Eiki Lc-Xip2000 Multimedia Projector Owners Manual

							Basic Operation
Turnin
g on the Projector - Procedure 
6. 
The power indicator will flash green. 
7. Press the Input button on the control panel or on the 
remote control to select the appropriate source. 
8. Rotate the zoom ring to adjust the screen size. 
9. Rotate the focus ring to adjust the focus. 
6POWER LAMP
9
8
6
KEYSTONE 
INPUT 
BLANK 
50 
  
						

							Basic Operation
Turnin
g off the Projector - Procedure 
1. 
Press the power button on the projector or remote control. The
power
 off confirmation message appears . 
2. Press the power button again and the projector will enter cool-down 
mode. The lamp shuts off, the lamp indicator flashes red, and the
fans
 continue to run for approximately two minutes. During the cool
down
 sequence the projector will not respond to any control panel 
or remote control buttons. 
Do not set the power switch to off or unplug the 
projector during the cool-down sequence. Not allowing 
the lamp to cool properly will greatly reduce the life 
of the lamp. 
C A U T I O N
3. After the cool-down sequence is completed the fans will shut off 
and the lamp indicator will stop flashing. The projector is now in 
standby mode and can be turned back on with the remote control 
or control panel. If the projector will not be used for an extended 
period, set the power switch to off and disconnect the power cord. 
51 
						

							Basic Operation
Ad
just the Screen Image  
1. Adjusting the image size 
Rotate the Zoom Ring to adjust the image.  
2. Adjusting the image height 
Extend or retract the front adjustable foot to adjust the height of 
the
 image. 
3. Correcting Keystone Distortion 
◆ Press the Keystone button on the control panel. 
◆ Keystone correction message will be appeared. 
◆  Press ”Left/Right” button to correct Keystone distortion. 
POWER LAMP 
KEYSTONE 
INPUT 
BLANK 
52 
Press ”Left button” to       
correct ke
ystone distortion. Press ”Right button” to       
correct keystone distortion.  
						

							Functions of Menu (OSD)
Keypad Operatin
g:
6.Menu-Up/Down 
Menu-Left/Right 1.Power 
5.Menu 
 
3.Auto A 7.Quick Key 
KEYSTONE 4.Input INPUT 2.Blank 
BLANK 
Turn on and turn off the projector 1.
2. Blank : Blanks the projected image. If the projector is left in Blank 
m o d e  f o r  m o r e  t h a n  1 5  m i n u t e s , t h e  p r o j e c t o r  w i l l 
automatically
 shut off the lamp and enter cool-down mode. 
 
3. Auto : Automatically adjusts the settings to match the current input. 
 
4. Input : Selects VIDEO or PC input source. 
 
5. Menu : Enter or exit the main menu (Show and hide the OSD) 
6. : Up / Down arrow buttons, used to navigate through the OSD Menus.  
: Right / Left arrow buttons, used to select and adjust OSD Menu 
functions. 
 
7. Quick Key : It can be selected the “Keystone/Brightness/ 
Contrast/Volume” by pressing “bottom” of MENU 
button and adjusted by pressing “Left/Right” bottom 
of MENU button on the control panel or remote 
control.
 
There is a “Quick Key“ on the remote control and projector keypad as 
well. 
53
POWER 
 
LAMP  
						

							 
1. PICTURE 
Brightness  000/100  Adjusts the overall image brightness 
Contrast  000/100  Adjusts the difference between 
light and dark  areas of the image 
Sharpness  000/002  Adjusts the image sharpness 
Display mode  Select 
Video 
Presentation 
Natural  
Green board 
 
User Keep the soft tender color 
For computer presentation use 
Nature color 
When using on green board 
 
Adjustments of each RGB color 
User Red 
User Green 
User Blue 000/100 
000/100 
000/100 
 
Functions of Menu (OSD)
Computer Mode-Picture Menu
54  
						

							2. AUDIO
Volume 000/040 Adjusts the volume 
Mute Off/on Mutes the volume on/off 
Functions of Menu (OSD)
Computer Mode-Audio Menu
55 
						

							3.SETTING
H position 
000/100 
Move the image position horizontally 
V position 
000/100 
Move the image position vertically 
Phase 
000/100 Set the synchronization polarity 
Frequency 
000/100 Set the horizontal scanning frequency 
Auto keystone 
off/on 
Automatically Corrects keystone 
distortion in image i.e. press once 
to do once 
Keystone V 
-80/+80 
Corrects vertical keystone distortion 
in image 
Auto sync  execute Sets all of the above 
settings automatically 
Auto search 
off/on 
Search signal source automatically. 
Functions of Menu (OSD)
Computer Mode-SETTING Menu
56  
						

							 
 
Functions of Menu (OSD)
Computer Mode-ADVANCED Menu
57 
						

							Functions of Menu (OSD)
Computer Mode-ADVANCED Menu
Blank on 
If the projector is left in Blank mode for more than 15 minutes, the
projector will automatically shut off the lamp and enter cool-down
mode. 
Reset all 
1. After you select [reset all] on the OSD menu, the following confirmation
message will appear on the screen. 
2. Press reset button on the remote control or the button on the control 
panel to reset the OSD Menu values. Press the ESC button or ignore the 
message to exit the Reset All function without changing any settings. 
58 4.ADVANCED 
Zoom/pan  execute  Execute digital zoom and pan function 
Still  on/off  Freezes the current image on the screen. 
Blank  on/off  Hide the image, displays a blank, black 
screen*(see below) 
Reset all  execute Resets all OSD Menu function to their factory 
default values*( see below) 
Language English Select the language that the OSD Menu and on 
screen massage are display in English / German 
/ French / Spanish / Italian 
/ Portuguese / 
Dutch / Swedish / Chinese(Simplied-Tranditinal) 
/ Korean / Russian / Japanese 
Resize  4:3 
Select source  execute  Select the input source from: 
Computer 1 / Computer 2 (RGB or YPbPr) 
/ Video / S-Video 
logo on/off on—factory-set logo 
off—blue image only. 
scale mode Normal/TrueProvide the image in its original size. When the 
original image size larger than the screen size 
(1024x768), this projector enters panning mode 
automatically.
  
						

							5.PRESENTATION
Auto ceiling  off/on Automatically inverts the image when 
the projector is turned upside down i.e. 
when the projector is mounted on the 
ceiling 
Front execute Normal projection mode 
Ceiling execute 
Inverts the image vertically, used when 
the projector is mounted upside down 
Rear execute 
Inverts the image horizontally, used when 
projecting onto a rear projection screen 
 
Ceiling and 
Rear execute 
Inverts the image horizontally and vertically, 
used when the projector is mounted upside 
down and projecting onto a rear projection 
screen 
Auto 
Brightness off/on 
Auto detects brightness; it turns to economic 
mode automatically when the brightness is 
low. 
Lamp mode normal 
economic Economic mode reduces the lamp brightness 
economic to extend lamp life and quiet the 
projector 
Lamp  Show Lamp timer 
Reset lamp 
timer 
(optional) execute After changing a new lamp,execute this 
function for reset the Lamp timer. 
(see below) 
Functions of Menu (OSD)
Computer Mode-PRESENTATION Menu
59