Eiki Eip-1600t Dlp Projector Owners Manual

47
Using the “Options” Menu
Image Shift
Overscan H
Overscan V0
0
Subtitle00
OSD Display
On Options 1 INPUT 1
h 0 Lamp Timer(Life) 100% Video System
Auto
Signal Type
Auto
HDMI Setting
Standard
Background
Blue
Auto Power Off
On
1
2
3
2
4
5
6
7
8
9
0
Menu operation n Page 41
1 11 1
1Adjusting the Image
Position
You can move the projected image vertically.
• The Image Shift function cannot be selected
when “Resize” is set to “DOT BY DOT”.
• You can also use the IMAGE SHIFT buttons
on the remote control to...

48
Menu operation n Page 41
6 66 6
6 Signal Type Setting
Using the “Options” Menu (Continued)
This function allows you to select the input sig-
nal type (RGB or Component) for INPUT 5 or
INPUT 6.
Selectable items
Auto
RGB
ComponentDescription
Automatically selects the
appropriate input signal
between RGB and Component.
Set when RGB signals are
received.
Set when component signals
are received.
5 55 5
5Setting the Video
System
This function can only be set in INPUT 3 or
INPUT 4.
The video input system...

49
Options 2 INPUT 1
STANDBY Mode
Eco
Fan Mode
Normal RS-232C
9600 bps PRJ Mode
Front
All reset
Language
English6 5 4 3 2
1
Menu operation n Page 41
Settings on the Options 2 menu
Selectable items
Front
Ceiling + Front
Rear
Ceiling + RearDescription
Normal image (Projected from
the front of the screen)
Inverted image (Projected
from the front of the screen
with an inverted projector)
Reversed image (Projected
from the rear of the screen or
with a mirror)
Reversed and inverted image
(Projected with a...

50
Using the “Options” Menu (Continued)
2 22 2
2Selecting the Transmission
Speed (RS-232C)
Make sure that both the projector and computer
are set for the same baud rate.
Selectable
items
9600bps
115200bpsDescription
Transmission speed is slow.
Transmission speed is rapid.
P
R
4 44 4
4 Fan Mode Setting
This function changes the fan rotation speed.
Selectable
items
Normal
HighDescription
Suitable for normal environments.
Select this when using the projector at
altitudes of approximately 4,900 feet
(1,500...

51
Cleaning the lens■Use a commercially available blower or lens
cleaning paper (for glasses and camera lenses)
for cleaning the lens. Do not use any liquid type
cleaning agents, as they may wear off the
coating film on the surface of the lens.
■As the surface of the lens can easily get
damaged, be sure not to scrape or hit the lens.
Cleaning the exhaust and intake vents■Use a vacuum cleaner to clean dust from the
exhaust vent and the intake vent.
Cleaning the projector■Ensure that you have unplugged the...

52
Maintenance Indicators
About the lamp indicator
■When the remaining lamp life becomes 5% or less,  (yellow) and “Change The Lamp” will be
displayed on the screen. When the percentage becomes 0%, it will change to  (red), the lamp will
automatically turn off and then the projector will automatically enter standby mode. At this time, the
lamp indicator will illuminate in red.
■If you try to turn on the projector a fourth time without replacing the lamp, the projector will
not turn on.
About the...

53
• If the temperature warning indicator illuminates, and the projector enters standby mode, follow the
possible solutions above and then wait until the projector has cooled down completely before plug-
ging in the power cord and turning the power back on. (At least 10 minutes.)
• If the power is turned off for a brief moment due to power outage or some other cause while using
the projector, and the power supply recovers immediately after that, the lamp indicator will illumi-
nate in red and the lamp...

54
Regarding the Lamp
Lamp■It is recommended that the lamp (sold separately) be replaced when the remaining lamp life becomes
5% or less, or when you notice a significant deterioration in the picture and color quality. The lamp life
(percentage) can be checked with the on-screen display. (see page 49)
■Purchase a replacement lamp of type AH-11201 from your place of purchase, nearest EIKI Authorized
Dealer or Service Center.
Caution Concerning the Lamp■This projector utilizes a pressurized mercury lamp. A...

55
Removing and Installing the
Lamp Unit
• Make sure that you remove the lamp unit by
the handle. Do not touch the glass surface of
the lamp unit or the inside of the projector.
• To avoid injury to yourself and damage to the
lamp, be sure to carefully follow the steps
below.
• Do not loosen other screws except for the
lamp unit cover and lamp unit.
PressoSTANDBY-ON on the pro-
jector or aSTANDBY on the re-
mote control to put the projector
into standby mode.
• Wait until the cooling fan stops....

56
Regarding the Lamp (Continued)
Remove the lamp unit.• Loosen the securing screws from the
lamp unit. Hold the lamp unit by the
handle and pull it in the direction of the
arrow. At this time, keep the lamp unit
horizontal and do not tilt it.
Resetting the Lamp Timer
Reset the lamp timer after replacing the lamp.
Insert the new lamp unit.• Press the lamp unit firmly into the lamp
unit compartment. Fasten the securing
screws.
Replace the lamp unit cover.• Align the tab on the lamp unit cover (1)
and...