has 6 Light-Block Sheets. Use 2 Light-Block Sheets corres\
ponding with lens. (Refer to the list
below.)  Use 1 Light-block Sheet for MODEL LNS-W03
Set 2 Light-Block Sheets through the lens.  Make sure the shape of the Light-Block Sheets are correct and be sure to\
 set them as shown in the Fig. 8.
NOTE:
●Be sure to set each Light-Block Sheet as shown in Fig-8.
●  Make sure the mark (TOP and BACK) on Light-Block Sheets are correct an\
d set them properly.
Light-Block Sheets For each lens.
Fig-8
LIGHT BLOCK SHEETS
Make sure the sheet figures are
correct and put in proper position.LIGHT BLOCK SHEET
Make sure the sheet figure is
correct and put in proper position.
MODEL LNS-W03
Lens Model No. 
LNS-S02, LNS-S02Z
LNS-M01, LNS-T02, LNS-W02
LNS-M01Z, LNS-W02Z
LNS-W01, LNS-T01, LNS-W01Z
LNS-T01Z, LNS-S03, LNS-W04
LNS-W06
T ype No. (Part No.)
LNS-W03
TYPE   FA1  (910 322 7550)
TYPE   FA2  (910 322 7895)
TYPE   FB1  (910 322 7710)
TYPE   FB2  (910 322 7352)
TYPE   FC1  (910 322 8137)
TYPE   FC2  (910 322 4320)
TYPE   FB1  (910 322 7710)