Home > Eiki > Projector > Eiki Lc-Xg400 Multimedia Projector Owners Manual

Eiki Lc-Xg400 Multimedia Projector Owners Manual

Here you can view all the pages of manual Eiki Lc-Xg400 Multimedia Projector Owners Manual. The Eiki manuals for Projector are available online for free. You can easily download all the documents as PDF.

Page 61

61
The WARNING indicators show the state of the function which protects the projector. Check the state of the 
WARNING indicators and the POWER indicator to take proper maintenance. 
Warning	Indicators
The	projector	is	shut	down	and	the	WARNING	TEMP.	
indicator	is	blinking	red.
When the temperature inside the projector reaches a 
certain level, the projector will be automatically shut 
down to protect the inside of the projector. The POWER 
indicator is blinking while the projector is being cooled...

Page 62

6
Unplug the AC power cord before cleaning.
Gently wipe the projection lens with a cleaning cloth that 
contains a small amount of non-abrasive camera lens cleaner, 
or use a lens cleaning paper or commercially available air 
blower to clean the lens. 
Avoid using an excessive amount of cleaner. Abrasive 
cleaners, solvents, or other harsh chemicals might scratch 
the surface of the lens.
When the projector is not in use, replace the lens cap.
Cleaning	the	Projector	Cabinet
Unplug the AC power cord...

Page 63

6
Troubleshooting
Before calling your dealer or service center for assistance, check the items below once again.
– Make sure you have properly connected the projector to peripheral equipment as described \
on pages 20–22. 
–  Make sure all equipment is connected to AC outlet and the power is turned on.
–  When the projector does not project an image from the connected computer\
, restart the computer.  
 Problem:   – Solutions
  No power   – Plug the power cord of the projector into the AC outlet....

Page 64

64
    off and wait until condensation evaporates. 
    – Projecting from the excessive slant angle to the screen may cause    
     keystone distortion and partial imperfect focus. See page 18.
  Picture is not bright enough .  – Check if "Contrast" or "Brightness" are adjusted properly See page 42.
 
    – Check if "Image level" is selected properly See page 41.
 
    – Check the LAMP REPLACE indicator. If it lights, the end of lamp life is
 
     approaching. Replace the lamp...

Page 65

65

Appendix
This symbol on the nameplate means the product 
is Listed by Under writers Laboratories Inc. It is 
designed and manufactured to meet rigid U.L. 
safety standards against risk of fire, casualty and 
electrical hazards.
The CE Mark is a Directive 
conformity mark of the European 
Community (EC).
WARNING :
High voltages are used to operate this projector . Do not attempt to open the cabinet .
If problems still persist after following all operating instructions, contact the dealer where you...

Page 66

66

Menu	Tree
Dynamic
RealCinema*Image 1Image 2Image 3
Image
VolumeMuteQuitOn/OffSound0–63
Input
Input 3Auto
Go to System (3)
Go to System (3)
Video 
Go to System (1)
S-video
Standard
Quit
Input 1
Go to System (3)Video
Go to System (1)Input 2 RGB
Go to System (2)Component
Image 4
RGB (PC Analog)
RGB (Scart)
RGB (PC Digital)
RGB (AV HDCP)
Quit
Quit
SySTEM (3)SySTEM (1)
- - - -
Mode 1
Mode 2
XGA 1SECAM
NTSC
Auto
PAL
PAL-M
PAL-N
NTSC4.43
SySTEM (2)
1035i
720p
Auto
1080i
480p
575i
575p
480i
InputH-sync...

Page 67

67

LanguageSetting12 languages provided
Blue/User/BlackAuto 1
Normal
BackgroundLamp control
Quit
Capture
Logo PIN code change
Logo PIN code lock
Quit
Auto 2High
QuitAuto PC adj.
Total dotsHorizontalVertical
Display area HDisplay area VReset
PC Adjust
Yes/No
Clamp
Current mode
Mode free/Store
Quit
Fine sync0–31
Mode 1
H-sync freq.V-sync freq.Quit
NormalTrueWideFull screen
Screen
Logo selectLogoOff/Default/User
Yes/No
On/Off
Eco 1Eco 2
✔Note:
	 •	The	Menu	display	varies	depending	on	the	input	
signal....

Page 68

68

Indicators
Projector ConditionPOWERgreenLAMPred
WARNINGTEMP.red
The projector is off. (The AC power cord is unplugged.)
The projector is in stand-by mode. Press the ON/STAND-BY button to 
turn on the projector.
The projector is operating normally.
The projector is in the Power management mode.
The projector is preparing for stand-by or the projection lamp is 
being cooled down. The projector cannot be turned on until cooling is 
completed and the POWER indicator stops blinking.
The temperature...

Page 69

69

––
––
WARNINGFILTERorange
* When the projection lamp reaches its end of life, the LAMP REPLACE indicator lights yellow. When this indicator lights 
yellow, replace the projection lamp with a new one promptly. Reset the lamp counter after replacing the lamp. See pages 
59–60.
The filter is clogged. Stop using the projector immediately and clean 
or replace the filter (see below).
Projector ConditionPOWERgreen
Indicators
WARNING FILTER indicator
The Filter counter reached a set time. Clean or replace...

Page 70

70

Compatible	Computer	Specifications
Basically this projector can accept the signal from all computers with th\
e V- and H-Frequency mentioned 
below and less than 140 MHz of Dot Clock.
 PC Adjustment is limited when selecting these modes.
Appendix
ON-SCREEN DISPLA yRESOLUTION H-Freq .(kHz)V-Freq .(Hz)
VGA 1640x48031.470 59.880 
VGA 2720x40031.470 70.090 
VGA 3640x40031.470 70.090 
VGA 4640x48037.860 74.380 
VGA 5640x48037.860 72.810 
VGA 6640x48037.500 75.000 
VGA 7640x48043.269 85.000 
MAC...
Start reading Eiki Lc-Xg400 Multimedia Projector Owners Manual

Related Manuals for Eiki Lc-Xg400 Multimedia Projector Owners Manual

All Eiki manuals