Eiki Efd 46 Owners Manual

							29
Menu operations
List of menu items
Picture
AV Mode  ......................................................Page 30
OPC  .............................................................Page 30
Backlight  ......................................................Page 30
Contrast  .......................................................Page 30
Brightness ....................................................Page 30
Color  ............................................................Page 30
Tint ...............................................................Page 30
Sharpness  ...................................................Page 30
Red ...............................................................Page 30
Green............................................................Page 30
Blue ..............................................................Page 30
Advanced
Color Temp. .......................................Page 31
DNR ...................................................Page 31
Film Mode ..........................................Page 31
Black ..................................................Page 31
3D-Y/C ...............................................Page 31
Monochrome  .....................................Page 31
Reset  ...........................................................Page 30
Audio
AV Mode  ......................................................Page 30
Treble  ..........................................................Page 32
Bass .............................................................Page 32
Balance ........................................................Page 32
Reset  ...........................................................Page 32
Power Management  ....................................Page 32
No Operation Off  .........................................Page 32
Ecology  ........................................................Page 33
Power Control
• Some menu items may not be displayed depending on 
the selected input source.
Note
Setup
Password ......................................................Page 33
Keylock
Main Set .............................................Page 34
Remote Control ..................................Page 34
Set Inputs .....................................................Page 34
Input Label ....................................................Page 35
Position
H-Position ...........................................Page 35
V-Position ...........................................Page 35
Reset ..................................................Page 35
Fine Sync
Resolution ..........................................Page 35
Signal Info ..........................................Page 35
Auto Sync ...........................................Page 35
H-Position ...........................................Page 36
V-Position ...........................................Page 36
Clock ..................................................Page 36
Phase .................................................Page 36
Reset ..................................................Page 36
Standby Mode ..............................................Page 36
Auto Restart ..................................................Page 36
RS-232C .......................................................Page 36
DHCP Client .................................................Page 36
TCP/IP ..........................................................Page 37
Status ...........................................................Page 37
All Reset .......................................................Page 37
Option
Closed Caption .............................................Page 38
Audio Output .................................................Page 38
Video System ...............................................Page 39
Signal Type
Computer1..........................................Page 39
Computer2..........................................Page 39
DVI .....................................................Page 39
HDMI ..................................................Page 39
Color Space ..................................................Page 39
Dynamic Range
DVI .....................................................Page 40
HDMI ..................................................Page 40
Language......................................................Page 40
HDMI Setup
Auto View ...........................................Page 40
Audio Select .......................................Page 40
Resize...........................................................Page 40
Timer
Clock ..................................................Page 40
Schedule ............................................Page 41
Sleep Timer ........................................Page 41
Picture Flip ....................................................Page 41
Multi Screen
Status .................................................Page 42
Position...............................................Page 42
H-Bezel...............................................Page 42
V-Bezel ...............................................Page 42
H-Position ...........................................Page 42
V-Position ...........................................Page 42
Reset ..................................................Page 42
Power On Delay ...........................................Page 42
LED...............................................................Page 42
Background ..................................................Page 42
 
						

							30
Picture menu
MENU[
Picture]
PictureAudio Power Control 
Contrast  OPC [Off]  AV Mode  [Standard]
Brightness 
Color
Tint
Sharpness 
Advanced 
Reset[  30] 
[    0] 
[    0] 
[    0] 
[    0] 
Red  [    0] 
Green  [    0] 
Blue  [    0] 
Backlight [+16] 
+
+
+ +
+
+
+
„ Selecting a preset AV Mode
The AV Mode function enables you to select 
appropriate settings for picture and audio to account 
for the system environment which can vary due to 
factors like room brightness or the type of image 
input from external equipment.
Selectable 
itemsDescription
Standard For standard image
PresentationBrightens portions of image for 
more enhanced presentations.
Movie Gives natural tint to the image.
Game Gives sharpness to the image.
*sRGBFor high fi delity reproduction of 
images from a computer.
•  You can set or adjust each item in the “Picture” 
menu to your preference. Any changes you make 
are retained in memory.
• You can also press AV MODE
 on the remote control to 
select the AV Mode. (See page 26
.)
• *sRGB is an international standard of color reproduction 
regulated by the IEC (International Electrotechnical 
Commission). As the fi xed color area has been decided 
by the IEC, the images are displayed in a natural tint 
based on an original image, when “sRGB” is selected. 
You cannot set the items, “Red”, “Green”, “Blue”, “Color 
Temp.”, when “sRGB” is selected.
• When “sRGB” is selected, the image may become dark, 
but this does not indicate a malfunction.
Note
„ Picture adjustment
You can adjust the picture to your preference.
• “Backlight” cannot be adjusted when “OPC” is set to “On” 
or “On(Display)”.
Note
Selectable
items
{
button 
y
button
OPC Sets whether or not the screen 
brightness is automatically adjusted 
according to the lighting condition in 
the room. (OPC setting: See page 31.)
Backlight The screen dims The screen 
brightens
Contrast For less contrast For more contrast
Brightness For less 
brightnessFor more 
brightness
Color For less color 
intensityFor more color 
intensity
Tint Skin tones 
become purplishSkin tones 
become greenish
Sharpness For less 
sharpnessFor more 
sharpness
Red
*1For weaker red For stronger red
Green*1For weaker green For stronger 
green
Blue
*1For weaker blue For stronger blue
Advanced*2For finer picture adjustments. (See 
page31.)
Reset Resets all picture adjustment items to 
the factory preset values.
*1 Not adjustable/selectable when selecting “sRGB”.
*2 “Color Temp.” is not adjustable/selectable when 
selecting “sRGB”.
Menu operations
 
						

							31
OPC (Optical Picture Control) setting
You can set the monitor to automatically adjust the 
screen to suitable backlight brightness according to 
the lighting conditions.
OPC indicator
Selectable
itemsDescription
On(Display) Displays the OPC effect on 
the screen while adjusting the 
brightness of the screen.
On Automatically adjusts
Off The brightness is fixed at the value 
set in “Backlight”. (See page 30.)
OPC indicator
Light off “Off ” is selected in the OPC 
setting.
Lighted (Green) “On” or “On(Display)” is selected 
in the OPC setting.
• Make sure no object obstructs the OPC sensor, which 
could affect its ability to sense surrounding light.
Note
„ Advanced picture settings
The advanced settings enable you to set the picture
adjustment in more detail. There are 6 options you 
can choose from.
Color Temp.  (Color Temperature)
Adjusts the color temperature to give the best white 
image.
Selectable
itemsDescription
High White with bluish tone
Mid-High
Middle
Mid-Low
Low White with reddish toneDNR (Digital Noise Reduction)
Reduces noise on the screen and produces a 
clearer video image.
Film Mode
Automatically detects a film-based source (originally 
encoded at 24/25 frames/second, depending on the 
vertical frequency), analyses it then recreates each 
still film frame for high-definition picture quality.
• This model is not compatible to 1080/24P input signal.
Note
Black
For easier viewing, change the viewing depth by 
selecting a level for automatically adjusting the dark 
portion of an image.
Selectable
itemsDescription
On For high detail in black portions
Off No adjustment
3D-Y/C
Provides high quality images with minimal dot crawl 
and cross color noise.
Selectable
itemsDescription
Standard Normal adjustment
Fast For movie image
Slow For still image
Off 3D-Y/C off
• 3D-Y/C is not selectable depending on the input signal 
type.
• 3D-Y/C may not operate depending on the input signal 
type or noisy input signal.
Note
Monochrome
For viewing images in monochrome.
Menu operations
 
						

							32
Audio menu
Audio 
Treble 
Bass
Balance
Reset[  0] 
[  0] -
L+
[  0]  - +
R
StandardPower Control 
„ Audio adjustment
You can adjust the audio of the selected AV mode.
Selectable
items
{
button 
y
button
Treble For weaker treble For stronger treble
Bass For weaker bass For stronger bass
Balance Decrease audio 
from the right 
speakerDecrease audio 
from the left 
speaker
• For resetting all adjustment items to the factory preset 
values, press 
x
/
z
 to select “Reset”, press ENTER
,
press 
x
/
z
 to select “Yes”, and then press ENTER
.
Note
Power Control menu
Power Control
No Operation Off Power Management
Ecology
„ Power Management
You can set the monitor to automatically power off 
when there is no image displayed on the computer.
SelectableitemsDescription
Off • No power management 
•  Factory preset value.
Mode1 •  If no signal inputs for approximately 
8 minutes, the power shuts down.  
•  Even if you start using the computer 
and the signal inputs again, the 
monitor stays off.   
•  The monitor turns on again by 
pressingON on the remote control. 
Mode2 •  If no signal inputs for approximately 
8 seconds, the power shuts down.   
•  When you start using the computer 
and the signal inputs again, the 
monitor turns on.   
• If you turn off the power by disconnecting the power cord 
when setting “Mode2” in power management, the monitor 
may not function properly after turning the power on 
again. In such case, press ON
 on the remote control.
• Pressing POWER
 on the monitor will have the same 
result.
• When “Mode2” is set in “Power Management”, you 
cannot set “Standby Mode” to “Mode3”. (See page 36
.)
Note
„Auto power-off when there are no 
operations performed
(No Operation Off)
You can set the monitor to automatically power off 
when no operation is performed for more than 30 
minutes or 3 hours.
• “Disable” is the factory preset value.
Note
Menu operations
 
						

							33
„Ecology
When set to “Yes”, The monitor activates the 
following power saving mode.
•  “OPC” set to “On” (Page 31)
•  “Standby Mode” set to “Mode2” (Page 36)
•  “No Operation Off ” set to “3 Hours” (Page 32)
•  “Power Management” set to “Mode1” (Page 32)
• When selecting “Yes” for “Ecology”, the settings related to 
“Ecology” (“OPC”, “Standby Mode”, “No Operation Off”, 
and “Power Management”) will be lost. Once you have 
selected “Yes” for “Ecology”, these settings will not return 
to the previous setting by selecting “No”. To restore these 
settings, each setting must be changed individually.
Note
Setup menu
SetupOption
Set Inputs
Input Label
Position Password
Keylock
Fine Sync
DHCP Client RS-232C
TCP/IP
Status
All Reset Auto Restart Standby Mode
„Setting a password
(Password)
If you do not want others to change the setting
for the “Setup” menu, set a password.
1  Select “Password”, then press ENTER.
•  The screen for entering the password appears.
Enter your new password.
Use 4 digits.
Old Password
----
----
---
MENU [Setup---Password]
New Password
Reconfirm
2 Press 
x
/
z
 to set the fi rst digit in “New 
Password”, then press 
y
.
3  Enter the remaining 3 digits, then press ENTER.
•  To return to the previous digit, press 
{.
4  Enter the same password in “Reconfi rm”, then 
pressENTER.
•  The status for “Password” changes to 
“
 (enable)”.
• Once the password is set, you must enter the password 
to change the “Setup” menu settings.
Note
Menu operations
 
						

							34
Changing the password
1  Select “Password”, then press ENTER.
•  The screen for entering the password appears.
2  Enter the password in “Old Password” using 

x
/
z
/
{
/
y
, then press ENTER.
3  Enter the password in “New Password” using 

x
/
z
/
{
/
y
, then press ENTER.
4  Enter the same password again in “Reconfi rm” 
using
x
/
z
/
{
/
y
, then press ENTER.
• If you do not need the password protection for the “Setup” 
menu settings anymore, press ENTER
 without entering 
new password in steps 3 and 4.
• To cancel the password settings, press RETURN
.
Note
If you forget the password
If you forget the password, perform the following 
procedure to delete it, then set a new password.
On the remote control or the monitor, press

{
:
ENTER
:
y
:
ENTER
:
{
:
ENTER

:
MENU.
„Keylock
You can disable operations on the monitor and the 
remote control that use buttons.
Selectable Items Description
Main Set Off Enables operation.
Level1 Only the POWER button on the 
monitor is available.
Level2 All of the operation buttons on 
the monitor are unavailable.
Remote
ControlOff Enables operation.
Level1 Only the ON/STANDBY buttons 
on the remote control are 
available.
Level2 All of the operation buttons 
on the remote control are 
unavailable.
When you cannot unlock the operation buttons using the 
menu, for example, when all of the operation buttons on the 
monitor and the remote control are locked simultaneously, 
follow the steps below.
• To unlock all of the buttons on the monitor and the remote 
control:
Press and hold ENTER
 (monitor/remote control) for 5 
seconds when no on-screen displays are displayed.
If the password is set, the screen for entering the 
password appears. Enter the password using 
x
/
z
/
{
/
y
(monitor/remote control).
• To unlock the buttons on the monitor:
1) Press and hold POWER
 on the monitor for 5 seconds 
to turn off the main power.
2) Press and hold POWER
 on the monitor for 5 seconds 
to unlock the monitor buttons.
Note
„Bypassing unused input selections
(Set Inputs)
This function allows you to skip the input mode that 
you rarely use. You can skip the input modes when 
pressingINPUT on the monitor.
Selectable items Description
Computer1
Computer2
DV I
HDMI
S-VIDEO
VIDEOOnSets the input mode as 
“selectable”, respectively.
OffSets the input mode as 
“unavailable”, respectively.
Menu operations
 
						

							35
„Labelling input sources
(Input Label)
You can assign each input source a label as you 
prefer.
1 Press COMPUTER (1/2), DVI, HDMI, S-VIDEO or 
VIDEO to select the desired input source.
2 Press MENU and the MENU screen appears.
3 Press 
{
/
y
 to select “Setup”.
4 Press 
x
/
z
 to select “Input Label”, and then 
pressENTER.
•  When an HDMI input terminal is selected, a 
Menu screen for selecting “Auto” or “Manual” is 
displayed.
•  When you select “Auto” using 
x
/
z
, the Menu 
screen returns to the previous screen.
•  When you select “Manual” using 
x
/
z
, the 
screen for labelling the input source appears. 
Proceed to step 5.
5 Press 
x
/
z
 to select characters and 
{
/
y
 to 
move to the desired digit to label the input source.
•  When you want to change the input label 
that you have already assigned to the default 
name, press 
{
/
y
 to move to “CLEAR” on the 
“Input Label” screen, and then press ENTER.
6  Repeat the above until the name is fully spelled 
out, and then press MENU.
•  The name can be 9 characters or less.
• When you want to set an input source name 
of less than 9 characters, press MENU to exit 
from the labelling menu.
„Adjusting the image position
(Position)
For adjusting a picture’s horizontal and vertical 
position.
Selectable 
ItemsDescription
H-Position Centers the image by moving it to 
the left or right.
V-Position Centers the image by moving it up 
or down.
• For resetting all adjustment items to the factory preset 
values, press 
x
/
z
 to select “Reset”, press ENTER
,
press 
x
/
z
 to select “Yes”, and then press ENTER
.
• Adjustments are stored separately according to input 
source.
• Images may not be displayed properly depending on the 
settings and/or signals.
Note
„Adjusting the computer image
(Fine Sync)
Resolution
Ordinarily, the type of input signal is detected 
and the correct resolution mode is automatically 
selected. However, for some signals, the optimal 
resolution mode on the “Resolution” menu may need 
to be selected to match the computer display mode.
Signal Info
Displays infomation about the input signal, such 
as resolution, horizontal frequency, and vertical 
frequency.
Auto Sync Adjustment (Auto Sync)
Selectable 
itemsDescription
Yes Perform Auto Sync adjustment.
No Do not perform Auto Sync adjustment.
• Auto Sync adjustment is also performed by pressing 
AUTO SYNC
 on the remote control.
• The Auto Sync adjustment may take some time to 
complete, depending on the image of the computer 
connected to the monitor.
• When the optimum image cannot be achieved with Auto 
Sync adjustment, use manual adjustments. (See page 
36
.)
Note
Menu operations
 
						

							36
Adjusting the computer image manually
Ordinarily you can easily adjust the picture as 
necessary to change image position using “Auto 
Sync”. In some cases, however, manual adjustment 
is needed to optimize the image.
Selectable 
itemsDescription
H-Position Centers the image by moving it to the 
left or right.
V-Position Centers the image by moving it up or 
down.
Clock Adjusts when the image flickers with 
vertical stripes.
Phase Adjusts when characters have low 
contrast or when the image flickers.
• If “H-Position” and “V-Position” in “Fine Sync” are set, 
“H-Position” and “V-Position” in “Position” become invalid.
• For resetting all adjustment items to the factory preset 
values, press 
x
/
z
 to select “Reset”, press ENTER
,
press 
x
/
z
 to select “Yes”, and then press ENTER
.
• Images may not be displayed properly depending on the 
settings and/or input signals.
Note
„Reducing the start-up time
(Standby Mode)
You can reduce the monitor’s start-up time after 
turning on the power with the remote control.
Selectable 
itemsDescription
Mode1 Starting the monitor is quick from 
standby.
Mode2 The RS-232C and Network functions 
are activated even if the monitor is in 
the standby mode.
Mode3 Power consumption is low while in  
standby mode. 
The RS-232C and Network functions 
are switched off in standby mode.
• When “Mode3” is set in “Standby Mode”, you cannot set 
“Power Management” to “Mode2”. (See page 32
.)
Note
„Auto restart function
(Auto Restart)
Selectable 
itemsDescription
On If the power cord is unplugged from 
the outlet or the breaker switch is 
turned off when the monitor is on, 
then the monitor automatically turns 
on when the power cord is plugged 
into the AC outlet or the breaker 
switch is turned on.
Off The monitor does not turn on 
automatically when the power cord 
is plugged into the AC outlet or the 
breaker switch is turned on.
„Selecting the transmission speed 
(RS-232C)
Make sure that both the monitor and computer are 
set for the same baud rate.
Selectable 
itemsDescription
9600bps Transmission speed is slow.
115200bps Transmission speed is rapid.
„DHCP client setting
(DHCP Client)
Connect the LAN cable before turning the monitor 
on. If not, the DHCP Client function does not work.
Selectable 
itemsDescription
On Obtains confi guration parameters for 
TCP/IP network automatically.
Off Sets the TCP/IP manually.
Select “On” for “DHCP Client”. “Obtaining IP 
Address...” appears, then the menu screen appears. 
Confi rm the parameters of IP Address, Subnet Mask 
and Gateway on the TCP/IP screen.
If the DHCP server is not available, “Could not 
obtain IP Address.” appears.
In this case, set the TCP/IP manually. (See page 
37.)
Menu operations
 
						

							37
„TCP/IP setting
(TCP/IP)
Set the TCP/IP manually.
1  Select “Off ” for “DHCP Client”, then press 
ENTER.
2 Select “TCP/IP”, then press ENTER.
3 Enter “IP Address” using 
x
/
z
/
{
/
y
, then press 
ENTER.
IP Address
Subnet Mask
Gateway192.168.150.002
255.255.255.000
000.000.000.000 MENU [Setup---TCP/IP]
4 Enter “Subnet Mask” using 
x
/
z
/
{
/
y
, then 
pressENTER.
5 Enter “Gateway” using 
x
/
z
/
{
/
y
, then press 
ENTER.
Selectable 
itemsDescription
IP Address Factory default setting: 
192.168.150.002
Enter an IP address appropriate for 
the network.
Subnet
MaskFactory default setting: 
255.255.255.000
Set the subnet mask to the same as 
that of the computer and equipment 
on the network.
Gateway Factory default setting: 
000.000.000.000
* When not in use, set to 
“000.000.000.000”.
• Confi rm the existing network’s segment (IP address 
group) to avoid setting an IP address that duplicates the 
IP addresses of other network equipment or computers. 
If “192.168.150.002” is not used in a network with an IP 
address of “192.168.150.XXX”, you don’t have to change 
the monitor IP address.
• For details about each setting, consult your network 
administrator.
Note
„Confi rming the monitor information 
(Status)
You can confi rm the following information.
• DHCP Client
• IP Address
• Subnet Mask
• Gateway
• MAC Address
• Monitor Name
• Serial Number
• For information on how to change the monitor name, see 
“SETUP MANUAL” contained in the supplied CD-ROM.
Note
„Returning to the default settings 
(All Reset)
This function allows you to initialize the settings you 
have made in the monitor.
1 Press 
x
/
z
 to select “All Reset” and press 
ENTER.
2 Press 
x
/
z
 to select “Yes” and press ENTER.
The following items or menu cannot be initialized.
• “Setup” menu 
Resolution
• “Option” menu 
Language
Note
Menu operations
 
						

							38
Option menu
Option
Dynamic Range 
Language
HDMI Setup
Resize
Timer
Picture Flip
Multi Screen
Power On Delay
LED
Background
Color Space  Signal Type  Audio Output 
Video System  Closed Caption
„Selecting Closed Caption
(Closed Caption)
This monitor is equipped with an internal Closed 
Caption decoder. It allows you to view conversations, 
narration and sound effects as subtitles on your 
monitor. Closed Captions are available on some TV 
programs and on some VHS home video tapes at 
the discretion of the program provider. 
•4 kinds of closed caption service (CC1, CC2, Text1, Text2) 
are potentially available, but a broadcast may contain 
none or only some of these services at the discretion of the 
program provider.
•While displaying on-screen displays, Closed Caption 
information disappears.
Note
„Setting the audio output type
(Audio Output)
This function determines whether the audio level 
output from the audio output terminal is fi xed or 
variable by linking with VOLUME.
Selectable 
itemsDescription
FAO
(Fixed Audio 
Output)Audio output that does not vary in 
strength with the volume level of 
the source monitor.
VAO
(Variable 
Audio Output)Audio output that varies in strength 
with the volume level of the source 
monitor.
• When “Audio Output” is set to “VAO”, sound via speakers 
is muted.
• When “Audio Output” has been set to “VAO”, fi rst make 
sure to lower the volume of the monitor before turning the 
power on or off and when switching the input.
• When the monitor is connected to audio equipment:
-- It is recommended that “FAO” be selected on “Audio 
Output”. Because the audio signal from the audio 
equipment does not vary in strength with the volume 
level of the monitor, you can enjoy better sound.
-- When “FAO” is selected on “Audio Output”, video and 
audio may not synchronize.
-  When connecting audio equipment that has a function 
for adjusting audio delay time, adjust the delay time 
for synchronizing video and audio.
-  When the audio equipment does not have such a 
function and the unsynchronized video and audio 
bothers you, select “VAO” on “Audio Output”. 
Selecting “VAO” synchronizes video and audio 
automatically.
Note
Menu operations