Dukane Imagepro 8949h Projector Users Manual

							
31

IMAGE Menu

IMAGE Menu (continued)

ItemDescription
H PHASE
Using the ▲/▼ buttons adjusts the horizontal phase to eliminate flicker.
Right  ó Left
• This item can be selected only for an RGB signal or a component 
video signal. (except 480i@60, 576i@50, SCART RGB input. )
H SIZE Using the ▲/▼ buttons adjusts the horizontal size.
Large  ó Small
• This item can be selected only for an RGB signal.
• When this adjustment is excessive, the picture may not be 
displayed correctly. In such a case, please reset the adjustment 
by pressing the 
RESET  button on the remote control during this 
operation.
AUTO ADJUST  EXECUTE Selecting this item performs the automatic adjustment feature.
For an RGB signal
The vertical position, the horizontal position and the horizontal 
phase will be automatically adjusted. 
Make sure that the application window is set to its maximum size 
prior to attempting to use this feature. A dark picture may still be 
incorrectly adjusted. Use a bright picture when adjusting.
For a video signal and s-video signal
The video format best suited for the respective input signal will 
be selected automatically. This function is available only when 
the AUTO is selected for the VIDEO FORMAT item in the INPUT 
Menu (

33). The vertical position and horizontal position will be 
automatically set to the default.
For a component video signal
The vertical position, horizontal position and horizontal phase will 
be automatically set to the default.
• The automatic adjustment operation requires approx. 10 seconds. 
Also please note that it may not function correctly with some input. 
When this function is performed for a video signal, a certain extra 
such as a line may appear outside a picture.
• The items adjusted by this function may vary when the FINE or 
DISABLE is selected for the AUTO ADJUST item of the SERVICE 
item in the OPTION Menu (
 47). 
						

							
32

INPUT Menu
INPUT Menu
From the INPUT Menu, items shown in the table below 
can be performed.
Select an item using the ▲/▼ cursor buttons on the 
projector or remote control, and press the ► cursor 
button on the projector or remote control, or 

ENTER 
button on the remote control to execute the item. Then 
perform it according to the following table.

Item Description
PROGRESSIVE Using the ▲/▼ buttons switches the progress mode.
TV  ó FILM 
ó TURN OFF
  

• This function is performed only for an interlaced signal at 
the VIDEO or S-VIDEO input, and for 480i@60, 576i@50 or 
1080i@50/60 signal at the COMPONENT  or 
HDMI input.
• When TV or FILM is selected, the screen image will be sharp. 
FILM adapts to the 2-3 Pull-Down conversion system. But these 
may cause a certain defect (for example, jagged line) of the picture 
for a quick moving object. In such a case, please select TURN OFF, 
even though the screen image may lose the sharpness.
VIDEO NR Using the ▲/▼ buttons switches the noise reduction mode.
HIGH  ó MID 
ó LOW
   

• This function is performed only for the VIDEO or S-VIDEO 
input, and for 480i@60, 576i@50 or 1080i@50/60 signal at the 
COMPONENT  or 
HDMI input.
• When this function is excessive, it may cause a certain 
degradation of the picture. 
3D-YCS Using the ▲/▼ buttons switches the 3D-YCS mode.
STILL  ó MOVIE 
ó TURN OFF
     

• This function performs only at a VIDEO input of NTSC, and PAL.
• MOVIE is the mode for images with a lot of motions like movies, 
and STILL is the mode for images with few motions or completely 
still ones like slides.
COLOR SPACE Using the ▲/▼ buttons switches the mode for color space.
AUTO  ó RGB 
ó SMPTE240 
ó REC709 
ó REC601
      

• This item can be selected only for an RGB signal or a component 
video signal (except  480i@60, 576i@50 and SCART RGB).
• The AUTO mode automatically selects the optimum mode.
• The AUTO operation may not work well at some signals. In such a 
case, it might be good to select a suitable mode except AUTO.
(continued on next page) 
						

							
33

INPUT Menu

INPUT Menu (continued)

ItemDescription
COMPONENT Using the ▲/▼ buttons switches the function of the 
COMPONENT
 (Y, CB
/PB, Cr
/Pr) port.
COMPONENT  ó SCART RGB
When the SCART RGB is selected, the 
COMPONENT  (Y, CB
/PB, Cr
/Pr) and VIDEO ports will function as a SCART RGB port. 
A SCART adapter or SCART cable is required for a SCART RGB 
input to the projector. For details, contact your dealer.
VIDEO FORMAT Set the video format for the 
S-VIDEO port and VIDEO port.
(1) Use the ◄/► buttons to select the input port.
(2) Using the ▲/▼ buttons switches the mode 
for video format. AUTO   ó  NTSC  
ó  PAL  
ó  SECAM
      N-PAL  ó M-PAL 
ó NTSC4.43 
• This item is performed only for a video signal 
from the 
VIDEO port or the S-VIDEO port.
• The AUTO mode automatically selects the optimum mode.
• The AUTO operation may not work well for some signals. If the 
picture becomes unstable (e.g. an irregular picture, lack of color), 
please select the mode according to the input signal.
HDMI Using the ▲/▼ cursor buttons changes the HDMI signal mode.
AUTO  ó NORMAL 
ó ENHANCED
     

Feature
AUTO Selecting the optimum mode automatically.
NORMAL Suitable for DVD signals (16-235)
ENHANCED Suitable for VGA signals (0-255)
• If the contrast of the screen image is too strong or too weak, try 
finding a more suitable mode.

VIDEO
CONTROL
AUDIO IN 
1
AUDIO IN  2
REMOTE 
CONTROL
   
S-VIDEO
AUDI
O
OUT  R   L R   L
   AUDIO IN 3    AUDIO IN  4
RGB
 OUT RGB1
RGB2 M1-DCB/PBY
CR/PR
LAN
SCART OUT

Video GBR
(continued on next page) 
						

							
34

INPUT Menu

INPUT Menu (continued)

ItemDescription
FRAME LOCK Set the frame lock function on/off for each port.
(1) Use the ▲/▼ buttons to select one of 
following ports.
QUIT  ó RGB1 
ó RGB2 
ó HDMI
    

(2) Use the ◄/► buttons to turns the frame 
lock function on/off .
TURN ON  ó TURN OFF
• This item can be performed only on a signal   
with a vertical frequency of 50 to 60 Hz.
• When the TURN ON is selected, moving pictures are displayed 
more smoothly.
• This function may cause a certain degradation of the picture. In 
such a case, please select the TURN OFF.
RGB IN Set the RGB input signal type for the 
RGB port.
(1) Use the ◄/► buttons to select the 
RGB 
port to be set.
RGB1  ó RGB2
(2) Use the ▲/▼ buttons to select the RGB 
input signal type. AUTO  ó SYNC ON G OFF
• Selecting the AUTO mode allows you to input a sync on G signal 
or component signal from the port.
• In the AUTO mode, the picture may be distorted with certain 
input signals. In such a case, remove the signal connector so that 
no signal is received and select the SYNC ON G OFF, and then 
reconnect the signal.
(continued on next page) 
						

							
35

INPUT Menu

INPUT Menu (continued)

ItemDescription
RESOLUTION The resolution for the 
RGB1 and RGB2 input signals can be set on 
this projector.
(1) In the INPUT Menu select the RESOLUTION using the ▲/▼ buttons and 
press the ► button.
The RESOLUTION menu will be displayed.
(2)  In the RESOLUTION menu select the 
resolution you wish to display using the ▲/▼ 
buttons. 
Selecting AUTO will set a resolution 
appropriate to the input signal.
(3) Pressing the ► or 

ENTER button when 
selecting a STANDARD resolution will 
automatically adjust the horizontal and 
vertical positions, clock phase and horizontal 
size.
 The INPUT-INFORMATION- dialog (
 48) 
will be displayed.
(4) To set a custom resolution use the   
▲/▼ buttons to select the CUSTOM and 
the CUSTOM RESOLUTION BOX will be 
displayed. Set the horizontal (HORZ) and 
vertical (VERT) resolutions using the   
▲/▼/◄/► buttons.
It is not guaranteed to work this function 
properly on any resolutions.
(5) To save the setting place the cursor on the 
right-most digit and press the ► button.
The horizontal and vertical positions, clock 
phase and horizontal size will be automatically 
adjusted.
After the INPUT-INFORMATION- (
 48) 
dialog has displayed for about 10 seconds the 
screen will return to the RESOLUTION menu 
displaying the changed resolution.
(6) To revert back to the previous resolution 
without saving changes place the cursor on 
the left-most digit and press the ◄ button.
The screen will then return to the RESOLUTION menu displaying the 
previous resolution.
• For some pictures, this function may not work well.
RESOLUTION menu
CUSTOM RESOLUTION  BOX 
						

							
36

SETUP Menu
SETUP Menu
From the SETUP Menu, items shown in the table below 
can be performed.
Select an item using the ▲/▼ cursor buttons on the 
projector or remote control, and press the ► cursor button 
on the projector or remote control, or the 

ENTER button 
on the remote control to execute the item. Then perform it 
according to the following table.

Item Description
AUTO 
KEYSTONE 

EXECUTE Selecting this item performs the Automatic keystone distortion 
correction. Projector automatically corrects vertical keystone 
distortion due to the (forward/backward) setup angle by itself.
This function will be executed only once when selected in the menu. 
When the slant of the projector is changed, execute this function 
again.
• The adjustable range of this function will vary among inputs. For 
some input, this function may not work well.
• When V:INVERT or H&V:INVERT is selected to the MIRROR item 
in the SETUP Menu, if the projector screen is inclined or angled 
downward, this function may not work correctly.
• When the zoom adjustment is set to the TELE (telephoto focus), 
this function may be excessive. This function should be used when 
the zoom adjustment is set to the full WIDE (wide-angle focus) 
whenever possible.
• When the projector is placed on the level (about ±3°), this function 
may not work.
• When the projector is inclined to near ±30 degree or over, this 
function may not work well.
• When the vertical lens shift is not set fully upward (not set fully 
downward for the optional lens type FL-601 only 
(
47)), this 
function may not work well.
• When the horizontal lens shift is not set to the center, this function 
may not work well.
• This function will be unavailable when the Transition Detector is 
on (
 53).
KEYSTONE 

Using the ▲/▼ buttons corrects the vertical keystone distortion. Shrink the top of the image  ó Shrink the bottom of the image
• The adjustable range of this function will vary among inputs. For 
some input, this function may not work well.
• When the horizontal lens shift is not set to the center, this function 
may not work well.
• This function will be unavailable when the Transition Detector is 
on (
 53).
(continued on next page) 
						

							
37

SETUP Menu

SETUP Menu (continued)

ItemDescription
KEYSTONE 

Using the ▲/▼ buttons corrects the horizontal keystone distortion. Shrink the right of the image  ó Shrink the left of the image
• The adjustable range of this function will vary among inputs. For 
some input, this function may not work well.
• When the zoom adjustment is set to the TELE (telephoto focus), 
this function may be excessive. This function should be used when 
the zoom adjustment is set to the full WIDE (wide-angle focus) 
whenever possible.
• When the vertical lens shift is not set fully upward (not set fully 
downward for the optional lens type FL-601 only  (
47)), this 
function may not work well.
• This function will be unavailable when the Transition Detector is 
on (
 53).
WHISPER Using the ▲/▼ buttons turns off/on the whisper mode.
NORMAL  ó WHISPER
• When the WHISPER is selected, acoustic noise and screen 
brightness are reduced.
MIRROR Using the ▲/▼ buttons switches the mode for mirror status.

NORMAL 
ó H:INVERT 
ó V:INVERT 
ó H&V:INVERT
 

If the  Transition Detector  is TURN ON and MIRROR status is 
changed,  Transition Detector  Alarm (
53) will be displayed when 
projector is restarted after the power switch is turned off.
MONITOR OUT The combination of a picture shown on screen and output from the
MONITOR OUT
 port can be arranged in the menu.
The picture coming into the port selected in the (2) is output to the
MONITOR OUT  port while an image from the port chosen in the (1) 
is on screen.
(1) Choose a picture input port using ▲/▼ buttons.
    

QUIT  ó  RGB1 
ó   RGB2 
ó   HDMI 
STANDBY 
ó VIDEO 
ó  S-VIDEO 
ó  COMPONENT(Y, CB/PB, CR/PR)
• Choose STANDBY, to select the output signal from the MONITOROUT
 port in the standby mode.
• While QUIT is selected, pressing the ◄ 
button returns to the previous menu.
(2) Select one of the 
RGB ports using ◄/► 
buttons.
        RGB1 
ó  RGB2 ó OFF
• OFF disables the 
MONITOR OUT  port.
(continued on next page) 
						

							
38

AUDIO Menu
AUDIO Menu
From the AUDIO Menu, items shown in the table below 
can be performed.
Select an item using the ▲/▼ cursor buttons on the 
projector or remote control, and press the ► cursor button 
on the projector or remote control, or 

ENTER button on 
the remote control to execute the item. Then perform it 
according to the following table.

Item Description
VOLUME Using the ▲/▼ buttons adjusts the volume.
High  ó Low
TREBLE Using the ▲/▼ buttons adjusts the treble level.
High  ó Low
BASS Using the ▲/▼ buttons adjusts the bass level.
 
High  ó Low
SRS WOW Using the ▲/▼ buttons switches the mode for SRS WOW mode. 
HIGH  ó MID 
ó OFF
    

• SRS WOW ® accomplishes this by providing a panoramic three-
dimensional audio image that extends the sound field in both the 
horizontal and vertical planes, and lowers the perceived bass 
response well beyond the low frequency limitations of the drivers. 
Adjust it depending on the user's preference.
SPEAKER Using the ▲/▼ buttons turns the speaker function on/off. 
TURN ON  ó TURN OFF
• When the TURN ON is selected the built-in speaker works.
AUDIO Allocates the audio ports.
(1) Choose a picture input port using the ▲/▼ buttons.

 QUIT 
ó  RGB1 
ó  RGB2 ó HDMI 
ó  COMPONENT
AUDIO OUT STANDBY 
ó VIDEO 
ó  S-VIDEO
(2) Select the audio port to be interlocked with 
the input port using the ◄/► buttons.
1 ó  2 
ó 3 
ó 4 
ó 

 
ó  H
• H is abbreviation of HDMI.
• H can be selected for 

HDMI port only. When H 
is selected, the audio signal to 
HDMI port will be 
output if HDMI is chosen as a display source.
• 

 disables the audio output.
• When 
 is selected to VIDEO, S-VIDEO or COMPONENT  port, the C.C. (Closed 
Caption) is automatically activated, if the C.C. is set to AUTO in the DISPLAY Menu 
of the C.C. Menu and the signal from the input port supports the C.C. feature (
 62).
HDMI AUDIO The HDMI AUDIO is set to 1 as default. In case the HDMI audio 
does not work well, try 2.
1 ó  2 

• The speaker sound may distorted or the case may be trembling when 
the volume is too high or treble/bass is emphasized or WOW is activated. In that 
case, make the volume reduced, bass/treble low or WOW effect to be weakend.NOTE 
						

							
39

SCREEN Menu
SCREEN Menu
From the SCREEN Menu, items shown in the table below 
can be performed.
Select an item using the ▲/▼ cursor buttons on the 
projector or remote control, and press the ► cursor button 
on the projector or remote control, or 

ENTER button on 
the remote control to execute the item. Then perform it 
according to the following table.

Item Description
LANGUAGE
Using the ▲/▼ buttons switches the OSD (On Screen Display) language.

�
TÜRKÇE �
POLSKI �
SUOMI �
ENGLISH � FRANÇAIS � DEUTSCH � ESP
AÑOL � ITALIANO
�
NORSK �
NEDERLANDS �
POR TUGUÊS
�
РУ ССКИЙ  � SVENSKA  � ¿—µ � 4P¨
[ � 1T
[ � ãÄ.† 

MENU POSITION Using the ▲/▼/◄/► buttons adjusts the menu position.
To quit the operation, press the MENU button on the remote control 
or keep no operation for about 10 seconds.
BLANK Using the ▲/▼ buttons switches the mode for the blank screen.
The blank screen is a screen for the temporarily blanking feature
 
(
22). It is displayed by pressing the BLANK button on the remote 
control.
MyScreen  ó ORIGINAL 
ó BLUE 
ó WHITE 
ó BLACK
  

Feature
MyScreen Screen can be registered by the MyScreen item 
(
41).
ORIGINAL Screen preset as the standard screen.
BLUE, WHITE, 
BLACK Plain screens in each color.
• To avoid remaining as an afterimage, the MyScreen or ORIGINAL 
screen will change to the plain black screen after several minutes.

(continued on next page) 
						

							
40

SCREEN Menu

SCREEN Menu (continued)

ItemDescription
START UP Using the ▲/▼ buttons switches the mode for the start-up screen.
The start-up screen is a screen displayed when no signal or an 
unsuitable signal is detected.
MyScreen  ó ORIGINAL 
ó TURN OFF
    

Feature
MyScreen Screen can be registered by the MyScreen item 
(
41).
ORIGINAL Screen preset as the standard screen.
TURN OFF Plain black screen.
• To avoid remaining as an afterimage, the MyScreen or ORIGINAL 
screen will change to the BLANK screen  (
39) after several 
minutes. If also the BLANK screen is the MyScreen or ORIGINAL, 
the plain black screen is instead used.
• When the TURN ON is selected to the MyScreen PASSWORD of 
SECURITY item in OPTION Menu (
 50), the START UP is fixed to 
MyScreen.
(continued on next page)