Eiki Efd 46 Owners Manual

							9
Part Names
Front view
LCD panel
POWER indicator (See page 22.)
TIMER indicator (See page 41.)
OPC indicator (See page 31.)
OPC sensor (See page 31.)
Remote control sensor (See page 21.)
Rear view
CAUTION
The area surrounding these terminals 
gets hot. Exercise due caution when 
handling. (EFD-46 only)
HOTLAN
terminal
(See page 19.)
RS-232C
terminal
(See page 19.)
HDMI
terminal
(See page 16.) DVI IN 
terminals
(See pages 
15,16and17.)AC input terminal 
(See page 20.)
COMPUTER IN 1 terminals (See pages 15,16and17.)COMPUTER IN 2 terminals (See pages 15,16and17.)MONITOR OUT terminals (See page 17.)SPEAKER OUT terminals (See page 18.)
Handles (Fixed type)
• The illustrations in this owner’s manual are for explanation purposes and may vary slightly from the actual operations.
• The illustrations used throughout this manual are based on EFD-52.
Note
 
						

							10
Part Names
Side view
POWER button
For turning the main power on. 
(See page 22.)
MENU button
For displaying adjustment and setting screens. 
(See page 28.)
ENTER button
For setting items selected or adjusted on the menu. 
(See page 28.)
INPUT buttons (
/)
For selecting the input mode. 
(See page 23.)
VOL (Volume) buttons (+/–) 
For adjusting the speaker sound level. 
(See page 23.)
Adjustment buttons (
x
/
z
/
{
/
y
)
For selecting and adjusting menu items. 
(See page 28.)
S-VIDEO IN terminal 
(See pages 16and17.)
VIDEO IN terminal 
(See pages 16and17.)
AUDIO terminals 
(See page 17.)
 
						

							11
Remote control
ON button
For turning the power on.
(See page 22.)
COMPUTER 1, COMPUTER 2, DVI, 
HDMI, S-VIDEO, VIDEO buttons
For switching to the respective input 
modes.
(See page 23.)
AV MUTE button
For temporarily displaying a black 
screen and turning off the sound.
(See page 23.)
VOL (Volume) buttons (+/–)
For adjusting the speaker sound level.
(See page 23.)
MENU button 
For displaying adjustment and setting 
screens.
(See page 28.)
ENTER button
For setting items selected or adjusted 
on the menu.
(See page 28.)
RETURN button 
For returning to the previous menu 
screen during menu operations.
(See page 28.)
SELECT button
For selecting either screen to be active 
in split-screen mode.
(See page 27.)AV MODE button
For selecting appropriate settings for 
picture and audio.
(See page 26.) RESIZE button
For switching the picture size.
(See page 24.)STANDBY button
For putting the monitor into 
the standby mode.
(See page 22.)
FREEZE button
For freezing images.
(See page 26.)
MAGNIFY buttons
For enlarging/reducing part of 
the image.
(See page 26.)
Adjustment buttons 
(
x
/
z
/
{
/
y
)
For selecting and adjusting 
menu items.
(See page 28.)
P&P button
For setting the split-screen picture 
mode. Press P&P again to return to 
normal view.
(See page 27.)
AUTO SYNC button
For automatically adjusting images 
when connected to a computer.
(See page 26.)
Part Names
 
						

							12
How to Install the Monitor
Mounting precautions
•  Mounting the monitor on the wall requires special expertise and the work must be performed by an 
authorized EIKI dealer. You should never attempt to perform any of this work yourself. Our company will 
bear no responsibility for accidents or injuries caused by improper mounting or mishandling.
•  This monitor is designed to be installed on a concrete wall or pillar. Reinforced work might be necessary 
for some materials such as plaster / thin plastic board / wood before starting installation.
This monitor and bracket must be installed on a wall which can endure at least 4 times or more the weight 
of the monitor. Install by the most suitable method for the material and the structure.
•  This monitor can not be installed in a vertical orientation.
•  Since the monitor is heavy, consult your dealer before installing, removing or moving the monitor.
•  When installing, removing or moving the monitor, ensure that this is carried out by at least 2 people.
•  When moving the monitor, be sure to hold it with the handles both on the rear and the unit bottom. Do not 
hold the LCD panel. This may cause product damage, failure, or injury.
•  This monitor should be used at an ambient temperature between 32°F (0°C) and 104°F 
(40°C). Provide enough space around the monitor to prevent heat from accumulating inside.
•  Do not block any ventilation openings. If the temperature inside the monitor rises, this could lead to a 
malfunction.
•  Do not place the monitor on a device which generates heat.
Attaching the setup stand
Before performing work spread cushioning over the base area to lay the monitor on. This will prevent it from 
being damaged.
Caution
•  Please note that the setup stand is for temporary use only until the monitor is properly mounted.
•  Attach the stand in the correct direction.
•  Be sure to follow the instructions. Incorrect installation of the stand may result in the monitor falling over.
Remove the protective covers from the underside 
of the monitor.
12
Put the caps on the screws that have been 
screwed into the stand.Assemble the stand using the 6 screws. 
34
Confi rm that there are 10 screws and 6 caps 
supplied with the stand.
 
						

							13
How to Install the Monitor
56
Insert and tighten the screws into the 4 holes on 
the rear of the monitor. Insert the stand into the openings on the 
underside of the monitor.
• To detach the stand, perform the steps in reverse order.
• Store the protective covers. You will need them after detaching the stand.
Note
Mounting the monitor on the wall
„ Handling and precautions with the wall-mounted monitor
•  You can mount the monitor on the wall using the optional WB-EF5201 bracket.
•  For details, refer to the instructions supplied with the optional WB-EF5201 bracket.
Caution
•  This monitor should be mounted on the wall only with the WB-EF5201 (EIKI) wall-mount bracket. The use 
of other wall-mount brackets may result in an unstable installation and may cause serious injuries.
•  Installing the monitor requires special skill that should only be performed by qualifi ed service personnel. 
Customers should not attempt to do the work themselves. EIKI bears no responsibility for improper 
mounting or mounting that results in accident or injury.
Using an EIKI recommended bracket to mount the monitor
•  You can ask a qualifi ed service professional about using an EIKI recommended WB-EF5201 bracket to 
mount the monitor to the wall.
•  Carefully read the instructions that come with the bracket before beginning work.
Hanging on the wall
WB-EF5201 wall-mount bracket. (See the bracket instructions for details.)
WB-EF5201 Vertical mounting Angular mountingAbout setting the monitor angle
•  The center of the display
 EFD-52: 
  The “f ” position is at the center 
of the display.
 EFD-46: 
  The “b” position is at the center 
of the display.
•  Refer to the owner’s manual of 
WB-EF5201 for details.0°/5°/10°/15°/20°
 
						

							14
„ Mounting the monitor on the wall
Attach the monitor to the wall-mount brackets according to the procedure below.
12
Use the protective cover to prevent dust from 
entering the underside of the monitor where the 
stand has been detached.
3
6
Unfasten the 4 screws used to secure the stand in 
place.
Connect and bind the power cord and terminal 
cables. Detach the 4 caps at the 4 locations on the rear of 
the monitor.
Attach the wall-mount brackets (L/R).
54
Set the monitor on the wall.
How to Install the Monitor
 
						

							15
Connecting Peripheral Equipment
Caution
•  Be sure to turn off the power and disconnect the plug from the power outlet before connecting/
disconnecting cables. Also, read the manual of the equipment to be connected.
•  Be careful not to mix up the input terminal with the output terminal when connecting cables. Mixing up the 
input and output terminals may cause malfunctions and other problems.
•  After making all connections, turn on the monitor and then the other pieces of equipment. When 
connecting a computer, ensure that it is the last equipment to be turned on after all the connections are 
made.
•  You may need other cables or connectors not listed below.
S-VIDEO IN
VIDEO IN
AUDIO
COMPUTER IN 1 COMPUTER IN 2 MONITOR OUT
HDMI
DVI IN
EquipmentTerminal on connected 
equipmentCable (commercially available)Terminal on the 
monitor
Computer
RGB output 
terminalRGB cableCOMPUTER IN 1
RGB output 
terminal5 BNC to 15-pin D-sub cableCOMPUTER IN 2
DVI digital output
terminalDVI Digital cable DVI IN
DVI-D
(HDCP)
• Images may not be displayed properly depending on the computer (graphics board) to be connected.
• See page 46
 “Computer compatibility chart” for a list of computer signals compatible with the monitor. 
Use with computer signals other than those listed may cause some of the functions to not work.
•  A Macintosh adaptor may be required for use with some Macintosh computers. Contact your nearest Macintosh Dealer.
• Depending on the computer you are using, an image may not be displayed unless the computer’s external output port is 
switched on. Refer to the specifi c instructions in the owner’s manual of your computer to enable your computer’s external 
output port.
Note
 
						

							16
EquipmentTerminal on connected 
equipmentCable (commercially available)Terminal on the 
monitor
Video equipment
DVI digital output 
terminalDVI Digital cableDVI IN
DVI-D
(HDCP)
Component video 
output terminal3 RCA to mini D-sub 15 pin cable COMPUTER IN 1
S-video output 
terminalS-video cableS-VIDEO IN
Video output 
terminalVideo cableVIDEO IN
HDMI output 
terminalHDMI cable HDMI
RGB output 
terminal5 RCA RGB cable 
BNC to RCA adaptorsCOMPUTER IN 2
Component
video output 
terminalBNC to RCA adaptors 
Component video cable
• Depending on specifi cations of video equipment or HDMI to DVI digital cable, the signal transmission may not work properly. 
(The HDMI specifi cation does not support all connections to video equipment that has HDMI digital output terminal using 
HDMI to DVI digital cable.)
• For details on compatibility for connection, see support information on DVI connection provided by the video equipment 
manufacturer.
•  When you connect video equipment with a 21-pin RGB output (Euro-scart) to the monitor, use a commercially available cable 
that fi ts in the monitor terminal you want to connect.
• The monitor does not support RGBC signals via the Euro-scart.
Note
Connecting Peripheral Equipment
 
						

							17
EquipmentTerminal on connected 
equipmentCable (commercially available)Terminal on the 
monitor
Camera/Video gameComponent
video output 
terminalCables for a camera or a video game/
3 RCA to mini D-sub 15 pin cable
RCA adaptor plug
COMPUTER IN 1
S-video output 
terminalCables for a camera or a video gameS-VIDEO IN
Video output 
terminalCables for a camera or a video gameVIDEO IN
Audio equipmentø3.5 mm audio 
output terminalø3.5 mm stereo or mono audio cableAUDIO (for DVI IN)
AUDIO
AUDIO
(for COMPUTER IN 1)
(for COMPUTER IN 2)
RCA audio output 
terminalRCA audio cableAUDIO 
(for S-VIDEO IN) 
(for VIDEO  IN)
Audio output 
terminalCables for a camera or a video game
MonitorRGB input 
terminalRGB cableMONITOR OUT
Amplifi erø3.5 mm audio 
input terminalø3.5 mm stereo or mono audio cableAUDIO (for MONITOR OUT)
RCA audio input 
terminalø3.5 mm stereo minijack to RCA audio 
cable
• When using the ø3.5 mm mono audio cable, the volume level will be half of when using the ø3.5 mm stereo audio cable.
Note
MONITOR OUT terminals 
•  Audio and images from equipment connected to the COMPUTER IN 1 or COMPUTER IN 2 terminals can 
be output from the MONITOR OUT terminals.
Connecting Peripheral Equipment
 
						

							18
Connecting Peripheral Equipment
Connecting external speakers
Be sure to use external speakers with an impedance 
of 4 
 and a rated input of at least 15 W.
1  While pushing the tab, insert the tip of the cable.
2  Release the tab.
• Be sure to connect the + and - terminals and the left and 
right speakers properly.
• Avoid short circuiting the + and - terminals.
• It is recommended that you use the optional EIKI speaker 
unit (SP-EF5201/SP-EF4601) for external speakers.
Note
Connecting multiple monitors
You can connect multiple monitors by using the 
RGB/COMPONENT input terminals (COMPUTER IN 1 
or COMPUTER IN 2) and the RGB/COMPONENT 
output terminals (MONITOR OUT).
• The length of the signal cables or surrounding environment 
may affect the image quality.
• When connecting multiple monitors, the screen may not 
display properly. In this case, turn off the power to all the 
monitors connected and then turn the power on again.
• For details, refer to the “SETUP MANUAL”.
Note