Dwin Electronics Transvision 3 Enhanced Users Manual

9

3. SWITCHED +12 VDC OUTPUTS
The TransVision
™ 3E Processor has two switched +12 VDC outlets (2.5 mm DC 
plug) labeled as RY1 and RY2. These outlets may be used to trigger a relay in 
an electric device. Each output provides 100 ma DC current. See Relay Setup 
menu for more details.
4. RGB INPUTS
The RGBS1 and RGBS2 inputs (D-sub 15) are provided for High-Definition (480p, 
580p, 720p, 1080i) sources and computer graphics with VGA, SVGA, XGA, and 
WXGA resolution. For computer graphics with VGA, SVGA,...

10

7. COMPOSITE VIDEO INPUTS (V1, V2)
The V1 and V2 inputs are provided for NTSC (480i) or PAL (580i) video sources, 
such as off-air tuners, satellite systems, cable boxes, VCR and DVD players.  
8. COMPONENT VIDEO INPUTS (Y1, Y2, Y3)
Two component video Y, Cr, Cb or Y, Pr, Pb inputs are provided for interlaced 
video signals from regular DVD players (480i, 580i), progressive component 
video signals from progressive DVD players (480p, 580p), and progressive or 
interlaced HD signals (480p, 540p,...

11

Programming URC-100 Remote Control  
to Operate the TransVision
™ 3E Processor
The TransVision™ 3E System is shipped with a factory pre-programmed remote  
control.
1. 
Press the TV  device button. 
2.  Press and hold both the  SHIFT and ENTER  buttons for 3 seconds. The display 
will blink “Set” and then “DWIN.”
3. Enter the TransVision
™ 3E brand code: 177
4. Press the  LIGHT button on the right hand side to complete the programming.
 
To  operate  other  audio  and  video  devices  refer  to  the...

12

1 23
4 5
6
7 8
9
+1 0 0
ENT
MODESUBCTRREAR
=
SELECT
AUD C
DDVD
AUX
SA
T
MUTE
MENUEXIT
GUIDE INFO
PREV
CH
TV
VC
R
OFF TV
VC
R
SHIFT
CBLLIGHT
DWIN
ON
VOL C
H

Quick Reference Remote Control Operation  

13

The remote control provided with the TransVision™ 3E is a universal remote 
control capable of controlling 8 different devices. 
1. Select 
TV device to control the TransVision™ 3E System.
2. Press 
ON to turn the TransVision™ 3E ON. 
3. Press 
OFF to turn the TransVision™ 3E OFF.
4.  Press 
MENU  to display the Main menu or to return to the previous menu.
5.  Use the numbered buttons for direct switching of inputs. 
  To select a specific input, press a numbered button.  
6. Press up
 ▲ or down ▼ to...

14

Navigating the Control Menus
Information Menu
The Information menu reports the current status for input video source and 
lamp hours used. The  Information menu may be accessed when no other menu 
is displayed on the screen.
1.  To display the  Information Menu , press INFO button on the remote control.
2. Press 
EXIT on the remote to clear the screen immediately. 
Main Menu
The  Main  menu  offers  a  choice  of  Input selection  or   Format  selection,  and 
navigation options to  Video controls...

15

Input Option
All 10 video inputs may be selected either directly or through 
Input menu. To 
select a video input directly, press the numeric buttons on the remote control 
that corresponds to the desired input:
   • For composite video inputs, press 
1 or 2
  • For S-Video inputs, press 
3 or 4
  • For component video inputs, press 
5 or 6
  • For RGB inputs, press 
7 or 8
  • For DVI inputs, press 
9 or 0
To select a video input through the menu:
1.  From  the  Main  menu  scroll  up
 ▲  or down ▼...

16

1.  From the Main menu scroll  up ▲ or down ▼ to highlight the  Format option. 
This enables to select the aspect ratio.
2.  Use the  left
 ◀ or right ▶ buttons to sequentially select the aspect ratio. 
3.  Or use buttons  1-4 on the remote control for direct selection of Formats. 
4.  To change formats without entering the  Main menu, Press the  GUIDE button. 
To access the format option directly (bypassing the 
Main menu), press the 
GUIDE button followed by the corresponding number buttons:  1,...

17

6. To restore the full Video menu , press MENU, up ▲ or down ▼ buttons. 
Picture setting changes made with the  Video menu are saved in memory for 
each of the ten video inputs.  Many video sources are different enough to re
-
quire this fine-adjusting and these settings will be recalled each time a video 
input is selected.
Setup Options
1.  From the Main menu scroll up ▲ or down ▼ to highlight the Setup option. 
2.  Use the  left
 ◀, right ▶ or  SEL  buttons to advance to the  Setup Options menu....

18

Rename Input
Video 1 Video 1
2. After adjusting to a desired menu position, press MENU button on the remote 
to go back to the 
Setup menu or press EXIT button to clear the screen.
 
Rename Inputs 
This  feature  allows  you  to  change  the  names  of  all  ten  video  input  sources 
which appear on the 
Main menu. A default name is provided for each input 
such as  Video 1.  
1. Scroll 
up ▲ or down ▼ the default list to highlight a desired input. 
2.  Scroll the 
right ▶ cursor key to the first...