Dukane Imagepro 9017 D-ila Multimedia Projector Users Manual

							51 
 About warning indicators
If something abnormal has occurred in the projector, the warning mode sets in and the type of abnormality will be indicated by a
combination of indicators displayed on the control panel as shown in the following table.
The projector will then automatically stop projection and run the cooling fan for about 90 seconds.
Warning Indication

 Action to be taken upon warning indications
Please follow the procedures below.
For No.1-3
No.1 : Unplug from the main power outlet and restart according to the basic operation procedures.
No.2 : After checking if a shock (such as from knocking) has not ocurred during operation, unplug from the main power outlet
and restart according to the basic operation procedures.
No.3 : Unplug from the main power outlet and restart according to the basic operation procedures.
For No.4-7
After the STAND BY indicator lights up, pull out the power cord and check the following items one-by one.
No.4 : Ensure that the lamp is correctly set in place. Restart according to the basic operation procedures.
No.5 : Check that nothing is blocking the air inlets, and wait until the inside cools down. Restart according to the basic operation
procedures.
No.6 : Check the ambient temperature. If it is normal, leave the projector until it cools down. Restart according to the basic
operation procedures.
No.7 : Leave the projector until it cools down. Restart according to the basic operation procedures.
If the same warning indication is observed again despite the instructions above, wait for the cooling fan to stop, check that the
STAND BY indicator on, then unplug the power cord and call your dealer for repair.
                             Indicator
LAMP TEMP STAND BY OPERATE
1Blink Blink
The light-source lamp does not light up and projection cannot be done.
2Blink Blink simultaneously Blink The light-source lamp suddenly goes off during projection.
3Blink BlinkCircuit operation is abnormal.
4Blink Blink alternately Blink The light-source lamp is misfitted.
5Blink
The internal temperature is abnormally high.
6Blink BlinkThe temperature at the air inlets has risen abnormally high.
7Blink Blink Blink BlinkThe cooling fan has stopped. (Fan locked)
* For details on individually blinking indicators, please see page 43.
Warning No. 
						

							52

 Model name/A rticle name  28A9017  D-ILA multimedia projector

  Emission method D-ILA®* (Reflective Active Matrix Principle)

 Display panel/ size D-ILA /0.7 (1400pixels x 1050pixels) x 3 (Total number of pixels: 4,410,000)

  Projecting lens   x 1.3 zoom lens (2.1:  ~2.6:1)  
  (Ma nual  zooming and  focusing)

  Light-source lamp 250W Ultra High Pressure Mercury lamp
[Part No.: BHL5006-S/Rating: 250W]

 Screen si ze   40 ~ 200 / (with aspect  ratio:  4:3)

  Projection distance  Approx.  1.6m ~ 12m 

  Color system NTSC, NTSC4.43, PAL, SECAM (Automatic switching/manual switching)

  Resolution 1400 dots x 1050 dots (S-XGA full resolution, during RGB input)
1000 TV lines (Horizontal resolution, aspect ratio 4:3, during video input)

  Scanning frequency Horizontal frequency : 15kHz~120kHz
Ve rtical frequency : 50Hz~120Hz
Please be sure to refer to the frequency correspondence table on page 20.

 Audio Power output: 1W (monaural), 4cm round type micro-speaker x 1

  Input terminals VIDEO IN Y/C 1-line, mini DIN 4 pin x 1
Y: 1.0 Vp-p, 75ohm C:0. 286 Vp-p, 75ohm(NTSC), 0.3Vp-p, 75ohm(PAL)
VIDEO 1-line, RCA pin x 1 1.0V(p-p),75ohm,synchronised
PC 1 1-line, D-sub 3-rows 15 pin x 1 
PC 2 1-line, BNC x 5
Y,  C
B,CR: Component (Y, B-Y, R-Y) signal (Color Difference signal)
Y,  P
B, PR:  DTV-format (Y, PB, PR) signal
R, G, B : Analog RGB signal
H/Cs, V : Horizontal (H) sync/composite (Cs) sync, Vertical (V) sync signal
PC3 1-line, DVI-D (single-24pin) terminal
A UDIO 1-line, RCApin X 1 (Y/C, VIDEO, PC1, PC2, PC3) 0.5V(rms), high impedance
CONTROL RS-232C : 2-lines, D-sub 9pin x1 (External controller) ❈ (IN : 1 system     OUT : 1 system)
REMOTE : 1-line, stereo mini-jack x1 (remote control)

  Output terminals DC OUT 5V, 1.5A DC Power Jack  

 Pow er requirements AC 100V ~ 240V AC, 50Hz/ 60Hz

 Pow er consumption 3.4 A (100V AC) ~ 1.42A (240V AC)

  Operation environment Temperature: 41°F ~ 95°F (+5°C ~ +35°C)
Humidity      : 20% ~ 80% (no condensation.)
[Preservation temperature    14°F ~ 140°F  (–10°C ~ +60°C)]


Dimensions (Width x Height x Length)Approx. 121/10”x  approx. 53/8”x  approx. 141/2”(Approx. 307mm x 136mm x 368mm)
(Excluding handle, foot, lens and protrusion portion)

  Mass  Approx.  13.0lbs (Appr ox.  5.9Kg) 

  Accessories ( ☞ page 6)
Specifications
• D-ILA® is the abbreviation for Direct drive Image Light Amplifier.
• Design and Specifications are subject to change without notice.
• D-ILA
®  devices are manufactured using extremely high-precision technology. Pixel effectiveness is 99.99%. Only 0.01% or less of
the pixels would either not lit up or remain permanently lit up.
• Please note that some pictures and illustrations may have been be abridged, enlarged or contextualized in order to aid compre- 
hension. Images may differ from the actual product.
• All brand names and products (IBM, Macintosh) herein are the trademarks or registered trademarks of their respective compa- 
nies.
• This product conforms to the ‘Household electric appliances and general-purpose articles harmonics control measure guideline’. 
						

							53
Dimensions (unit: mm)
Specifications
6M (Depth 10mm)
Attachment screw should be   
more than 6mm but less than 10mm in length.Center of lens
181 2067.5
298 27
298 300
360
A
89
267
115.9
65.4
15
20 ~ 56292
B
L D
LDAB
8.2 92.5 38.2 36.2
                              11.0  79.2
41.0 39.0

 Front 
 
Bottom

  To p

 Side 
						

							54
4
2
9
8
16
876
543213
1
11 12 13
6712 109 45 3 815 14
24
7
15
23
6
14
22
3
11
19
2
10
18 5
13
214
12
20
1
9
17
Specifications
Pin arrangement

 Y/C terminal
Pin number Signal name
1GND (Y)
2GND (C)
3Y
4C
Pin number Signal name
1N/C
2RD
3TD
4N/C
5GND
Pin number Signal name
6N/C
7N/C
8N/C
9N/C

 RS-232C IN/OUT terminal

 PC 1 terminal

 PC 3 terminal
Pin number Signal name
1Red
2Green
3Blue
4N/C
5N/C
6GND (Red)
7GND (Green)
8GND (Blue)
Pin number Signal name
9N/C
10 GND (SYNC)
11 GND
12 N/C
13 H.SYNC
14 V.SYNC
15 N/C
Pin number Signal name
1TMDS data 2 -
2 TMDS data 2 +
3TMDS data 2 /4 shield
4N/C
5N/C
6DDC clock
7DDC data
8N/C
9TMDS data 1 -
10 TMDS data 1 +
11 TMDS data 1/3 shield
12 N/C
Pin number Signal name
13 N/C
14 TMDS +5V power supply
15 Earth (+5V)
16 Hot plug detection
17 TMDS data 0 -
18 TMDS data 0+
19 TMDS data 0/5 shield
20 N/C
21 N/C
22 TMDS clock shield
23 TMDS clock +
24 TMDS clock -
TMDS = Transition Minimized Differential Signaling
DDC = Display Data Channel 
						

							55
Specifications

 RS-232C external control
By connecting a computer to the projector with a RS-232C cross cable (D-sub 9 pins), you can control the projector with the
computer. The commands to control the projector and the response data format against the received commands are explained
here.
For details, please consult the authorized dealer where you purchased your projector.
1. Communication Specifications
The communication specifications are as follows.
Baud rate 9600bps/19200bps
Data length 8 bits
Parity None
Stop bit 1 bit
Flow control None
2. Command Format
2-1 Command data format
When sending a control command to the projector, use the following data format.
HeaderIDSPParameterCommandSP
CR[[
Header : Designates the head of data and the data type.
: ‘!’ (21h): Assigns command to the projector.
: ‘?’ (3Fh): Query to the projector. (Asking command)
ID : ‘1’: The identification number of the projector. (Manufacturer set value ‘1’)
SP : Designates the delimiter for ID, Command, and Parameter. (20h)
CR : Designates the terminal of the data. (0Dh)
* [  ] is not necessary for Asking command.
2-2 Response data format
Upon executing a control command it has received, the projector sends back the following response data to the computer:
HeaderIDSPParameterNormal Termination  StatusSP
CR[[
Header : Designates the head of data.
: ‘@’ (40h): Fetches data from the projector.
ID : ‘1’: The identification number of the projector. (Manufacturer set value”1”)
SP : Designates the delimiter for ID, Command, and Parameter. (20h)
Normal Termination Status : ‘0’ (30h)
CR : Designates the terminal of the data. (0Dh)
2-3 Parameters used for the data format
The following three kinds of parameters are used for control commands and response data.
1)  Numeric value
2)  ON/OFF
3)  Special parameters
Each parameter is as follows:
1) Numeric value
A 2-byte hexadecimal value (sign included) is represented by a set of 4 digit (4 bytes) characters.
Designated range: ‘8000’ to ‘7FFF’.
2) ON/OFF
Shows the status (ON/OFF) of the projector, such as POWER and HIDE.
Character Hex. Meaning
‘0’ 30 OFF
‘1’ 31 ON 
						

							56
Specifications
3) Special parametersInput switching parameters
Character Hex. Meaning
‘0’ 30 Y/C
‘1’ 31 VIDEO
‘3’ 33 PC1
‘4’ 34 PC2
‘5’ 35 PC3
Operation mode parameters
Character Hex. Meaning
‘0000’ 30h 30h 30h 30h Stand-by mode
‘0001’ 30h 30h 30h 31h Power-on mode
‘0002’ 30h 30h 30h 32h Cool-down mode
‘0004’ 30h 30h 30h 34h Emergency mode
Function CommandAsking Data type
Power on ELSENumeric ValueON/OFF Special Data
OPERATE U0F X X X
X
HIDE U00
XX
X
Right Left reversalU17
XX
X
Top Bottom inversionU18
XX
X
Input switch U1A
XX XY/C ...
Operation modeZ03

XX Stand-by…
Operation mode: Only Asking command is possible.
3. External control command table 
						

							LEGAL INFORMATION
FIVE-YEAR LIMITED  WARRANTY 
This Dukane LCD projector is w arranted to the or iginal purchaser f or a period of 
five (5) y ears from the or iginal purchase date - in nor mal use and service -
against defects in mater ial and workmanship . DUKANE CORPORA TION
EXPRESSLY DISCLAIMS ALL O THER WARRANTIES OF MERCHANT ABILITY
AND FITNESS FOR A PARTICULAR PURPOSE.
Dur ing the w arranty per iod, Dukane Cor poration will repair or replace (at the
man ufacturers option) an y such defective par ts (except f or the lamp , which is 
subject to whate ver w arranties the man ufacturer ma y provide) without charge to
the purchaser f or parts or labor when the product is retur ned, prepaid and insured,
with proof-of-purchase date.  This remedy is v oid if the product has been 
damaged by accident, unreasonab le use, neglect, improper ser vice or other 
causes not arising out of def ects in material or workmanship .
Dukane Cor poration disclaims all liability f or incidental or consequential damage 
of any kind, including all damages ar ising out of any interruptions in oper ation of 
the product and all damages to softw are.
No person, fir m, or representativ e is authorized to assume an y obligation or to 
make an y warranty on behalf of the Dukane Cor poration other than as stated 
abo ve .
        THIS LIMITED  WARRANTY IS  VALID FOR U .S.A AND CANAD A.
           FOR OTHER LOCATIONS, LOCAL  WARRANTIES APPL Y.
	 			SERVICE & REP AIR
For ser vice and par ts, contact the Dukane A V Service Depar tment 
at 1 (800) 676-2487 within the USA or 1 (630) 584-2300 w orldwide . 
If y ou w ould lik e to send a f acsimile (FAX), dial 1 (630) 584-5156 w orldwide .
When requesting w arranty ser vice, please ha ve the sales receipt a vailab le along 
with the model name and ser ial number .
If it becomes necessar y to return the projector , use the original packing mater ial 
and box (if retained) or pac k securely. Dukane Cor poration will not be liab le for 
any pic k-up or deliv ery charges or an y expenses incurred f or service calls or 
service supplied b y anyone other than the Dukane A V Service Depar tment. 
						

							Dukane Corporation
Audio Visual Products Division
2900 Dukane Drive
St. Charles, IL 60174-3395
E-mail: [email protected]
Phone: (630) 762-4040
Orders: (800) 676-2485
Information: (800) 676-2486
Fax: (630) 584-5156
Parts & Service: (800) 676-2487
Fax: (630) 584-0984
Audio Visual Products
Par t # 401-602-00