Eiki Eip-1600t Dlp Projector Owners Manual

57
Connecting Pin Assignments
COMPUTER-RGB Input COMPUTER-RGB/COMPONENT INPUT5 Terminal: 15-pin Mini D-sub female connector
1. Video input (red)
2. Video input (green/sync on green)
3. Video input (blue)
4. Not connected
5. Not connected
6. Earth (red)
7. Earth (green/sync on green)
8. Earth (blue)
9. Not connected
10. GND
11. Not connected
12. Bi-directional data
13. Horizontal sync signal: TTL level
14. Vertical sync signal: TTL level
15. Data clock
RS-232C Terminal: 9-pin Mini DIN female...

58
RS-232C Specifications and Command Settings
Computer control
A computer can be used to control the projector by connecting an RS-232C serial control cable
(cross type, sold separately) to the projector. (See page 27 for connection.)
Communication conditions
Set the serial port settings of the computer to match that of the table.
Signal format: Conforms to RS-232C standard. Parity bit: None
Baud rate: * 9,600 bps/115,200 bps Stop bit: 1 bit
Data length: 8 bits Flow control: None
* Set the...

59
DTV
•When this projector receives 640K350 VESA format VGA signals, “640K400” appears on the screen.
Computer
Computer Compatibility Chart
• Multiple signal support
Horizontal Frequency: 15-70 kHz,
Vertical Frequency: 45-85 Hz,
Pixel Clock: 12-85 MHz
Sync signal: Compatible with TTL level
The following is a list of modes that conform to VESA. However, this projector supports other
signals that are not VESA standards.
27.0
31.5
37.5
27.0
31.5
37.9
27.0
31.5
27.0
31.5
37.9
26.2
31.5
34.7
37.9
37.5
43.3...

60
Troubleshooting
Picure does not appear
or projector does not
start.
No picture appears (or
picture is dark).
Color is faded or poor.
Picture is blurred;
noise appears.Problem Check
• Projector power cord is not plugged into the wall outlet.
• Power to the external connected devices is off.
• The selected input mode is wrong.
• Cables incorrectly connected to the projector.
• Remote control battery has run out.
• External output has not been set when connecting notebook
computer.
• The lamp unit cover...

61
Problem
Picture is too bright and
whitish.
The black levels of the
image show banding or
appear faded when
INPUT 6 is selected.
The cooling fan becomes
noisy.
The lamp does not light
up even after the
projector turns on.
The lamp suddenly turns
off during projection.
The image sometimes
flickers.
The lamp needs much
time to turn on.
Picture is dark.Check
• Image adjustments are incorrectly set.
• Select the HDMI Setting (“Standard” or “Enhanced”) that results in
the best picture quality.
• When...

62
Specifications
Projector
EIP-1600T
NTSC3.58/NTSC4.43/PAL/PAL-M/PAL-N/PAL-60/SECAM/DTV480I/DTV480P/
DTV540P/DTV576I/DTV576P/DTV720P/DTV1035I/DTV1080I/DTV1080I-50
Single Chip Digital Micromirror Device
TM (DMDTM) by Texas InstrumentsPanel size: 0.65", 1chip DMD
Drive method: Digital Light Processing (DLP™)
No. of dots: 983,040 dots (1280 [H] × 768 [V])
1–1.15× zoom lens, F2.4–2.6, f = 19.0–21.9 mm
275 W DC lamp
RCA connector
Y: 1.0 Vp-p, sync negative, 75 Ω terminated
P
B (CB): 0.7 Vp-p, 75 Ω...

63
Dimensions
Units: inches (mm)
M4
M4
M4
M4
31577.5
65.5 46.2 80
47 73
7533.8
109105
47.5 104 11280 95 11 

64
AC socket ....................................................... 28
Accessories................................................... 10
Adjustment buttons ........................................ 41
Aspect ratio .................................................... 36
Auto Power Off ............................................... 49
Auto Sync
(Auto Sync adjustment) .............................. 46
AUTO SYNC button ....................................... 46
Background...

A-Key to better communications
U.S.A.EIKI International, Inc.
30251 Esperanza
Rancho Santa Margarita
CA 92688-2132
U.S.A.
Tel : 800-242-3454 (949)-457-0200
Fax : 800-457-3454 (949)-457-7878
E-Mail : [email protected]
Deutschland & ÖsterreichEIKI Deutschland GmbH
Am Frauwald 12
65510 Idstein
Deutschland
Tel : 06126-9371-0
Fax : 06126-9371-14
E-Mail : [email protected]
CanadaEIKI CANADA - Eiki International, Inc.
P.O. Box 156, 310 First St. - Unit 2,
Midland, ON, L4R 4K8, Canada
Tel : 800-563-3454 (705)-527-4084
Fax...