Eiki Lc-Xg300l Multimedia Projector Quick Reference Guide

							English
Deutsch
Français
Italiano
Español
(*Models without lens.)
Multimedia Projector 
Quick Reference Guide
MODELLC-XG300/LC-XG250
LC-XG300L
*/LC-XG250L*
Use this book as a reference guide when setting up the projector.
For detailed information about installation, setup, and operation of
the projector, refer to the owner’s manual on the CD-ROM.
READ THE SAFETY INSTRUCTIONS IN THE OWNER’S MANUAL
(CD-ROM) BEFORE USING THE PROJECTOR. 
						

							- 2 -
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK). NO
USER-SERVICEABLE PARTS INSIDE EXCEPT
LAMP REPLACEMENT. REFER SERVICING
TO QUALIFIED SERVICE PERSONNEL.
THIS SYMBOL INDICATES THAT DANGEROUS
VOLTAGE CONSTITUTING A RISK OF ELECTRIC
SHOCK IS PRESENT WITHIN THIS UNIT.
THIS SYMBOL INDICATES THAT THERE ARE
IMPORTANT OPERATING AND MAINTENANCE
INSTRUCTIONS IN THE OWNERS MANUAL
WITH THIS UNIT.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
Before installing and operating the projector, read this
manual thoroughly.
The projector provides many convenient features and 
functions. Operating the projector properly enables you
to manage those features and maintains it in good
condition for many years to come.
Improper operation may result in not only shortening
the product life, but also malfunctions, fire hazard, or
other accidents.
Safety Precaution
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS APPLIANCE TO
RAIN OR MOISTURE.
–This projector produces intense light from the projection
lens. Do not stare directly into the lens as much as
possible, otherwise eye damage could result. Be
especially careful that children do not stare directly into
the beam.
–Install the projector in a proper position. Otherwise it
may result in fire hazard.
–Allowing the proper amount of space on the top, sides,
and rear of the projector cabinet is critical for proper air
circulation and cooling of the unit. The dimension
shown here indicate the minimum space required. If the
projector is to be built into a compartment or similarly
enclosed, these minimum distances must be
maintained.
–Do not cover the ventilation slot on the projector. Heat
build-up can reduce the service life of your projector,
and can also be dangerous.
–If the projector is unused for an extended time, unplug
the projector from the power outlet.
0.7 (20 cm)
1.5 (50 cm)3 (1 m)
1.5 (50 cm)
SIDE and TOPREAR
CAUTION
Not for use in a computer room as defined in the
Standard for the Protection of Electronic Computer/Data
Processing Equipment, ANSI/NFPA 75.
Ne peut être utilisé dans une salle d’ordinateurs telle
que définie dans la norme ANSI/NFPA 75 Standard for
Protection of Electronic Computer/Data Processing
Equipment 
NOTE:This symbol and recycle system are applied only to EU
countries and not applied to the countries in the other
area of the world.
Your EIKI product is designed and
manufactured with high quality
materials and components which can be
recycled and reused.
This symbol means that electrical and
electronic equipment, at their end-of-
life, should be disposed of separately
from your household waste.
Please dispose of this equipment at
your local community waste collection/recycling centre.
In the European Union there are separate collection
systems for used electrical and electronic products.
Please help us to conserve the environment we live in! 
CAUTION ON HANGING FROM THE CEILING
When hanging the projector from the ceil-
ing, clean air intake vents, filters, or top of
the projector periodically with a vacuum
cleaner. If you leave the projector unclean
for a long time, the cooling fans can be
clogged with dust, and it may cause a
breakdown or a disaster.
DO NOT SET THE PROJECTOR IN GREASY, WET, OR
SMOKY CONDITIONS SUCH AS IN A KITCHEN TO PREVENT
A BREAKDOWN OR A DISASTER. IF THE PROJECTOR
COMES IN CONTACT WITH OIL OR CHEMICALS, IT MAY
BECOME DETERIORATED.
To the Owner 
						

							- 3 -
English
All the safety and operating instructions should be read
before the product is operated.
Read all of the instructions given here and retain them for
later use. Unplug this projector from AC power supply
before cleaning. Do not use liquid or aerosol cleaners.
Use a damp cloth for cleaning.
Follow all warnings and instructions marked on the
projector.
For added protection to the projector during a lightning
storm, or when it is left unattended and unused for long
periods of time, unplug it from the wall outlet. This will
prevent damage due to lightning and power line surges.
Do not expose this unit to rain or use near water... for
example, in a wet basement, near a swimming pool, etc...
Do not use attachments not recommended by the
manufacturer as they may cause hazards.
Do not place this projector on an unstable cart, stand, or
table. The projector may fall, causing serious injury to a
child or adult, and serious damage to the projector. Use
only with a cart or stand recommended by the
manufacturer, or sold with the projector. Wall or shelf
mounting should follow the manufacturer’s instructions,
and should use a mounting kit approved by the
manufacturers.
An appliance and cart combination
should be moved with care. Quick
stops, excessive force, and uneven
surfaces may cause the appliance
and cart combination to overturn.
Slots and openings in the back and bottom of the cabinet
are provided for ventilation, to ensure reliable operation of
the equipment and to protect it from overheating.
The openings should never be covered with cloth or other
materials, and the bottom opening should not be blocked
by placing the projector on a bed, sofa, rug, or other
similar surface. This projector should never be placed near
or over a radiator or heat register.
This projector should not be placed in a built-in installation
such as a book case unless proper ventilation is provided.
Never push objects of any kind into this projector through
cabinet slots as they may touch dangerous voltage points
or short out parts that could result in a fire or electric
shock. Never spill liquid of any kind on the projector.Do not install the projector near the ventilation duct of air-
conditioning equipment.
This projector should be operated only from the type of
power source indicated on the marking label. If you are
not sure of the type of power supplied, consult your
authorized dealer or local power company.
Do not overload wall outlets and extension cords as this
can result in fire or electric shock. Do not allow anything
to rest on the power cord. Do not locate this projector
where the cord may be damaged by persons walking on
it.
Do not attempt to service this projector yourself as
opening or removing covers may expose you to
dangerous voltage or other hazards. Refer all servicing to
qualified service personnel.
Unplug this projector from wall outlet and refer servicing
to qualified service personnel under the following
conditions:
a. When the power cord or plug is damaged or frayed.
b. If liquid has been spilled into the projector.
c. If the projector has been exposed to rain or water.
d. If the projector does not operate normally by following
the operating instructions. Adjust only those controls
that are covered by the operating instructions as
improper adjustment of other controls may result in
damage and will often require extensive work by a
qualified technician to restore the projector to normal
operation.
e. If the projector has been dropped or the cabinet has
been damaged.
f. When the projector exhibits a distinct change in
performance-this indicates a need for service.
When replacement parts are required, be sure the service
technician has used replacement parts specified by the
manufacturer that have the same characteristics as the
original part. Unauthorized substitutions may result in fire,
electric shock, or injury to persons.
Upon completion of any service or repairs to this
projector, ask the service technician to perform routine
safety checks to determine that the projector is in safe
operating condition.
Voor de klanten in Nederland
Bij dit produkt zijn batterijen
geleverd.
Wanneer deze leeg zijn, moet u
ze niet weggooien maar inleveren
als KCA.
NL
Safety Instructions 
						

							- 4 -
Openings in the cabinet are provided for ventilation.
To ensure reliable operation of the product and to
protect it from overheating, these openings must not
be blocked or covered. 
CAUTION
Hot air is exhausted from the exhaust vent. When
using or installing the projector, the following
precautions should be taken. 
–Do not put any flammable object or spray can near
the projector, hot air is exhausted from the air
vents.
–Keep the exhaust vent at least 3’ (1 m) away from
any objects.
–Do not touch peripheral parts of the exhaust vent,
especially screws and metallic parts. This area will
become hot while the projector is being used.
–Do not put anything on the cabinet. Objects put on
the cabinet will not only get damaged but also may
cause fire hazard by heat.
Cooling fans are provided to cool down the projector.
The fans’ running speed is changed according to the
temperature inside the projector.
Air Circulation
The projector uses a lamp which generates significant
heat. The cooling fans and air vents are provided to
dissipate the heat by drawing air into the housing and
the filter is located in the intake vents to prevent dust
from getting inside of the projector.
In order to care for the projector appropriately, regular
cleaning is required. Remove any dirt or dust that has
accumulated on the projector and on or in the filter.
If the projector detects that the filter is clogged, a
“Filter warning” icon (red) will appear on the screen
and “WARNING FILTER” indicator on the top panel
will blink (see below). Stop using the projector
immediately and clean or replace the filter.
Blocking the air vents and leaving the projector
uncleaned for a long time may not only damage the
projector and may require costly repairs but may also
cause accidents or fire.
Damages to the projector caused by using an
uncleaned filter or improper maintenance will void
the warranty on the projector.
IMPORTANT!
Clean the Filter Regularly!!
Filter warning icon (red) appears on the screen
when the projector detects filter clogging.
Top Control
WARNING FILTER
indicator
Exhaust Vent
(Hot air exhaust)
Air Intake Vent
Air flow 
						

							- 5 -
English10˚ 10˚
10˚10˚
Do not tilt the projector more than 10 degrees from side to side. 
In upward projection, do not tilt the projector over 10 degrees right and left.
Do not put the projector on either side to project an image. 
10˚
10˚
In downward projection, do not tilt the projector over 10 degrees right and left.
Use the projector properly in specified positions. Improper positioning may reduce the lamp life and result in
severe accident or fire hazard.
This projector can project the picture upward, downward, or backward, perpendicular to the plane of the screen
as shown in the figure below.
Bottom
Downward
(Usual)Front
DownwardBottom
UpwardFront
Upward
Installing the Projector in Proper Directions
Avoid positioning the projector as described below when installing.
Positioning Precautions
CAUTION
Make sure that the Fan control settings
are set properly when setting up the
projector with upward/downward
inclination of over 20 degrees to the
horizontal plane. 
						

							- 6 -
Use the hand grip when moving the projector.
Replace the lens cap and retract the adjustable feet to
prevent damage to the lens and cabinet when carrying. 
When the projector is not in use for an extended period, put
it into a suitable case to protect the projector.
CAUTION IN CARRYING OR
TRANSPORTING THE PROJECTOR
–Do not drop or bump the projector, otherwise damages
or malfunctions may result.
–When carrying the projector, use a suitable carrying
case.
–Do not transport the projector by courier or any other
transport service in an unsuitable transport case. This
may cause damage to the projector. For information
about transporting the projector by courier or any other
transport service, consult your dealer.
–Do not put the projector in a case before it is cooled
enough.
Cautions in Handling the Projector
Do not hold the lens when lifting or moving the projector.
Doing so may cause damage to the lens and the projector. 
Care must be taken when handling the projector; do not
drop, bump, subject it to strong forces, or put other things
on the cabinet.
CAUTION
This projector has a motorized lens. Please note
the followings when using the projector.
●Do not touch the lens while it is moving as this
could cause injury to the fingers.
●Never allow children to touch the lens.
Moving the Projector
Do not hold the lens and the peripheral part. 
						

							- 7 -
English
Bottom Back
qFilter
wSpeaker
eLens Release Button
rTop Controls and Indicators
tMaintenance Cover
WARNING: FOR MAINTENANCE USE
ONLY. DO NOT OPEN.
yLens Cap 
(for LC-XG300/XG250)
!7
!4!6!5
!2
!3
CAUTION
Hot air is exhausted from the exhaust vent.
Do not put heat-sensitive objects near this
side.
o
!1Infrared Remote Receiver (Back)
!2Terminals and Connectors
!3Lamp Cover
!4Power Cord Connector
!5Optional Parts Attachment
!6Air Intake Vent
!7Hand Grip
CAUTION
Do not turn on the projector with the lens
cap attached. High temperature from light
beam may damage the lens cap and result
in fire hazard.
uInfrared Remote Receiver (Front)
iProjection Lens
(for LC-XG300/XG250)
oAdjustable Feet
!0Exhaust Vent
✽Kensington Security Slot
This slot is for a Kensington lock used to deter
theft of the projector.
*Kensington is a registered trademark of ACCO Brands 
Corporation.
!1
u
e
rt
y
Front
!0o
qw
i✽ 
						

							- 8 -
Rear Terminal
qwe
r
t
yiu
tUSB CONNECTOR (Series B)
Use this connector when controlling a computer
with the remote control of the projector. Connect
the USB terminal of your computer to this
connector with the supplied USB cable.
yS-VIDEO INPUT JACK
Connect the S-VIDEO output signal from video
equipment to this jack.
iAUDIO 2 JACK
Connect the audio output (stereo) signal from a
computer or video equipment to this jack.
oAUDIO 1 JACK
Connect the audio output (stereo) signal from a
computer or video equipment to this jack.rVIDEO INPUT JACK
Connect the composite video output signal from
video equipment to this jack.
uAUDIO 3 JACKS (L(MONO)/R)
Connect the audio output signal from video
equipment to these jacks. For a mono audio signal
(a single audio jack), connect to the Mono input
jack.
q5 BNC INPUT JACKS
Connect the component or composite video output
signal from video equipment to VIDEO/Y, Cb/Pb,
and Cr/Pr jacks or connect the computer output
signal (5 BNC Type [Green, Blue, Red, Horiz. Sync,
and Vert. Sync.]) to G, B, R, H/V, and V jacks.
wCOMPUTER INPUT TERMINAL (ANALOG)
Connect the computer (or RGB scart) output signal
to this terminal.
eCOMPUTER INPUT TERMINAL (DIGITAL)
Connect the computer output signal (Digital DVI-D
type) to this terminal. The HD (HDCP compatible)
signal can also be connected.
o 
						

							- 9 -
English
!0R/C JACK
When using the wired remote control, connect the
wired remote control to this jack with a remote
control cable (not supplied).
!2MONITOR OUTPUT TERMINAL (ANALOG)
This terminal outputs the video signal from
computer to external video equipment.
✽RESET button
A built-in micro processor which controls this unit may
occasionally malfunction and need to be reset. This can be
done by pressing the RESET button with a pen, which will
shut down and restart the unit.  Do not use the RESET
function excessively.
Rear Terminal
!0!1!2!3!4✽
!1AUDIO MONITOR OUTPUT JACK (VARIABLE)
This jack outputs the audio signal from computer
or video equipment to external audio equipment.
!3CONTROL PORT CONNECTOR
When controlling the projector from a computer,
connect the computer to this connector with a
control cable.
!4Infrared Remote Receiver (Back)
The infrared remote receiver is also located in the
front. 
						

							- 10 -
q
w
e
t
u
i
o
wLAMP REPLACE indicator
Lights yellow when the projection lamp reaches its
end of life.
qWARNING TEMP. indicator
Blinks red when the internal temperature of the
projector exceeds the operating range.
eON/STAND-BY button
Turn the projector on or off.
rINPUT button
Select an input source.
!1INFO. button
Display the input source information.
yPOINT ed7 8(VOLUME +/–) buttons
–Select an item or adjust the value in the On-
Screen Menu.
–Pan the image in Digital zoom + mode.
–Adjust the volume level (Point 
7 8buttons).
uSELECT button
–Execute the selected item.
–Expand or compress the image in the Digital zoom
mode.
Top Control
r
y
!0
!1
!2
tLENS button
Enter the focus, zoom, and lens shift adjustment
mode.
iWARNING FILTER indicator
–Blinks orange indicating the filter needs cleaning.
–Lights orange when clogging of the filter is
detected, urging immediate cleaning.
oLAMP indicator
Lights red during operations.
!0POWER indicator
–Lights when in stand-by mode and during
operations.
–Blinks during the cooling-off period.
–Blinks in the Power management mode.
!2MENU button
Open or close the On-Screen Menu.
✔Note:
•All five indicators on the top control blinks when the
projector detects an abnormal condition.