Eiki Lc-Xt9 Multimedia Projector Owners Manual

11
MOVING PROJECTOR
For safety, be sure to hold Carrying Handles
on both sides by 2 or more people when
moving a projector. Moving it unproperly may
result in damage of cabinet or persons
injury.
Replace lens cap and retract feet to prevent
damage to lens and cabinet.
1
2
3
Pull up lock buttons on each side of carrying handles
and  release locks.
CARRYING
HANDLE
LOCK BUTTONSPull carrying handles out fully until its locked (with a
click). Move a projector by holding two handles by 2 or
more people.
To...

12
CONNECTING PROJECTOR
TERMINALS OF PROJECTOR
This projector applies various input/output terminals and 4 terminal slo\
ts for expansion to tune to diversity of signals from
computers and video equipment. 4-built-in Terminal Slots enable you to a\
rrange desired combinations of input sources just
by changing Terminal Boards.  For Terminal Boards, contact sales dealer \
where you purchased a projector.
Pull out terminal by holding handle.
Remove 2 Screws on terminal.1
2
REPLACEMENT OF TERMINAL
Tighten...

13
CONNECTING PROJECTOR
ANALOG RGB
R/Pr G/Y B/Pb H/HV V
CONTROL PORTDV I
INPUT 1
R/C JACKUSB
RESET
(MONO) (MONO)
(MONO)
(MONO)
CONTROL PORT
A
UDIO
CONTROL PORT
INPUT 2
INPUT 3
INPUT 4
A UDIO
A UDIO
SERIAL PORT IN
SERIAL PORT OUT
AUDIO OUTRL
RL
R
R
L
L
The port is not functioning
in this model.
Connect audio output
from computer or video
equipment to these jacks.
(Refer to P15, 16.)
CONTROL PORT CONNECTORS
AUDIO INPUT JACKS5 BNC INPUT JACKS
Connect component video output (Cr, Y,
Cb or Pr, Y, Pb) from...

14
CONNECTING PROJECTOR
Connect an external audio
amplifier to these jacks.  
(Refer to P15, 16.)
AUDIO OUTPUT JACKS
This projector uses a micro processor to control unit.
Occasionally, micro processor may malfunction and
need to be reset.  This can be done by pressing
RESET button with a pen, which will shut down and
restart unit. Do not use RESET function excessively.
RESET BUTTON
When using Wired / Wireless Remote
Control Unit as Wired Remote
Control, Connect Wired Remote
Control Unit to this jack...

15
CONNECTING PROJECTOR
ANALOG RGB
R/Pr G/Y B/Pb H/HV V
CONTROL PORTDV I
INPUT 1
R/C JACKUSB
RESET
(MONO) (MONO)
(MONO) (MONO)
CONTROL PORT
A
UDIO
CONTROL PORT
INPUT 2
INPUT 3
INPUT 4
AU DIO
A UDIO
SERIAL PORT IN
SERIAL PORT OUT
AUDIO OUTRL
RL
R
R
L
L
CONNECTING TO COMPUTER
IBM-compatible computers or Macintosh computers (VGA / SVGA / XGA / SXG\
A/WXGA/UXGA)
VGA Cable 
Monitor Output 
Desktop type Laptop type
Audio Cable
(stereo) ✽
Audio Output
Audio Input AUDIO OUT
Cables used for connection(✽= Cables...

16
CONNECTING PROJECTOR
CONNECTING TO VIDEO EQUIPMENT
ANALOG RGB
R/Pr G/Y B/Pb H/HV V
CONTROL PORTDV I
INPUT 1
R/C JACKUSB
RESET
(MONO) (MONO)
(MONO) (MONO)
CONTROL PORT
A
UDIO
CONTROL PORT
INPUT 2
INPUT 3
INPUT 4
A UDIO
A UDIO
SERIAL PORT IN
SERIAL PORT OUT
AUDIO OUTRL
RL
R
R
L
L
Video Source (example)
Video Cassette Recorder Video Disc Player
RGB Scart
21-pin Output
Audio Amplifier Audio Speaker (stereo)
Audio Cable 
(Stereo) ✽
Audio Input
Cables used for connection
• Video Cable (BNC x 3) ✽• DVI Cable...

17
BEFORE OPERATION
IMAGE BUTTON
Used to select image
level.  (P31, 36)
MENU
AUTO  PC ADJ. IMAGE
SELECT
ZOOM FOCUS
LENS SHIFTON-OFFINPUT 1/2
INPUT 3/4


SIDE CONTROLS AND INDICATORS
Used to adjust zoom.
(P24)
INPUT 3/4 BUTTON
POWER ON–OFF BUTTONFOCUS BUTTONS
Used to select input source
either INPUT 3 or INPUT 4.
(P26, 34)
Used to adjust focus.  (P24)
Used to select an item or
adjust value in MENU.  It is
also used to pan image in
DIGITAL ZOOM mode.
(P33)
Used to execute item
selected.  It is also used...

18
BEFORE OPERATION
READYLAMP
LAMP
REPLACE W
ARNING
TEMP.
READY INDICATORLAMP INDICATORLAMP REPLACE INDICATOR
This indicator lights green
when a projector is ready to
be turned on.  And it
flashes green in Power
Management mode. 
(P40, 42, 50)This indicator is dim when a
projector is turned on.  And
bright when a projector is in
stand-by mode. (P50)
INDICATORS
WARNING TEMP. INDICATOR
This indicator flashes red
when internal projector
temperature is too high.
(P42, 50)
W ARNING
TEMP.
READY
LAMP
REPLACE...

19
BEFORE OPERATION
OPERATION OF REMOTE CONTROL
LIGHT BUTTON
Lights the buttons on the remote
control for about 10 seconds.
Used to select input
source.  (P26, 34)
POWER ON-OFF BUTTON
Used to turn projector on or
off.  (P23)
MENU BUTTON
Used to select MENU
operation.  (P21, 22)
INPUT 1, 2, 3, 4 BUTTONS
AUTO PC ADJ. BUTTON
Used to operate AUTO PC
Adjustment function.  (P28)
FREEZE BUTTON
Used to freeze picture.
(P25)
SELECT BUTTONPOINT (UP / DOWN / LEFT / RIGHT)
BUTTONS
Used to select an item or adjust...

20
BEFORE OPERATION
16.4’
(5 m)
60°
16.4’
(5 m)
60°
To insure safe operation, please observe following precautions : ●Use (2) AA or LR6 type alkaline batteries.
● Replace two batteries at same time.
● Do not use a new battery with an used battery.
● Avoid contact with water or liquid.
● Do not expose Remote Control Unit to moisture, or heat.
● Do not drop Remote Control Unit.
● If a battery has leaked on Remote Control Unit, carefully wipe case clea\
n and install new batteries.
● Danger of explosion if...