Eiki Efd 46 Owners Manual

9
Part Names
Front view
LCD panel
POWER indicator (See page 22.)
TIMER indicator (See page 41.)
OPC indicator (See page 31.)
OPC sensor (See page 31.)
Remote control sensor (See page 21.)
Rear view
CAUTION
The area surrounding these terminals 
gets hot. Exercise due caution when 
handling. (EFD-46 only)
HOTLAN
terminal
(See page 19.)
RS-232C
terminal
(See page 19.)
HDMI
terminal
(See page 16.) DVI IN 
terminals
(See pages 
15,16and17.)AC input terminal 
(See page 20.)
COMPUTER IN 1 terminals (See pages...

10
Part Names
Side view
POWER button
For turning the main power on. 
(See page 22.)
MENU button
For displaying adjustment and setting screens. 
(See page 28.)
ENTER button
For setting items selected or adjusted on the menu. 
(See page 28.)
INPUT buttons (
/)
For selecting the input mode. 
(See page 23.)
VOL (Volume) buttons (+/–) 
For adjusting the speaker sound level. 
(See page 23.)
Adjustment buttons (
x
/
z
/
{
/
y
)
For selecting and adjusting menu items. 
(See page 28.)
S-VIDEO IN terminal 
(See...

11
Remote control
ON button
For turning the power on.
(See page 22.)
COMPUTER 1, COMPUTER 2, DVI, 
HDMI, S-VIDEO, VIDEO buttons
For switching to the respective input 
modes.
(See page 23.)
AV MUTE button
For temporarily displaying a black 
screen and turning off the sound.
(See page 23.)
VOL (Volume) buttons (+/–)
For adjusting the speaker sound level.
(See page 23.)
MENU button 
For displaying adjustment and setting 
screens.
(See page 28.)
ENTER button
For setting items selected or adjusted 
on the...

12
How to Install the Monitor
Mounting precautions
•  Mounting the monitor on the wall requires special expertise and the work must be performed by an 
authorized EIKI dealer. You should never attempt to perform any of this work yourself. Our company will 
bear no responsibility for accidents or injuries caused by improper mounting or mishandling.
•  This monitor is designed to be installed on a concrete wall or pillar. Reinforced work might be necessary 
for some materials such as plaster / thin plastic...

13
How to Install the Monitor
56
Insert and tighten the screws into the 4 holes on 
the rear of the monitor. Insert the stand into the openings on the 
underside of the monitor.
• To detach the stand, perform the steps in reverse order.
• Store the protective covers. You will need them after detaching the stand.
Note
Mounting the monitor on the wall
„ Handling and precautions with the wall-mounted monitor
•  You can mount the monitor on the wall using the optional WB-EF5201 bracket.
•  For details, refer...

14
„ Mounting the monitor on the wall
Attach the monitor to the wall-mount brackets according to the procedure below.
12
Use the protective cover to prevent dust from 
entering the underside of the monitor where the 
stand has been detached.
3
6
Unfasten the 4 screws used to secure the stand in 
place.
Connect and bind the power cord and terminal 
cables. Detach the 4 caps at the 4 locations on the rear of 
the monitor.
Attach the wall-mount brackets (L/R).
54
Set the monitor on the wall.
How to Install...

15
Connecting Peripheral Equipment
Caution
•  Be sure to turn off the power and disconnect the plug from the power outlet before connecting/
disconnecting cables. Also, read the manual of the equipment to be connected.
•  Be careful not to mix up the input terminal with the output terminal when connecting cables. Mixing up the 
input and output terminals may cause malfunctions and other problems.
•  After making all connections, turn on the monitor and then the other pieces of equipment. When 
connecting...

16
EquipmentTerminal on connected 
equipmentCable (commercially available)Terminal on the 
monitor
Video equipment
DVI digital output 
terminalDVI Digital cableDVI IN
DVI-D
(HDCP)
Component video 
output terminal3 RCA to mini D-sub 15 pin cable COMPUTER IN 1
S-video output 
terminalS-video cableS-VIDEO IN
Video output 
terminalVideo cableVIDEO IN
HDMI output 
terminalHDMI cable HDMI
RGB output 
terminal5 RCA RGB cable 
BNC to RCA adaptorsCOMPUTER IN 2
Component
video output 
terminalBNC to RCA adaptors...

17
EquipmentTerminal on connected 
equipmentCable (commercially available)Terminal on the 
monitor
Camera/Video gameComponent
video output 
terminalCables for a camera or a video game/
3 RCA to mini D-sub 15 pin cable
RCA adaptor plug
COMPUTER IN 1
S-video output 
terminalCables for a camera or a video gameS-VIDEO IN
Video output 
terminalCables for a camera or a video gameVIDEO IN
Audio equipmentø3.5 mm audio 
output terminalø3.5 mm stereo or mono audio cableAUDIO (for DVI IN)
AUDIO
AUDIO
(for COMPUTER...

18
Connecting Peripheral Equipment
Connecting external speakers
Be sure to use external speakers with an impedance 
of 4 
 and a rated input of at least 15 W.
1  While pushing the tab, insert the tip of the cable.
2  Release the tab.
• Be sure to connect the + and - terminals and the left and 
right speakers properly.
• Avoid short circuiting the + and - terminals.
• It is recommended that you use the optional EIKI speaker 
unit (SP-EF5201/SP-EF4601) for external speakers.
Note
Connecting multiple...