Dukane Imagepro 8949h Projector Users Manual

							
11

Setting up

Connecting your devices (continued)
• Be sure to read the manuals for devices before connecting them to the projector, 
and make sure that all the devices are suitable to be connected with this product. Before 
connecting to a PC, check the signal level, the signal timing, and the resolution.
-   Be sure to consult to the administrator of the network. Do not connect 
LAN port to any 
network that might have the excessive voltage.
- Some signal may need an adapter to input this projector.
- 
 
Some PCs have multiple screen display modes that may include some signals which 
are not supported by this projector.
- 
 
Although the projector can display signals with resolution up to UXGA (1600X1200), the signal will be 
converted to the projector’s panel resolution before being displayed. The best display performance 
will be achieved if the resolutions of the input signal and the projector panel are identical.
• While connecting, make sure that the shape of the cable's connector fits the port to 
connect with. And be sure to tighten the screws on connectors with screws.
• When connecting a laptop PC to the projector, be sure to activate the PC’s external 
RGB output. (Set the laptop PC to CRT display or to simultaneous LCD and CRT 
display.) For details on how this is done, please refer to the instruction manual of the 
corresponding laptop PC.
• When the picture resolution is changed on a computer depending on an input, 
automatic adjustment function may take some time and may not be completed. In this 
case, you may not be able to see a check box to select “Yes/No” for the new resolution 
on Windows. Then the resolution will go back to the original. It might be recommended 
to use other CRT or LCD monitors to change the resolution.
• In some cases, this projector may not display a proper picture or display any picture on 
screen. For example, automatic adjustment may not function correctly with some input 
signals. An input signal of composite sync or sync on G may confuse this projector, so 
the projector may not display a proper picture.
• 
The 
HDMI port of this model is compatible with HDCP (High-bandwidth Digital Content Protection) 
and therefore capable of displaying a video signal from HDCP compatible DVD players or the like.
NOTE
About Plug-and-Play capability
Plug-and-Play is a system composed of a computer, its operating system and peripheral 
equipment (i.e. display devices). This projector is VESA DDC 2B compatible. Plug-and-
Play can be used by connecting this projector to a computer that is VESA  DDC (display 
data channel) compatible.
• 
Take advantage of this feature by connecting an RGB cable to the RGB1 port (DDC 2B 
compatible). Plug-and-Play may not work properly if any other type of connection is attempted.
• Please use the standard drivers in your computer as this projector is a Plug-and-Play monitor.
NOTE for HDMI
• The 
HDMI supports the following signals.
  -Video signal : 480i@60,480p@60,576i@50,720p@50/60,1080i@50/60,1080p@50/60
  -PC signals : See User’s Manual (detailed) Technical
  -Audio signal : 
 Format    Linear PCM 
Sampling Frequency   48kHz / 44.1kHz / 32kHz
• This projector can be connected with another equipment that has HDMI or DVI 
connector, but with some equipment the projector may not work properly, something like 
no video or no audio.
• 
 
Be sure to use an HDMI cable that has the HDMI logo.
• 
When the projector is connected with a device having DVI connector, use a DVI to HDMI cable 
to connect with the 
HDMI input and an audio cable to connect with one of the AUDIO input. 
						

							
12

Setting up
Connecting power supply
1.Connect the connector of the power cord to the AC IN (AC inlet) of the 
projector.
2.Firmly plug the power cord's plug into the outlet. 

►Please use extra caution when connecting the power cord, as 
incorrect or faulty connections may result in fire and/or electrical shock.
• Only use the power cord that came with the projector. If it is damaged, contact 
your dealer to get a new one.
• Only plug the power cord into an outlet whose voltage is matched to the power 
cord. The power outlet should be close to the projector and easily accessible. 
Remove the power cord for complete separation.
• Never modify the power cord. WARNING

AC IN
to the outlet

Connector of the power cord 
						

							
13

Remote control
Remote control
Laser pointer
This remote control has a laser pointer in place of a finger or rod.  The laser beam 
works and the 

LASER INDICATOR lights while the 
LASER button is pressed.

►The laser pointer of the remote control is used in place of 
a finger or rod. Never look directly into the laser beam outlet or point the laser 
beam at other people. The laser beam can cause vision problems. WARNING

►Use of controls or adjustments or performance of procedures 
other than those specified herein may result in hazardous radiation exposure. CAUTION

Installing the batteries
Please insert the batteries before using the remote control. If the remote control starts to 
malfunction, replace the batteries. If you will not use the remote control for an extended 
period, remove the batteries from the remote control and store them in a safe place.
1.Slide back and remove the 
battery cover in the direction 
of the arrow.
2.Align and insert the two AA batteries 
(HITACHI MAXELL, Part No.LR6 
or R6P) according to their plus and minus terminals as indicated in the remote control.
3.Replace the battery cover in the direction of the arrow and snap it back into place.

►Always handle the batteries with care and use them only as 
directed. Improper use may result in battery explosion, cracking or leakage, 
which could result in fire, injury and/or pollution of the surrounding environment.
• Be sure to use only the batteries specified. Do not use batteries of dif ferent 
types at the same time. Do not mix a new battery with used one.
• 
Make sure the plus and minus terminals are correctly aligned when loading a battery.
• Keep a battery away from children and pets.
• Do not recharge, short circuit, solder or disassemble a battery .
• 
Do not place a battery in a fire or water. Keep batteries in a dark, cool and dry place.
• If you observe battery leakage, wipe out the leakage and then replace a battery. 
If the leakage adheres to your body or clothes, rinse well with water immediately .
• Obey the local laws on disposing the battery. WARNING

BLANK
LASER
ASPECT
PUSH  ENTER PAGE UP
LASER
INDICATORMY SOURCE/
DOC.CAMERASEARCH
STANDBY/ON
VIDEORGB
PAGE DOWNESCMENU RESET
POSITION AUTOPbyPMAGNIFYON
OFFMY BUTTON1
2VOLUME+
-
FREEZE KEYSTONE MUTE

LASER INDICATOR

LASER button 
						

							
14

Remote control

Approx.3 m 
30º
30º
30º 30º Approx.
3 m 
20º 20º Approx.
3 m 
About the remote control signal
The remote control works with the projector’s remote sensors. This projector has 
three remote sensors on the front, on the top, and on the back.
The sensors can be respectively turned active or inactive using the “REMOTE 
RECEIV.” in the SERVICE item of OPTION Menu (
 48). Each sensor senses the 
signal within the following range when the sensor is active.
The front and top sensors:
60 degrees (30 degrees to the left and right of the 
sensor) within 3 meters about.
The back sensor:
40 degrees (20 degrees to the left and right of the 
sensor) within 3 meters about.
• The remote control signal reflected in 
the screen or the like may be available. If it is 
difficult to send the signal to the sensor directly, 
attempt to make the signal reflect.
• The remote control uses infrared light to send 
signals to the projector (Class 1 LED), so be 
sure to use the remote control in an area free 
from obstacles that could block the remote 
control’s signal to the projector.
• The remote control may not work correctly if 
strong light (such as direct sun light) or light 
from an extremely close range (such as from 
an inverter fluorescent lamp) shines on the 
remote sensor of the projector. Adjust the 
position of projector avoiding those lights. NOTE
Changing the frequency of  remote control signal
The accessory remote control has the choice of 
the mode 1 or the mode 2, in the frequency of 
its signal. If the remote control does not function 
properly, attempt to change the signal frequency.
Please remember that the “REMOTE FREQ.” in 
SERVICE item of OPTION Menu (
 48) of the 
projector to be controlled should be set to the 
same mode as the remote control.
To set the mode of the remote control, slide the 
knob of the frequency switch inside the battery 
cover into the position indicated by the mode 
number to choose.

2  1

Back of the 
remote control
Inside of 
the battery cover
Frequency switch 
						

							
15

Remote control

Using as a wired remote control
The accessory remote control works as a wired remote control, 
when the wired control port at the bottom of the remote control 
connects with the 
REMOTE CONTROL port on the back of the 
projector via an audio cable with 3.5 diameter stereo mini plugs.
When the remote control signal is hard to reach surely to 
the projector in the environment, this function is effective.
• To connect the remote control with the projector, use an audio cable 
with 3.5 diameter stereo mini plugs. NOTE
Using as a simple PC mouse & keyboard
The accessory remote control works as a simple mouse and 
keyboard of the PC, when the projector’s 
USB port(B type) 
connect with the PC’s USB port(A type) via a USB cable. 
(1)   Mouse left button  
Pushing the button into the center point works 
instead of clicking the mouse's left button. 
Tilting this button to one of eight directions moves 
the PC's move pointer on the screen in the direction.
(2)  Mouse right button  
Pressing the button works instead of clicking 
the mouse’s right button.
(3) 
 Lever switch 
Sliding toward the side marked ▲ works instead of the 
[↑] key on the keyboard. Sliding toward the side marked 
▼ works instead of the [↓] key on the keyboard.
(4)  Cursor button ◄  
This button works instead of the [←] key on the keyboard.
(5)  Cursor button ►  
This button works instead of the [→] key on the keyboard.
(6) 
 PAGE UP button  
This button works instead of the PAGE UP key on the key board.
(7) 
 PAGE DOWN button   
This button works instead of the PAGE DOWN key on the key board.

BLANK LASER
ASPECT
PUSH  ENTER PAGE UP
LASER
INDICATORMY SOURCE/
DOC.CAMERASEARCH
STANDBY/ON
VIDEORGB
PAGE DOWNESCMENU RESET
POSITION AUTOPbyPMAGNIFYON
OFFMY BUTTON1
2VOLUME+
-FREEZE KEYSTONE MUTE

BLANK LASER
ASPEC T
 ESC  MENU  RESET
   
  POSITION  AUTO 
 
 M AGNIFY 
MY BUTTO N VOLUME
  ON  1
    MUTE
  OFF  2
  FREEZE  KEYSTONE  SEARCH
 
PUSH ENTER
 PAGE UP   PAGE DOWN
 STANDBY/ON VIDEO  RGBLASER
INDICATOR

(3)
(4)
(6) (2)
 
(5)
(7)
(1)

• When the simple mouse & keyboard function of this product does not 
work correctly, please check the following.
- 
 
When a USB cable connects this projector with a PC having a built-in pointing device (e.g. track 
ball) like a notebook PC, open BIOS setup menu, then select the external mouse and disable 
the built-in pointing device, because the built-in pointing device may have priority to this function.
-   Windows 95 OSR 2.1 or higher is required for this function. And also this 
function may not work depending on the PC’s configurations and mouse drivers. 
- Operating simultaneously two or more keys is void except for mouse drag and drop operation.
- This function is activated only when the projector is working properly. NOTE

  AUX I/O  
DC 5V 0.5A   LAN 
AC IN 
I       O 
SD CARD 
S D  C AR D 
LAN 
AC IN 
I       O 
VIDEO
CONTROL
AUDIO IN 
1
AUDIO IN  2
AUDIO OUT
RGB
 OU T RGB1
RGB2HDMI
 R  
           L     R           L
      AUDO IN 3        AUDIO IN  4
CB/PBY
CR/PR
B/CB/PBB/CR/PRG/Y
HV
USBREMOTE 
CONTROL
   
VIDEO
CONTROL
AUDIO IN 
1
AUDIO IN  2
AUDIO OUT
RGB
 OU T RGB1
RGB2HDMI
 R  
           L     R           L
      AUDO IN 3        AUDIO IN  4
CB/PBY
CR/PR
B/CB/PBB/CR/PRG/Y
HV
USBREMOTE 
CONTROL
   

to a PC
USB port

LAN

AC IN
I   O
VIDEO
CONTROL
AUDIO IN1
AUDIO IN2
AUDIO OUT
RGB
 OUTRGB1
RGB2
HDMI
 R             L      R           L
     AUDIO IN3        AUDIO IN4
CB/PBY CR/PR
B/CB/PBR/CR/PRG/Y
HV
USBREMOTE 
CONTROL
   
S-VIDEO

BL
ANK LASER
ASPECT
P U SH  ENT
ER PAGE UP
LASER
INDICATORMY SOU RCE/
DOC.CAMER ASEARCH
STANDBY/ON
VIDEORGB
PAGE DOWNESC MENU RESET
POSITION AUTOPbyPMAG
NIFYON
OFFMY BUTTO N1
2VOLUME+
-FREEZE KEYSTONE MUTE 
						

							
16

Contents
Power on/off

BLANKLASER
ASPECT
PUSH  ENTER PAGE UP
LASER
INDICATORMY SOURCE/
DOC.CAMERASEARCH
STANDBY/ON
VIDEORGB
PAGE DOWNESCMENU RESET
POSITION AUTOPbyPMAGNIFYON
OFFMY BUTTON1
2VOLUME+
-FREEZE KEYSTONE MUTE

1.Make sure that the power cord is firmly and 
correctly connected to the projector and the outlet.
Turning on the power
2.Remove the lens cover, and set the power switch 
to the ON position (marked 
“ 
I ”).  
The 
POWER indicator will light up in steady orange 
(
 69). Then wait several seconds because the 
buttons may not function for these several seconds. 
3.Press the STANDBY/ON button on the projector or 
the remote control.
• Turn the power on/off in right order. Please power on the projector prior 
to the connected devices. Power off the projector later than the connected devices.
• When the AUTO ON of the OPTION Menu is set to the TURN ON, and the power 
was turned off by the power switch last time, turning the power switch on makes the 
projection lamp light on without pushing the 
STANDBY/ON button ( 44).
• Use the shutdown switch (
 71) only when the projector is not turned off by 
normal procedure. NOTE
Power on/off
The projection lamp will light up and the POWER indicator will begin blinking in green. When the power is 
completely on, the indicator will stop blinking and light in steady green.
To display the picture, select an input signal according to the section "Selecting an input signal" ( 17,18).

►A strong light is emitted when the projector’s power is on. Do 
not look into the lens of the projector or look inside of the projector through any 
of the projector’s openings.
►Do not touch around the lamp cover and the exhaust vents during use or just 
after use, since it is too hot. WARNING

1.Press the STANDBY/ON button on the projector or the remote control.
The message "Power off?" will appear on the screen for about 5 seconds.
Turning off  the power
2.Press the STANDBY/ON button on the projector or the remote control again while 
the message appears.  
The projector lamp will go off, and the POWER indicator will begin blinking in orange. 
Then the POWER indicator will stop blinking and light in steady orange when the 
lamp cooling is complete.
3.Make sure that the POWER indicator lights in steady orange, and set the 
power switch to the OFF position (marked “
O”).  
The 
POWER indicator will go off. Attach the lens cover.
Do not turn the projector on for 10 minutes or more after turning it off. Turning the projector 
on again too soon could shorten the lifetime of some consumable parts of the projector.
STANDBY/ON button
POWER indicator

Power 
switch 
						

							
17

Operating

BLANKLASER
ASPECT
PUSH  ENTER
 PAGE UP
LASER
INDICATOR
MY SOURCE/
DOC.CAMERA
SEARCH
STANDBY/ON
VIDEORGB
PAGE DOWN
ESCMENU RESET
POSITION AUTOPbyP
MAGNIFYON
OFFMY BUTTON1
2VOLUME+
-
FREEZE KEYSTONE MUTE

BLANK LASER
ASPECT
PUSH  ENTER
 PAGE UP
LASER
INDICATOR
MY SOURCE/
DOC.CAMERA
SEARCH
STANDBY/ON
VIDEORGB
PAGE DOWN
ESCMENU RESET
POSITION AUTOPbyP
MAGNIFYON
OFFMY BUTTON1
2VOLUME+
-
FREEZE KEYSTONE MUTE

Temporarily muting the sound

BLANK LASER
ASPECT
PUSH  ENTER
 PAGE UP
LASER
INDICATOR
MY SOURCE/
DOC.CAMERA
SEARCH
STANDBY/ON
VIDEORGB
PAGE DOWN
ESCMENU RESET
POSITION AUTOPbyP
MAGNIFYON
OFFMY BUTTON1
2VOLUME+
-
FREEZE KEYSTONE MUTE

           RGB 1           RGB 2          HDMI   
          
VIDEO  S-VIDEO  COMPONENT (Y, CB/PB, CR/PR)
Operating
1.Use the VOLUME + / VOLUME - buttons to adjust the 
volume.
A dialog will appear on the screen to aid you in adjusting the 
volume.If you do not do anything, the dialog will automatically 
disappear after a few seconds.
Adjusting the volume
●   When 
 is selected for current picture input port, the volume adjustment is 
disabled. Please see AUDIO item of AUDIO Menu (
38).
● 
 
When the projector is in the standby mode, the volume can be adjusted if 

 is 
not selected for the AUDIO OUT STANDBY of AUDIO (
38). 
1.Press MUTE button on the remote control.
A dialog will appear on the screen indicating that you have 
muted the sound.
To restore the sound, press the 
MUTE, VOLUME + or 
VOLUME - button. Even if you do not do anything, the dialog 
will automatically disappear after a few seconds.
1.Press the 
INPUT  button on the projector.  
Each time you press the button, the projector switches its 
input from the current port as below.
Selecting an input signal

          RGB 1   RGB 2  HDMI 
1.Press the RGB button on the remote control to select an 
input port for the RGB signal. 
Each time you press the button, the projector switches its 
RGB input from the current port as below.

●  While TURN ON is selected for AUTO SEARCH item in OPTION Menu, 
the projector will keep checking every port sequentially till aninput signal 
is detected
 (44). If RGB button is pushed when VIDEO, S-VIDEO or 
COMPONENT  port is selected, the projector will check RGB1 port first. 
(continued on next page)

●  When 
 is selected for current picture input port, the sound is always muted. 
Please see AUDIO item of AUDIO Menu
 (38).
● 
 When the sound is muted while a signal from VIDEO(NTSC), 
S-VIDEO(NTSC) or COMPONENT(480i@60) port is selected, the C.C. 
(Closed Caption) is automatically activated if the DISPLAY item of the C.C. 
Menu is set to AUTO and the input signal supports the C.C. feature (
 62). 
						

							
18

Operating

BLANKLASER
ASPECT
PUSH  ENTER
 PAGE UP
LASER
INDICATOR
MY SOURCE/
DOC.CAMERA
SEARCH
STANDBY/ON
VIDEORGB
PAGE DOWN
ESCMENU RESET
POSITION AUTOPbyP
MAGNIFYON
OFFMY BUTTON1
2VOLUME+
-
FREEZE KEYSTONE MUTE

BLANK LASER
ASPECT
PUSH  ENTER
 PAGE UP
LASER
INDICATOR
MY SOURCE/
DOC.CAMERA
SEARCH
STANDBY/ON
VIDEORGB
PAGE DOWN
ESCMENU RESET
POSITION AUTOPbyP
MAGNIFYON
OFFMY BUTTON1
2VOLUME+
-
FREEZE KEYSTONE MUTE

1.Press the VIDEO button on the remote control to select an 
input for video signal.   
Each time you press the button, the projector switches its 
video input port as below. 
Selecting an input signal (continued)
● While TURN ON is selected for AUTO SEARCH item in OPTION Menu, the 
projector will keep checking every port sequentially till an input signal is detected 
(

44). If VIDEO button is pushed when RGB 1 or RGB 2 port is selected, the 
projector will check 
COMPONENT  port first.
1.Press the ASPECT button on the remote control.   
Each time you press the button, the projector switches the mode for aspect 
ratio in turn. 
Selecting an aspect ratio
● The NORMAL mode keeps the original aspect ratio of the signal.
COMPONENT (Y, CB/PB, CR/PR)  S-VIDEO   VIDEO
    

BLANK LASER
ASPEC T
 ESC  MENU  RESET
   
  POSITION  AUTO 
 
 M AGNIFY 
MY BUTTO N VOLUME
  ON  1
    MUTE
  OFF  2
  FREEZE  KEYSTONE  SEARCH
 
PUSH ENTER
 PAGE UP   PAGE DOWN
 STANDBY/ON VIDEO  RGB
LASER
INDICATOR

1.Press the SEARCH button on the remote control.
The projector will start to check its input ports in order to find 
any input signals.
When an input is found, the projector will stop searching 
and display the image. If no signal is found, the projector will 
return to the state selected before the operation.
Searching an input signal
RGB 1  RGB 2  HDMI   COMPONENT (Y, CB/PB, CR/PR)  S-VIDEO  VIDEO 
     

    For an RGB signal
 
NORMAL  4:3  16:9  16:10  REAL  
  

    For an HDMI signal
 
NORMAL  4:3  16:9  16:10  14:9  REAL  
  

    For a video signal, s-video signal or component video signal
 
4:3  16:9  16:10  14:9  REAL  
  

    For no signal 
 
16:10 (fixed)

BLANK LASER
ASPECT
PUSH  ENTER
 PAGE UP
LASER
INDICATOR
MY SOURCE/
DOC.CAMERA
SEARCH
STANDBY/ON
VIDEORGB
PAGE DOWN
ESCMENU RESET
POSITION AUTOPbyP
MAGNIFYON
OFFMY BUTTON1
2VOLUME+
-
FREEZE KEYSTONE MUTE

1.Press the MY SOURCE / DOC. CAMERA  button on the 
remote control. The input signal will be changed into the 
signal you set as MY SOURCE(
 46).
●  This function also can use for document camera. Select the input port that 
connected the document camera.  
						

							
19

Operating

BLANKLASER
ASPECT
PUSH  ENTER
 PAGE UP
LASER
INDICATOR
MY SOURCE/
DOC.CAMERA
SEARCH
STANDBY/ON
VIDEORGB
PAGE DOWN
ESCMENU RESET
POSITION AUTOPbyP
MAGNIFYON
OFFMY BUTTON1
2VOLUME+
-
FREEZE KEYSTONE MUTE

• When the vertical lens shift 
is adjusted, it is recommended to shift 
the picture upward. NOTE
1.Use the zoom ring to adjust the screen size.
Adjusting the zoom and focus
2.Use the focus ring to focus the picture.

1/2
1/10
1/10

Zoom ring Focus ring
Top
1.Use the vertical lens shift dial to shift 
the picture upward or downward.
Adjusting the lens shift
2.Use the horizontal lens shift dial to 
shift the picture left or right.
1.Press the AUTO button on the remote control.
Pressing this button performs the following.
Using the automatic adjustment feature
   For an RGB signal  
The vertical position, the horizontal position and the 
horizontal phase will be automatically adjusted.  
Make sure that the application window is set to its 
maximum size prior to attempting to use this feature. 
A dark picture may still be incorrectly adjusted. Use a 
bright picture when adjusting.
 
 For a video signal and s-video signal  
The video format best suited for the respective input signal will be selected 
automatically. This function is available only when the AUTO is selected for 
the VIDEO FORMAT item in the INPUT Menu (
 33). The vertical position 
and horizontal position will be automatically set to the default.
 
 
For a component video signal  
The vertical position, horizontal position and horizontal phase will be 
automatically set to the default.
● 
 
The automatic adjustment operation requires approx. 10 seconds.  Also 
please note that it may not function correctly with some input. When this 
function is performed for a video signal, a certain extra such as a line may 
appear outside a picture.
● 
 
The items adjusted by this function may vary when the FINE or DISABLE is 
selected for the AUTO ADJUST item of the SERVICE item in the OPTION 
Menu (
 47).
UP
DOWN
LEFT RIGHT
Lens shift cover 
						

							
20

Operating

BLANKLASER
ASPECT
PUSH  ENTER
 PAGE UP
LASER
INDICATOR
MY SOURCE/
DOC.CAMERA
SEARCH
STANDBY/ON
VIDEORGB
PAGE DOWN
ESCMENU RESET
POSITION AUTOPbyP
MAGNIFYON
OFFMY BUTTON1
2VOLUME+
-
FREEZE KEYSTONE MUTE

BLANK LASER
ASPECT
PUSH  ENTER
 PAGE UP
LASER
INDICATOR
MY SOURCE/
DOC.CAMERA
SEARCH
STANDBY/ON
VIDEORGB
PAGE DOWN
ESCMENU RESET
POSITION AUTOPbyP
MAGNIFYON
OFFMY BUTTON1
2VOLUME+
-
FREEZE KEYSTONE MUTE

1.Press the POSITION button on the remote control when no 
menu is indicated.  
The “POSITION” indication will appear on the screen.
Adjusting the position
2.Use the ▲/▼/◄/► cursor buttons to adjust the picture position.
When you want to reset the operation, press the RESET  
button on the remote control during the operation.
To complete this operation, press the 
POSITION  button 
again. Even if you do not do anything, the dialog will 
automatically disappear after a few seconds.
● 
 
When this function is performed on a video signal, s-video signal or component 
video signal, some image such as an extra-line may appear at outside of the picture.
●   When this function is performing on a Video signal, S-Video signal, or component 
signal of 480i@60 or 576i@50 input the range of this adjustment depends on the 
OVER SCAN in IMAGE Menu (
 30). It is not possible to adjust when the OVER 
SCAN is set to 10.

1.Press the 
KEYSTONE button on the remote 
control. A dialog will appear on the screen 
to aid you in correcting the distortion.
Correcting the keystone distortions
2.Use the ▲/▼ cursor buttons to select AUTO or MANUAL 
operation, and press the ► button to perform the following.
●   The adjustable range of this function will vary among inputs. For some input, this 
function may not work well.
● 
 When V:INVERT or H&V:INVERT is selected to the MIRROR item in the SETUP 
Menu, if the projector screen is inclined or angled downward, this function may 
not work correctly.
● 
 When the zoom adjustment is set to the TELE (telephoto focus), this function 
may be excessive. This function should be used when the zoom adjustment is 
set to the full WIDE (wide-angle focus) whenever possible.
● 
 When the projector is placed on the level (about ±3°), this function may not work.
● 
 
When the projector is inclined to near ±30 degree or over, this function may not work well.
●  When the vertical lens shift is not set fully upward (not set fully downward for the 
optional lens type FL-601 only (
 47)), this function may not work well.
● 
 
When the horizontal lens shift is not set to the center, this function may not work well.
● This function will be unavailable when Transition Detector is on ( 53).
1)  AUTO executes automatic vertical keystone correction. 
2)  
 MANUAL displays a dialog for keystone correction.   
Use the ◄/► cursor buttons to select the direction to 
correct (

 or 
) then use the ▲/▼ buttons for adjustment.
To close the dialog and complete this operation, press the 

KEYSTONE button again. Even if you don’t do anything, the 
dialog will automatically disappear after a few seconds.