Dwin Electronics Transvision 3 Enhanced Users Manual

29

2D. Connecting the TransVision™ 3E System
Connect the AC Power Cord to the projector and connect it to an unswitched 
AC outlet. Connect the projector to the TransVision
™ 3E Processor using the 
circular connector of the DVI cable.
 A. The AC power receptacle should be connected to a non-switched 120 VAC 
outlet using the power cord provided with the TransVision
™ 3E system.
 B. The IR Sensor points toward the screen so that IR commands sent by the 
remote control are received by the system. To...

30

(3) FINAL ADJUSTMENTS
After the physical mounting is complete, horizontal and vertical adjustments 
can be made to center and align the projected image to the screen. 
Before making these adjustments you should:
1. Turn the system On. 
2.  Adjust the zoom and focus. Use the On-Screen Menus to help refine focus.
3.  Once on screen menus can be clearly viewed, go to Screen Setup menu.
4.  Make the following horizontal and vertical adjustments to align the white  field pattern to the screen. 
•  To move...

31

Physical Dimensions — TransVision™ 3E
13.5”4.5”
4.5”
14 ”
2.0”
5.0”
A
A
AA
“A” CEILING MOUNT HOLE LOCATION
5.2”
AC Input &
Circular Connector 

32

TransVision™ 3E RS-232 Control
The RS-232 interface for the TransVision™ 3E System can be operated from any 
terminal, such as a Windows based PC running HyperTerminal.
Communication Port Set-Up  Connector pin-out
Baud Rate:  9600   3  TX (Transmit Data)
Parity:   none  2  RX (Receive Data)
Stop bits:   1  5  GND (Signal Ground)
Num. of bits:  8 bits
Flow control:   none
Each command is enclosed in the 
[ ] character envelope.
Note: Sequential commands must be separated with proper delays.
Any...

33

 Projector Specifications
Display Device 1280 x 720 DarkChip™ 3  
Aspect Ratio  16:9, 4:3, Letterbox
Native Resolution
  1280 x 720/ 16:9
Number of Pixels  921,600
Screen Configuration  Front or Rear throw
Mounting  Floor or Ceiling
Zoom Range  1.45:1
Image Size  60 to 200 inch Diagonal
Throw Distance  1.41 to 2.1 times Screen Width
Projection Offset  Lens Level to 40% of Picture Height
Light Source  200 Watt VIP Lamp
Lamp Life  2000 Hours 
Contrast 3000:1
INPUTS
 DVI Proprietary Digital
 AC Power  3...

34

Digital Video Processor Specifications
Video Systems  HDTV / DTV / NTSC / PAL 
Scanning Formats   480i, 480p, 540p, 580i, 580p, 720p, 1080i
PC Signals  VGA / SVGA / XGA / SXGA
INPUTS
 DVI  2 x DVI-D with HDCP
 Component  2 x RCA, Y: 1 Vp-p / 75 ohm 
    Pb Pr: 0.7 Vp-p / 75 ohm
   S-Video  2 x 4 pin Mini-Din                       
    Y: 1 Vp-p / 75 ohm
     C: 0.286 Vp-p / 75 ohm
  
Composite  2 x RCA: 1 Vp-p / 75 ohm
  
RGB/PC  2 x HD-15 Pin
  RS-232 Serial  1x D-9 Pin, RS-232 Compatible
 AC Power...

35

Limited Warranty 
This warranty applies only to the first person or entity that purchases the Trans-
Vision
™ 3E for personal or business use and not for the purpose of distribution 
or resale. The warranty period is for one (1) year from the date of purchase for 
labor and parts.  DWIN Electronics shall not be liable or in any way responsible for any inci
-
dental or consequential damages of any kind. This warranty covers all defects 
in material and workmanship when shipped in its original...

36

operate in sequence with parameters loaded into memory. The unstable 
pixel appears to be flickering asynchronously with the image.
Acceptable Criteria:
•  Dark Pixel – No more then 4 dark pixels.
•  Bright Pixel – No bright pixels.
•  Unstable Pixel – No unstable pixels.
DWIN Electronics will, at its option, either repair or replace the defect, or 
replace the defective product or part thereof at no charge to the owner for parts 
and labor covered by this warranty. If a unit is examined which is not...

37

•  damage from the performance of repairs by someone not authorized by DWIN Electronics;
•  any  unit  on  which  the  serial  number  has  been  effaced,  modified,  or 
 
removed;
•  any failed lamp with a serial number that does not match the serial number  associated with the projector
•  any failed replacement lamp with a serial number that does not match the  serial number of the replacement lamp. 
•  damage occurring during shipment;
•  units  which  have  been  altered  or  modified  in...