DuVoice Mitel SX50 COV Instructions

							  07/27/00  
 Integration Notes-Switch #534  
 
Mitel SX50 COV 
 
Introduction  
This file gives basic information on integrating the Duvoice VM with Mitel SX50 
telephone system.  Refer to the Mitel programming for more information. 
           
Switch Hardware Required 
·  Mitel SX50 telephone system with MS55 software.        
·  One extension on a COV/Superset 4 card per Duvoice VM port is required.   
·  One analog extension for the modem is recommended.  If no extensions are 
available wire a 
         trunk line to the modem using a TKM switch. 
 
Switch Programming 
 
Command 100  System Options 
     REG 03(Tone And Ringing Control) = 0301411000 BIT h=0 Disconnect Tone:Disable 
     REG 12(Message Waiting) = 121030 BIT c=1,BIT d=0, BIT f=0 
 
Command 110 Feature Access Code Programming 
     REG19(Hunt Group 1 Access Code) = 19491  Hunt Group Access Code =491 
 
COS Programming:  Create COS 9 For VM 
Command 129 COS 9 Programming 
     REG 2 21100010001 
  BIT a(Register)=2(Register 2) 
  BIT b(Switchhook/Ground Button Flash=1(Flash for Consultation Hold) 
  BIT c(Call Direction)=1(Bothway Calling) 
  BIT g(Message Waiting)=1(Enabled) 
  BIT k(Do Not Disturb)=1 
     REG 3 30011000001 
  BIT a(Register)=3(Register 3) 
  BIT d(Data Line Security)=1(Enabled) 
  BIT e(Call Hold)=1(Enabled) 
  BIT k(Voice Mail Port)=2(Message Optimization Control) 
     REG 4 4111100100 
  BIT a(Register)=4(Register 4) 
  BIT b(Call Forward-Follow Me)=1(Internal Only) 
  BIT c(Call Forward-Busy)=1(Internal Only) 
  BIT d(Call Forward-No Answer)=1(Internal Only) 
  BIT e(Call Forward Busy/No Answer)=1(Internal Only) 
  BIT h(Executive Busy Override Security)=1(Enabled) 
     REG 5 50000000000 
  BIT a(Register)=5(Register 5)  
						

							  07/27/00    BIT b-j(Abbreviated Dial Numbers)=0(Disabled) 
 
Switch Programming Continued… 
 
 
 
     REG 7 71010100 
  BIT a(Register)=7(Register 7) 
  BIT b(Superset4/420 Telephone message Programming)=1(Enabled) 
  BIT d(Auxiliary Attendant Position)=1(Enabled) 
  BIT f(Directed Call Pickup Security)=1(Enabled) 
     REG 8 80000 
  BIT a(Register)=8(Register 8) 
  BIT b(Extension Camp-on)=0(Disabled) 
  BIT c(Trunk Camp-on)=0(Disabled) 
  BIT d(Inward Dial Trunk Camp-on)=0(Disabled) 
 
Superset/Station Programming:   Example Slot 4 Programming 
 Command 304 
  01090000301 
  02090000302 
  03090000303 
  04090000304 
  05090000305 
  06090000306 
  07090000307 
  08090000308 
  BIT a and b(Circuit Number 01-08 for COV and DNIC Cards) 
  BIT c(Extension Type)=0(Extension) 
  BIT d(Class Of Service) 
  BIT e(Allow Attendant to Change Extension COS)=0(Not Allowed) 
  BIT f(Pickup Group)=0(No Pickup Group) 
  BIT g(ARS Routing Class of Service)=0(ARS Route does not apply) 
  BIT h(OPS Loop Length)=0(Short) 
  BIT i,j,k, and l(Extension Number) 
 
 Command 361 Hunt Group Programming 
  REG 1     100 
     BIT a(Register)=1(Register 1) 
     BIT b(Hunt Type)=0(Circular) 
     BIT c(Hunt Group Linking)=0(Unlinked) 
  REG 2-9 2301 
                  3302 
     4303 
     5304 
     BIT a(Hunt Group Member Number) 
     BIT b,c,d and e(Hunt Group Member Extension Number) 
 
Message Waiting Port Should Be In The Hunt Group 
  
						

							  07/27/00  Command 425-4     Station Programming MWI Lines 
     REG 1: Extensions 301-304 
     01111301 
     01111302 
     01111303 
     01111304 
 
Switch Programming Continued… 
 
 
Command 501 Trunk Programming (Auto Attendant Day And Night) 
     REG 4 40501610000 Hunt Group 161 
  BIT a(Register)=4(Register 4) 
  BIT b(Dictation Trunk)=0(Disabled) 
  BIT c(Inter-ringing Delay)=5(5seconds) 
  BIT d(Day Answer Mode)=0(Direct-In-Line) 
  BIT e,f, and g(Day Answer Point)=161(Hunt Group 161) 
  BIT h(Busy Intercept)=0(Disabled) 
  BIT i(Do Not Disturb Intercept)=0(Disabled) 
  BIT j(No Answer Intercept)=0(Disabled) 
  BIT k(Illegal/Vacant Number Intercept)=0(Disabled) 
 
     REG 5 501610000 Hunt Group 161 
  BIT a(Register)=5(Register 5) 
  BIT b(Night Answer Mode)=0(Flexible Night Service) 
  BIT c,d, and e(Night Answer Point)=161(Hunt Group Number) 
  BIT f(DID Night Answer Point)=0(Disabled) 
 
Call Forward Busy/No Answer Code 60 Command 110.  Program Call Froward Busy/No 
Answer Into Room COS.   Program Each Room To Call Forward To VM Hunt Group 
491(60 491).  Call Forward VM Ports For No Answer To Operator Extension. 
 
VM Programming 
 
Program VM With Switch Integration 534.