Dukane Imagepro 8949h Projector Users Manual

							
51

OPTION Menu

OPTION Menu (continued)

ItemDescription
SECURITY
(continued)
2.2-4   Move the cursor to the right side of the 
PASSWORD AGAIN BOX and press the 
► button to display the PASSWORD for 
about 20 seconds, please make note of the 
PASSWORD during this time. 
Pressing the 

ENTER button on the remote control 
or 
INPUT  button on the projector will return to 
MyScreen PASS WORD on/off menu.
When a PASSWORD is set for MyScreen:
• The MyScreen registration function (and menu) will be unavailable.
• The MyScreen Lock menu will be unavailable.
• The START UP setting will be locked on MyScreen (and the menu will be 
unavailable).
Turning the MyScreen PASSWORD off will allow normal operation of these 
functions.
• Please do not forget your MyScreen PASSWORD.
2.3 Turning the PASSWORD off
2.3-1   Follow the procedure in 2.1-1 to display the MyScreen  PASSWORD 
on/off menu.
2.3-2 
 Select TURN OFF to display the ENTER PASSWORD BOX (large). 
Enter the registered PASSWORD and the screen will return to the 
MyScreen on/off menu.
If an incorrect PASSWORD is input, the menu will close. If necessary, repeat 
the process from 2.3-1.
2.4 If you have forgotten your PASSWORD
2.4-1   Follow the procedure in 2.1-1 to display the MyScreen PASSWORD 
on/off menu.
2.4-2 
 Select TURN OFF to display the ENTER 
PASSWORD BOX (large). The 10 digit 
Inquiring Code will be displayed inside the 
BOX.
2.4-3 
 Contact your dealer with the 10 digit Inquiring 
Code. Your PASSWORD will be sent after 
your user registration information is confirmed.
3. Using the PIN LOCK FunctionPIN LOCK is a function which prevents the projector from being used unless 
a registered Code is input.
3.1 Registering the PIN Code
3.1-1  Use the ▲/▼ buttons on the SECURITY menu 
to select PIN LOCK and press the ► button 
or the 

ENTER button to display the PIN LOCK 
on/off menu.
3.1-2 
 
Use the ▲/▼ buttons on the PIN LOCK on/off 
menu to select TURN ON and the PIN BOX 
will be displayed. 
ENTER PASSWORD  BOX (large)
NOTE PASSWORD 
BOX
(continued on next page)
PIN LOCK on/off menu 
						

							
52

OPTION Menu

OPTION Menu (continued)

ItemDescription
SECURITY
(continued)
3.1-3    Input a 4 part PIN Code using the ▲/▼/◄/►/
RGB and 
INPUT  buttons. 
The PIN CODE AGAIN BOX will appear. 
Reenter the same PIN Code. This will 
complete the PIN Code registration.
• If there is no key input for about 55 seconds while 
the PIN BOX or the PIN CODE AGAIN BOX is 
displayed, the menu will close. If necessary, repeat 
the process from 3.1-1.
Afterwards, anytime the projector is restarted after 
the power switch is turned off the PIN BOX will be 
displayed. Enter the registered PIN Code.
The projector can be used after entering the 
registered PIN Code. If an incorrect PIN Code is 
input, the PIN BOX will be displayed again.
If an incorrect PIN Code is input 3 times, the projector will turn of f. 
Afterwards the projector will turn off every time an incorrect PIN Code is 
input. The projector will also turn off if there is no key input for about 5 
minutes while the PIN BOX is displayed.
This function will activate only when the projector is started after the power 
switch was turned off.
• Please do not forget your PIN Code.
3.2 Turning Off the PIN LOCK Function
3.2-1   Follow the procedure in 3.1-1 to display the PIN LOCK on/off menu. 
Use the ▲/▼ buttons to select TURN OFF and the PIN BOX will be 
displayed.  
Enter the registered PIN Code to turn the PIN LOCK function off.
If an incorrect PASSWORD is input 3 times, the menu will close.
3.3 If you have forgotten your PIN Code
3.3-1   While the PIN BOX is displayed, press and 
hold the RESET  button for three seconds 
or press and hold the 
INPUT  button for 3 
seconds while pressing the ► button on the 
projector.
• If there is no key input for about 5 minutes while 
the Inquiring Code is displayed, the projector will 
turn off.
3.3-2 
 Contact your dealer with the 10 digit Inquiring Code. Your PASSWORD 
will be sent after your user registration information is confirmed.
PIN BOX
PIN CODE AGAIN BOX
Inquiring Code (PIN Code)
(continued on next page) 
						

							
53

OPTION Menu

OPTION Menu (continued)

ItemDescription
SECURITY
(continued)
4. Using the Transition Detector Function
While the Transition Detector function is ON, when power switch is started to 
supply to the projector, it might react as below.
• Transition Detector alarm shown below might appear on screen, if the 
projector has been moved or re-installed.
• Transition Detector alarm might appear on screen, if the MIRROR setting 
has been changed.
• Keystone adjustment feature has been prohibited as long as the Transition 
Detector function is ON.
4.1 Turning On the Transition Detector Function
4.1-1   Use the ▲/▼ buttons on the SECURITY menu to 
select Transition Detector and press the ► or the 

ENTER button to display the Transition Detector on/
off menu. Select TURN ON and the current angle 
and mirror setting will be recorded.
• This feature may not function properly if the projector is 
not in a stable position when TURN ON is selected.
4.1-2   If this function is set to TURN ON when the 
vertical angle of the projector or mirror setting 
at which the projector is turned on is different 
than the previously recorded, the Transition 
Detector Alarm will be displayed and the 
projector will not display the input signal.
Set the Transition Detector off in the SECURITY menu to display the input signal.
If the Transition Detector ALARM is displayed for about 5 minutes, the lamp will turn 
off. 
This function will activate only when the projector is started after the power 
switch was turned off.
4.2 Setting the Transition Detector PASSWORD
4.2-1  Use the ▲/▼ buttons on the SECURITY menu to select Transition 
Detector and press the ► or the 
ENTER button to display the 
Transition Detector on/off menu.
4.2-2 
 
Use the ▲/▼ buttons on the Transition 
Detector on/off menu to select TURN ON. 
The ENTER PASSWORD BOX (small) will be 
displayed.
4.2-3 
 Use the ▲/▼/◄/► buttons to enter a 
PASSWORD. Move the cursor to the right side of 
the ENTER PASSWORD BOX (small) and press 
the 
► button to display the PASSWORD AGAIN 
BOX, enter the same PASSWORD again.
4.2-4   Move the cursor to the right side of the 
PASSWORD AGAIN BOX and press the 
► button to display the PASSWORD for 
about 20 seconds, please make note of the 
PASSWORD during this time.
Pressing the 

ENTER button on the remote control or 
the 
INPUT  button on the projector will return to the 
Transition Detector on/off menu.
• Please do not forget your Transition Detector PASSWORD.

Transition Detector on/
off menu
Transition Detector  Alarm

ENTER PASSWORD BOX 
(small)
PASSWORD AGAIN BOX
NOTE PASSWORD BOX
(continued on next page) 
						

							
54

OPTION Menu

OPTION Menu (continued)

ItemDescription
SECURITY
(continued) 4.3 Setting the Transition Detector off
4.3-1 
 Follow the procedure in 4.1-1 to display the Transition Detector on/off 
menu.
4.3-2 
 Select TURN OFF to display the ENTER PASSWORD BOX (large). 
Enter the registered PASSWORD and the screen will return to the 
Transition Detector on/off menu.
If an incorrect PASSWORD is input, the menu will close. If necessary, repeat 
the process from 4.3-1.
4.4 If you have forgotten your PASSWORD
4.4-1   Follow the procedure in 4.1-1 to display the Transition Detector on/off 
menu.
4.4-2 
 
Select TURN OFF to display the ENTER 
PASSWORD BOX (large). The 10 digit Inquiring 
Code will be displayed inside the BOX.
4.4-3  Contact your dealer with the 10 digit Inquiring 
Code. Your PASSWORD will be sent after your 
user registration information is confirmed.
5. Using the MY TEXT PASSWORD function
This item allows you to display your own message (MY TEXT) on the START 
UP screen and INPUT-INFORMATION. It can be protected by a password to 
prevent it from being overwritten.
5.1 Writing the MY TEXT
(1)  Use the ▲/▼ buttons on the SECURITY menu 
to select the MY TEXT WRITING menu and 
press the ► button. The MY TEXT WRITING 
dialog will be displayed.
(2) 
 The current MY TEXT will be displayed on the first 3 
lines. If not yet written, the lines will be blank.
Use the 
▲/▼/◄/► buttons and the 
ENTER or 
INPUT  button to select and enter 
characters. The RESET  button can be used to erase 1 character at a time. Also if 
you move the cursor to DELETE or ALL CLEAR on screen and push the 
ENTER 
or 
INPUT  button, 1 character or all characters will be erased. The MY TEXT can 
be input up to 24 characters on each line.
(3)   To change an already inserted character, press 
the ▲/▼ button to move the cursor to one of 
the first 3 lines, and use the ◄/► buttons to 
move the cursor on the character to be changed. 
After pressing the 

ENTER or 
INPUT  button, the 
character is selected. Then, follow the same 
procedure as described at the item (2) above.
(4) 
 
To finish entering text, move the cursor to the 
SAVE on screen and press the 

ENTER or 
INPUT  
button. To revert to the previous MY TEXT 
without saving changes, move the cursor to the 
CANCEL on screen and press the 

ENTER or 
INPUT  button.
• The MY TEXT WRITING function is available only when the MY TEXT 
PASSWORD function is set to TURN OFF.

ENTER PASSWORD BOX  (large)
(continued on next page) 
						

							
55

OPTION Menu

OPTION Menu (continued)

ItemDescription
SECURITY
(continued) 5.2 Displaying the MY TEXT
(1) 
 Use the ▲/▼ buttons on the SECURITY menu 
to select the MY TEXT DISPLAY menu and 
press the ► button to display the MY TEXT 
DISPLAY on/off menu.
(2) 
 Use the ▲/▼ buttons on the MY TEXT DISPLAY 
on/off menu to select on or off.
TURN ON  ó TURN OFF
When it is set TURN ON, the MY TEXT will be 
displayed on the START UP screen and the INPUT-
INFORMATION- when the INFORMATION on the 
SERVICE menu is chosen.
• This function is available only when the MY TEXT 
PASSWORD function is set to the TURN OFF.
5.3 Turning on the MY TEXT PASSWORDThe MY TEXT PASSWORD function can prevent the MY TEXT from being overwritten.
5.3-1 
 Turning on the MY TEXT PASSWORD function
(1)   Use the ▲/▼ buttons on the SECURITY menu 
to select the MY TEXT PASSWORD menu and 
press the ► button to display the MY TEXT 
PASSWORD on/off menu.
5.3-2 
 Setting the MY TEXT PASSWORD
(1) 
 Display the MY TEXT PASSWORD on/off menu 
using the procedure in 5.3-1
(2) 
 Use the ▲/▼ buttons on the MY TEXT 
PASSWORD menu to select TURN ON. The 
ENTER PASSWORD BOX (small) will be 
displayed.
(3) 
 Use the ▲/▼/◄/► buttons to enter the 
PASSWORD. Move the cursor to the right side of 
the ENTER PASSWORD BOX (small) and press 
the ► button to display the PASSWORD AGAIN 
BOX, and then enter the same PASSWORD 
again.
(4) 
 Move the cursor to the right side of the 
PASSWORD AGAIN BOX and press ► button to 
display the PASSWORD for about 20 seconds, 
then please make note of the PASSWORD 
during this time.
Pressing the 

ENTER button on the remote control 
or 
INPUT  button on the projector will return to the 
MY TEXT PASSWORD on/off menu. When the 
PASSWORD is set for the MY TEXT;
• The MY TEXT DISPLAY menu will be unavailable, which can prohibit 
changing the DISPLAY setting.
• The MY TEXT WRITING menu will be unavailable, which can prevent the 
MY TEXT from being overwritten.
MY TEXT DISPLAY on/ off menu
ENTER PASSWORD BOX  (small)
PASSWORD AGAIN BOX 
NOTE PASSWORD BOX 
(continued on next page)
MY TEXT PASSWORD on/off menu 
						

							
56

OPTION Menu

OPTION Menu (continued)

ItemDescription
SECURITY
(continued)
5.3-3   Turning the MY TEXT PASSWORD off
(1)   Follow the procedure in 5.3-1 to display the MY 
TEXT PASSWORD on/off menu.
(2) 
 Select TURN OFF to display the ENTER 
PASSWORD BOX (large). Enter the registered 
PASSWORD and the screen will return to the 
MY TEXT PASSWORD on/off menu. 
If an incorrect PASSWORD is input, the menu will close. If necessary, repeat 
the process from 5.3-3(1)
5.3.4 If you have forgotten your PASSWORD.
(1) 
 Follow the procedure in 5.3-1 to display the MY TEXT PASSWORD on/
off menu.
(2) 
 Select TURN OFF to display the ENTER PASSWORD BOX (large). The 
10 digit inquiring code will be displayed inside the box. 
(3) 
 Contact your dealer with the 10 digit inquiring code. Your PASSWORD 
will be sent after your user registration information is confirmed.
ENTER PASSWORD BOX  (large) 
						

							
57

NETWORK Menu
Remember that incorrect network settings on this projector 
may cause trouble on the network. Be sure to consult with 
your network administrator before connecting to an existing 
access point on your network.
Select “NETWORK” from the main menu to access the 
following functions. 
Select an item using the ▲/▼ cursor buttons on the projector or remote control, 
and press the ► cursor button on the projector or remote control, or 

ENTER 
button on the remote control to execute the item. Then perform it according to the 
following table.
See the User’s Manual - Network Guide for details of NETWORK operation.
NETWORK Menu
• If you are not utilizing SNTP ( Date/Time Settings of the User’s 
Manual - Network Guide) , then you must set the DATE AND TIME during the 
initial installation. NOTE

Item Description
SETUP Selecting this item displays the SETUP Menu 
for the network.
Use the ▲/▼ buttons to select an item, and 
the ► or 

ENTER button on the remote control 
to perform the item.
DHCP (Dynamic  Host 
Configuration  Protocol)
Use the ▲/▼ buttons to turn DHCP on/off.
ON 
ó  OFF
Select OFF when the network does  
not have DHCP enabled.
• When the “DHCP” setting changes to “ON”, it takes a 
little time to obtain IP address from DHCP server.
• Auto IP function will be assigned an IP address if the 
projector could not obtain an IP address from server 
even if DHCP is “ON”.
(continued on next page) 
						

							
58

NETWORK Menu

NETWORK Menu (continued)

ItemDescription
SETUP
(continued)
IP 
ADDRESS
Use the ▲/▼ /◄/► buttons to 
enter the IP ADDRESS. This 
function can only be used when 
DHCP is set to OFF.
• The IP ADDRESS is the number that identifies this 
projector on the network. You cannot have two devices 
with the same IP ADDRESS on the same network.
• The IP ADDRESS “0.0.0.0” is prohibited.
SUBNET  MASK Use the ▲/▼
/◄/► buttons to 
enter the same SUBNET MASK 
used by your PC. This function 
can only be used when DHCP is 
set to OFF.
•  The SUBNET MASK ”0.0.0.0” is prohibited.
DEFAULT 
GATEWAY
Use the ▲/▼ /◄/► buttons to 
enter the DEFAULT GATEWAY 
(a node on a computer network 
that serves as an access point to 
another network) address.
This function can only be used when DHCP is set to 
OFF.
DNS 
SERVER Use the ▲/▼/◄/► buttons to 
input the DNS server address. The 
DNS server is a system to control 
domain names and IP addresses 
on the Network. 
TIME 
DIFFERENCE
Use the ▲/▼  buttons to enter the 
TIME DIFFERENCE. 
Set the same TIME DIFFERENCE 
as the one set on your PC. If 
unsure, consult your IT manager. 
Use the ◄ button to return to 
the menu after setting the TIME 
DIFFERENCE.
DATE  AND 
TIME Use the ▲/▼
/◄/► buttons to 
enter the Year (last two digits), 
Month, Date, Hour and Minute.
• The projector will override this setting and retrieve 
DATE AND TIME information from the Time server 
when SNTP is enabled.  (
 Date/Time Settings of the 
User’s Manual - Network Guide)
(continued on next page) 
						

							
59

NETWORK Menu

NETWORK Menu (continued)

ItemDescription
PROJECTOR  NAME (1) 
 Use the▲/▼ buttons on the NETWORK Menu to select the 
PROJECTOR NAME menu and press the  ► button. The 
PROJECTOR NAME dialog will be displayed.
(2) 
 The current PROJECTOR NAME 
will be displayed on the first 3 lines. 
If not yet written, the lines will be 
blank. 
Use the ▲/▼/◄/► buttons and 
the 

ENTER or 
INPUT button to 
select and enter characters. The 
RESET  button can be used to 
erase 1 character at a time. Also if 
you move the cursor to DELETE or 
ALL CLEAR on screen and push 
the 

ENTER or 
INPUT  button, 1 
character or all characters will be 
erased.
The PROJECTOR NAME can be 
input up to 64 characters.
(3) 
 
To change an already inserted 
character, press the ▲/▼ button to 
move the cursor to one of the first 3 
lines, and use the ◄/► buttons to 
move the cursor on the character 
to be changed. After pressing 
the 

ENTER or 
INPUT  button, the 
character is selected. Then, follow 
the same procedure as described at 
the item (2) above.
 (4) 
 
To finish entering text, move the 
cursor to the SAVE on screen 
and press the 

ENTER or 
INPUT  
button. To revert to the previous 
PROJECTOR NAME without saving 
changes, move the cursor to the 
CANCEL on screen and press the 

ENTER or 
INPUT  button.
(continued on next page) 
						

							
60

NETWORK Menu

NETWORK Menu (continued)

ItemDescription
MY IMAGE Selecting this item displays the 
MY 
IMAGE menu. 
The application software “PJImage” 
is required to store image(s) into the 
projector.
Use the ▲/▼ buttons to select an item which is a still image by the 
MY IMAGE  (
 MY IMAGE (Still Image Transfer) Display of the 
User’s Manual - Network Guide)  and the ► or 
ENTER button to 
display the image.
• The item without image stored cannot be selected.
• The image names are each displayed in 16 characters or less.
To switch the image displayed 
Use the ▲/▼ buttons.
To return to the menu
Press the ◄ or 

ESC button on the remote control.
To erase the image displayed and its source file in the projector.
(1)   Press the RESET  button on the 
remote control while displaying an 
image to display the MY IMAGE 
RESET menu. 
(2) 
 
Press the 

ENTER button on the remote control or the 
INPUT  
button on the projector to perform to erase.  
To stop erasing, press the 

ESC button on the remote control or 
the ◄ button on the projector.
(continued on next page)