Dukane Projector 6430 User Manual

24
English ...
Introduction
Viewing 3D Images
The projector provides 3D images to a user wearing commercially 
available LCD shutter eyeglasses.
CAUTION
Health precautions
Before viewing, be sure to read health care precautions that may be found 
in the user’s manual included with your LCD shutter eyeglasses or your 3D 
compatible content such as DVDs, video games, computer’s video files and 
the like.
To avoid any adverse symptoms, heed the following:
- Do not use LCD shutter eyeglasses for viewing any...

25... English
Installation
Connecting the Projector
	Make sure that the 
power plug is fully 
inserted into both the 
projector AC IN termi-
nal and the wall outlet. 
	 The MONITOR 
OUT connector supports 
Separate sync signal 
only.
Connect to Computer/Notebook
1. ........................................................................\
.................... Power cord (supplied)
2. ........................................................................\
...................................... HDMI...

26
English ...
Installation
1. ........................................................................\
.................... Power cord (supplied)
2. ........................................................................\
...................................... HDMI cable
3. ....................................................................... Computer cable (VGA) (supplied)
4. ........................................................................\
....................................... RS232...

27... English
Installation
	Due to the 
difference in 
applications for each 
country, some regions 
may have different 
accessories.
	 When Deep Color 
is set to ON on your 
HDMI equipment, 
video or audio noise 
may be generated 
depending on the 
equipment or cable 
being used. Should 
this happen, set Deep 
Color to OFF (8 bit). 
Connect to Video Sources
	Make sure that the 
power plug is fully 
inserted into both the 
projector AC IN termi-
nal and the wall outlet.
1....

28
English ...
Installation
1. ........................................................................\
.................... Power cord (supplied) 
2. ........................................................................\
.................................... HDMI cable*
3. ................................................... 15-Pin to 3 RCA Component/HDTV Adaptor
4. ........................................................................\
................................................ Audio
5....

29... English
Installation
Powering On/Off the Projector
Turn on the projector 
first and then the signal 
sources.
(*)When “Normal” is 
selected for “Standby 
Mode”, the Power LED 
indicator will turn 
red; when “Network 
standby” is selected for 
“Standby Mode”, the 
Power LED indicator 
will turn orange.
POWER/STANDBY 1
	
When you first 
turn on the projec-
tor, you will get the 
Startup menu. This 
menu gives you the 
opportunity to select 
the menu languages. 
To select the language, 
use the 
,...

30
English ...
Installation
Powering Off the Projector
1.     Press the “POWER OFF” button on the remote control or the 
 button on the control panel to turn off the projector lamp, 
you will see a message as below on the on-screen display.
 
ARE YOU SURE
YES NO
POWER OFF
2.   Press the “POWER OFF” button again to confirm. 
3.   
Disconnect the power cord from the electrical outlet and the 
projector. If you disconnect the power cord while viewing 
the picture and connect the power cord again, wait for...

31... English
Installation
Warning Indicator
   When the “STATUS” LED indicator flashes red, it 
indicates the projector has overheated. The projector will  
automatically shut itself down.
WARNING! TEMPERATURE TOO HIGH
1. MAKE SURE AIR IN AND OUTLETS ARE NOT BLOCKED.
2. MAKE SURE THE ENVIRONMENT TEMPERATURE IS UNDER 40 DEGREE C
    When the “LAMP” LED indicator turns red and the message 
below displays on-screen, the projector has detected that 
the lamp is approaching its end of life. When you see...

32
English ...
Installation
Adjusting the Projected Image
Adjusting the Height of Projection Image
The projector is equipped with the tilt foot for adjusting the 
image height.
1.   Press the tilt foot release button. 1
    Keep to press the tilt foot release button for raising or 
lowering the projector, then lock the button by releasing it. 
2
2.   Rotate the rear feet counter clockwise to raise the projector 
or clockwise to lower it. 3
Rear footRear foot
Tilt foot
release button
Tilt Foot32
1
3
Two...

33... English
Installation
Adjusting the Projector’s Focus
To focus the image, rotate the focus ring until the image is clear. 
To zoom the image, turn the zoom lever in or out.
Focus Ring
Zoom Lever