Eiki Lc-Xl200l Multimedia Projector Owners Manual

11

⑦ R/C	jACK
  When using the wired remote control, connect the wired remote 
control to this jack with a remote control cable (supplied) (p.15).
⑮ USB	CONNECTOR	(Series	B)
  Use this connector when controlling a computer 
with the remote control of the projector. Connect the USB terminal of your computer to this connector with the supplied USB cable (p.19).
⑭ AUDIO	2	jACK
  Connect the audio output (stereo) signal from a 
computer or video equipment (p.21).
⑪ VIDEO	INPUT	jACK
  Connect the component...

12

① ON/STAND-By	button
  Turn the projector on or off (pp.23-24).
② MENU	button
  Open or close the On-Screen Menu (p.25).
⑤ Point	▲▼◄► 	(	VOLUME	 –	/	+	)	buttons
  – Select an item or adjust the value in the On-
Screen Menu (p.25).
  – Pan the image in Digital zoom + mode (p.43).
  – Adjust the volume level (with Point ◄► buttons) 
(p.28).
⑩  WARNING	TEMP  .	indicator
  Blink red when the internal temperature of the 
projector exceeds the operating range (pp.69, 
76-78).
④ 
SHUTTER	button
    
Close...

1

① STAND-By	button
  Turn the projector off (p.24).
④	 ON	button
  Turn the projector on (p.23).
⑥ INPUT	button
  Select a signal (pp.33-35).
⑧ SCREEN	button
 Select the screen size (p.29).


⑭

⑭ L- CLICK 	button
  Act as the left mouse button for wireless mouse 
operation (p.32).
③ SIGNAL	EMISSION 	indicator
  Light red while a signal is being sent from the 
remote control to the projector.
⑨ POINT	▲▼◄►(	VOLUME	 –	/	+,	MUTE)	buttons
  – Select an item or adjust the value in the On-
Screen...

14

⑯
⑮
⑲
⑰
⑱
⑱ ZOOM	▲▼ buttons
  Zoom in and out the images (p.29).
⑮ D .ZOOM	button
  Select the Digital zoom +/- mode and resize the 
image (p.43).
⑲ FOCUS	buttons
  Adjust the focus (p.29).
㉑		FILTER 	button
    Scroll the filter (p.30).
㉓   FREEZE	button
  Freeze the picture on the screen (p.30).
⑰ KEySTONE	button
  Correct keystone distortion (pp.31, 44, 50).
⑳	 RESET/ON/ALL-OFF	switch
  When using the remote control, set this switch to 
“ON”.  Set it to “ALL OFF” for power saving when 
it is not...

15

12
Open the battery 
compartment lid.
Install new batteries into 
the compartment.
Replace the 
compartment lid.
Press the lid downward and slide it.Two	
AAA	size	batteriesFor correct polarity (+ and –), be sure battery terminals are in contact with pins in the compartment.
To ensure safe operation, please observe the following precautions :
 ● Use two (2) AAA or LR03 type alkaline batteries.
  ● Always replace batteries in sets.
  ● Do not use a new battery with a used battery.
  ● Avoid...

16

The eight different remote control codes (Code 1–Code 8) are assigned to this pr\
ojector. Switching the remote control 
codes prevents interference from other remote controls when several proj\
ectors or video equipment next to each other are 
operated at the same time. Change the remote control code for the projec\
tor first before changing that for the remote control. 
See “Remote control” in the Setting Menu on page 56.
Press and hold the MENU and a number button (1–8) for 
more than five...

17

Installation
For projector positioning, see the figures below. The projector should be set perpendicularly to the plane of the screen (\
for 
LC-XL100 and LC-XL200).
Note:
	 •	The	brightness	in	the	room	has	a	great	influence	on	picture	quality.	It	is	recommended	to	limit	ambient	
				lighting	in	order	to	obtain	the	best	image.
	 •	All	measurements	are	approximate	and	may	vary	from	the	actual	sizes.
100”
33.1’(10.11 m)
22.0’ (6.73 m)
16.5’ (5.03 m)
10.9’ (3.34 m)
150”
200”
300”
177”
118”89”59”40”...

1

When replacing the lens or using an optional lens, install the lens by f\
ollowing the instructions below. Ask the 
sales dealer for detailed information of the optional lens specification\
s. 
Installation
NOTES	ON	LENS	INSTALLATION
  ● Do not touch or remove any parts except the lens and related parts. It may result in    
  malfunctions, electrical shock, fire hazard or other accidents.
  ● Before installing or replacing the lens, check that the Model No. of the Projection Lens  
  matches to...

19

Monitor Output
BNCcable
Monitor Output
G   B   R   H/V   V
DVI-Digital cableVGA cableVGA cable
USB cable
USB port
Unplug	the	power	cords	of	both	the	
projector	and	external	equipment	from	the	
AC	outlet	before	connecting	cables.
Cables	used	for	connection  ( = Cables not supplied with this projector.)
• VGA Cable (One cable is supplied.) 
• DVI-Digital cable  
• BNC cable  
• Serial Cross cable 
• USB cable
Monitor Output
DIGITAL INANALOG INANALOG OUTUSB
Serial Crosscable
Serial out
CONTROL...

20

RGB Scart21-pin Output
S-video cable
S-video OutputComposite Video
Y - Pb/Cb - Pr/Cr
BNC cable
Unplug	the	power	cords	of	
both	the	projector	and	external	
equipment	from	the	AC	outlet	
before	connecting	cables.
Cables	used	for	connection ( = Cables not supplied with this projector.)
• Video cable (RCA x 1 or RCA x 3) • BNC cable (BNC x 1 or BNC x 3) • S-video cable • Scart-VGA cable    • DVI-Digital cable 
Component Video OutputComposite Video
Component Video  Output(Y, Pb/Cb, Cr/Pr)
Digital...