Eiki Lc-Xl200l Multimedia Projector Owners Manual

61

Shutter function is available to block out light to the screen, so that \
the screen can be used for the other presenters.
Prohibit the shutter operation from the remote control and the 
projector's side control.Remote	control
   . .  
Selecting On prohibits the shutter 
operation from the remote control.  
Projector. . . .       Selecting On prohibits the shutter   
operation from the side control.
It is possible to prohibit the shutter operation from both of the 
remote control and the side...

62

This function returns all setting values except for User	logo, 
PIN	code	lock
,  Logo	PIN	code	lock, Lamp	counter, and 	Filter	
counter	
to the factory default settings.
Various test pattern are available for use when setting up the 
projector.
Filter replacement icon appears on the screen at a set time.
Note:
	 •	 Do	not	reset	the	counter	when	the	filter	or	the	filter	cartridge	is	not	replaced.
	 •	 Timer	setting	notifies	that	the	filter	needs	replacement.	To	replace	the 	
filter,	use	the	filter...

6

Filter prevents dust from accumulating on the optical elements inside th\
e projector. Should the filter becomes clogged with 
dust particles, it will reduce cooling fans’ effectiveness and may result in internal heat buildup and adversely affect the life 
of the projector. This projector has an electrically operated filter which helps you to re\
place the filter easily. The projector 
monitors the condition of the filter at all time and replaces a filter w\
ith a new one automatically when it...

64

Turn off the projector, and unplug the AC power cord from the 
AC outlet.
First, clean up the dust on the projector and around the air 
vents.
1
2
Press ▼ downwards on the filter cover to release the latch 
and open the filter cover.
Put the new one back into the position and close the filter 
cover. Make sure that the filter cartridge is properly and fully 
inserted.
5
CAUTION
Make sure the filter cartridge is inserted in the projector. If 
the filter cartridge is not inserted, the projector...

65

Be sure to reset the Scroll counter after replacing the filter cartridge\
. 
Press the MENU button to display the On-Screen Menu. Use 
the Point ▲▼ buttons to select Setting and then press the 
Point ► or the SELECT button.
Use the Point ▲▼ buttons to select Filter	counter and then 
press the SELECT button. Use the Point ▲▼ buttons to 
select Scroll	counter	Reset and then press the SELECT 
button.  Scroll	counter	Reset?	appears. Select  yes to 
continue.
1
2
Scroll	counter
Another confirmation...

66

Turn off the projector and unplug the AC power cord. Let the 
projector cool for at least 45 minutes.
Loosen the screw and open the lamp cover. Loosen 3 screws 
of the lamp and pull out the lamp by using the built in handle.
1
Replace the lamp with a new one. Make sure that the lamp is 
properly and fully inserted. 
4
2
Connect the AC power cord to the projector and turn on the 
projector.
Follow these steps to replace the lamp.
5
Note:
	 Be	sure	to	insert	the	lamp	in	the	correct	direction....

67

ORDER	REPLACEMENT	LAMP
Replacement lamp can be ordered through your dealer. When ordering, give the following information to the 
dealer.
 ●   Model	No .	of	your	projector	 :LC-XL100,	LC-XL200,	LC-XL100L,	LC-XL200L
 ●  Replacement	Lamp	Type	No .	 :POA-LMP17	(For	LC-XL100,	LC-XL100L)
              (Service Parts No. 610 347 5158)
																																																															POA-LMP16	(For	LC-XL200,	LC-XL200L)
               (Service Parts No. 610 346 9607)
Maintenance	and...

6

Unplug the AC power cord before cleaning.
Gently wipe the projection lens with a cleaning cloth that 
contains a small amount of non-abrasive camera lens cleaner, 
or use a lens cleaning paper or commercially available air 
blower to clean the lens. 
Avoid using an excessive amount of cleaner. Abrasive 
cleaners, solvents, or other harsh chemicals might scratch the 
surface of the lens.
Unplug the AC power cord before cleaning.
Gently wipe the projector body with a soft dry cleaning cloth. 
When...

69

Maintenance	and	Care
The WARNING indicators show the state of the function which protects the proj\
ector. Check the state of the WARNING 
indicators and the POWER indicator to take proper maintenance. 
The	projector	is	shut	down	and	the	WARNING	
TEMP .	indicator	is	blinking	red .
When the temperature inside the projector reaches a
certain level, the projector will be automatically shut down to 
protect the inside of the projector. The POWER indicator is blinking 
while the projector is being cooled...

70

Before calling your dealer or service center for assistance, check the i\
tems below once again.
1. Make sure you have properly connected the projector to peripheral equipment as described on pages 19-21.
2.  Check the cable connection. Make sure that all computers, video equipment, and power cords are properly connected.
3.  Make sure that all power is switched on.
4.  If the projector still does not produce an image, restart your computer.
5.  If an image still does not appear, disconnect the...