Dukane Imagepro 8943 Portable Lcd Projector Users Manual

							
9

IMAGE Menu
IMAGE Menu
ItemDescription
ASPECT
Using the ▲/▼ buttons switches the mode for aspect ratio. For an RGB signalNORMAL ó 4:3 ó    6:9 ó SMALL         
For an M1-D signalNORMAL ó 4:3 ó   6:9 ó   4:9 ó SMALL         
For a Video signal, S-video signal or Component video signal4:3 ó   6:9 ó   4:9 ó SMALL     
For no signal4:3 (fixed)• The NORMAL mode keeps the original aspect ratio of the signal.
OVER SCAN
Using the ▲/▼ buttons adjusts the over-scan ratio.Large (It reduces picture) ó Small (It magnifies picture)• This item can be selected only for a video, s-video and component signal.• When this adjustment is too large, certain degradation may appear at the frame area of the picture. In such a case, please adjust small.
V POSITION
Using the ▲/▼ buttons adjusts the vertical position.Up ó Down• Over-adjusting the vertical position may cause noise to appear on the screen. If this occurs please reset the vertical position to the \
default setting. Pressing the RESET button when the V POSITION is selected will reset the V POSITION to the default setting.• When this function is performed on a video signal, s-video signal, \
or component video signal of 5
 5i (480i) or 6  5i (576i), the range of 
this adjustment depends on the OVER SCAN (above) setting. It is 
not possible to adjust when the OVER SCAN is set to 
 0.
H POSITION
Using the ▲/▼ buttons adjusts the horizontal position.Left ó Right• Over-adjusting the horizontal position may cause noise to appear on the screen. If this occurs please reset the horizontal position to th\
e default setting. Pressing the RESET button when the H POSITION is selected will reset the H POSITION to the default setting.• When this function is performed on a video signal, s-video signal, \
or component video signal of 5  5i (480i) or 6  5i (576i), the range of 
this adjustment depends on the OVER SCAN (above) setting. It is 
not possible to adjust when the OVER SCAN is set to 
 0.
From the IMAGE menu, items shown in the table below 
can be performed.
Select an item using the ▲/▼ cursor buttons on the 
projector or remote control, and press the ► cursor button 
on the projector or remote control, or ENTER button on 
the remote control to execute the item. Then perform it 
according to the following table.
/07=4)$?
+/#)
2+%674
5.%6
#761#&,756:%76
#52%61845%#0
*2*#5*5+
						

							
30

IMAGE Menu
ItemDescription
H PHASE
Using the ▲/▼ buttons adjusts the horizontal phase to eliminate flicker.
Right ó Left
• This item can be selected only for an RGB signal or a component 
video signal. (except 5
 5i (480i), 6  5i (576i), SCART RGB)
H SIZE
Using the ▲/▼ buttons adjusts the horizontal size.
Large ó Small
• This item can be selected only for an RGB signal.
• When this adjustment is excessive, the picture may not be displayed correctly. In such a case, please reset the adjustment by pressing the RESET button on the remote control during this operation.
AUTO ADJUST EXECUTE
Selecting this item performs the automatic adjustment feature.
For an RGB signalThe vertical position, the horizontal position, the horizontal phase and the horizontal size will be automatically set to default. And the aspect ratio will be automatically selected. Make sure that the application window is set to its maximum size prior to attempting to use this feature. A dark picture may still be incorrectly adjusted. Use a bright picture when adjusting.
For an M1-D signalThe aspect ratio will be automatically set to default.
For a Video signal or S-video signalThe video format best suited for the respective input signal will be selected automatically.This function is available only when the AUTO mode is selected to the VIDEO FORMAT item in INPUT menu. For a component video signal, the signal type is identified automatically independently of this function.For a Video signal, S-video signal or Component video signalThe vertical position, horizontal position and aspect ratio will be automatically set to default.
For a Component video signalThe horizontal phase will be automatically set to default.
• The automatic adjustment operation requires about   0 seconds. Also please note that it may not function correctly with some input.
IMAGE Menu (continued) 
						

							
3

INPUT Menu
INPUT Menu
ItemDescription
PROGRESSIVE
Using the ▲/▼ buttons switches the progress mode.
TV ó FILM ó TURN OFF
• This function is performed only for an interlaced signal of a VIDEO 
input, an S-VIDEO input or COMPONENT VIDEO input of 5  5i 
(480i), 6
 5i (576i) or   5i (  080i) signal.
• When TV or FILM is selected, the screen image will be sharp. 
FILM adapts to the   -3 Pull-Down conversion system. But these 
may cause a certain defect (for example, jagged line) of the picture for a quick moving object. In such a case, please select TURN OFF, even though the screen image may lose the sharpness.
VIDEO NR
Using the ▲/▼ buttons switches the noise reduction mode.
HIGH ó MID ó LOW• This function performs only at a VIDEO input, an S-VIDEO or 
COMPONENT VIDEO input of 5  5i(480i), 6  5i(576i) or   5i (  080i) 
signal. 
• When this function is excessive, it may cause a certain degradation of the picture. 
3D-YCS
Using the ▲/▼ buttons switches the 3D-YCS mode.
STILL ó MOVIE ó TURN OFF
• This function performs only at a VIDEO input of NTSC, and PAL.
• MOVIE is the mode for images with a lot of motions like movies, and STILL is the mode for images with few motions or completely still ones like slides.
COLOR SPACE
Using the ▲/▼ buttons switches the mode for color space. 
AUTO ó RGB ó SMPTE  40 ó REC709 ó REC60       
• This item can be selected only for an RGB signal or a component 
video signal (except 5  5i (480i), 6  5i (576i) and SCART RGB).
• The AUTO mode automatically selects the optimum mode. 
• The AUTO operation may not work well at some signals. In such a case, it might be good to select a suitable mode except AUTO.
From the INPUT menu, items shown in the table below can 
be performed.
Select an item using the ▲/▼ cursor buttons on the 
projector or remote control, and press the ► cursor button 
on the projector or remote control, or ENTER button on 
the remote control to execute the item. Then perform it 
according to the following table.
/07=4)$?5.%6
8+&1(14/#6#761
%1.1452#%#761&;%556+..
(4#/.1%-674010
451.76+104)$+0
/&014/#.
%1/21006%1/21006
241)455+8688+&104/+&+/#)2+%674
5672+0276
5%40126+10
#7&+1
06914-#5;/07
(continued on next page) 
						

							
3

ItemDescription
COMPONENT
Using the ▲/▼ buttons switches the function of the COMPONENT (Y, Cb/Pb, Cr/Pr) port.
COMPONENT ó SCART RGB 
When the SCART RGB is selected, the COMPONENT (Y, Cb/Pb, Cr/Pr) and VIDEO ports will function as a SCART RGB port. A SCART adapter or SCART cable is required for a SCART RGB input to the projector. For details, contact your dealer.
VIDEO FORMAT
Set the video format for the s-video port and video port.
(
 ) Use th
e ◄/► buttons to select the input port.
(2) Using the ▲/▼ buttons switches the mode for video format.
AUTO  ó  NTSC  ó  PAL  ó  SECAM 
      N-PAL ó M-PAL ó NTSC4.43 
• This item is performed only for a video signal from the VIDEO port or the S-VIDEO port. 
• The AUTO mode automatically selects the optimum mode.
• The AUTO operation may not work well for some signals. If the picture becomes unstable (e.g. an irregular picture, lack of color), please select the mode according to the input signal.
M1-D
Using the ▲/▼ cursor buttons changes the M1-D signal mode.
NORMAL ó ENHANCED
Feature
NORMAL Suitable for DVD signals (  6-  35)
ENHANCEDSuitable for VGA signals (0-  55)
• If the contrast of the screen image is too strong or too weak, try finding a more suitable mode.
INPUT Menu
INPUT Menu (continued)
8+&1(14/#658+&1#761065%2#.5%#/065%/2#.02#.
8+&1
(continued on next page)
VIDEO
CONTROL
AUDIO IN 1AUDIO IN 2
REMOTE CONTROL   S-VIDEOAUDIOOUT  R  L R  L   AUDIO IN 3   AUDIO IN 4
RGB OUTRGB1RGB2M1-DCB/PBYCR/PR
LAN
SCART OUT
VideoGBR 
						

							
33

ItemDescription
FRAME LOCK
Using the ▲/▼ buttons turns the frame lock function on/off. 
TURN ON ó TURN OFF
• This item can be performed only on an RGB signal with a vertical frequency of 50 to 60 Hz.
• When the TURN ON is selected, a moving pictures are displayed more smoothly.
• This function may cause a certain degradation of the picture. In such a case, please select the TURN OFF.
RGB IN
Set the RGB input signal type for the RGB port.
( ) Use th
e ◄/► buttons to select the RGB port to be set.
RGB   
ó RGB 
(2) Use the ▲/▼ buttons to select the RGB input signal type.
SYNC ON G ON ó SYNC ON G OFF
• Selecting the SYNC ON G ON turns the SYNC ON G mode on. The SYNC ON G mode allows reception of a sync on G signal.
• In the SYNC ON G mode, the picture may be distorted with certain input signals. In such a case, remove the signal connector so that no signal is received and turn the SYNC ON G mode off, and then reconnect the signal.
INPUT Menu
INPUT Menu (continued)
4)$+04)$
5;0%10)1((5;0%10)104)$
(continued on next page) 
						

							
34

INPUT Menu
ItemDescription
RESOLUTIONThe resolution for the RGB   and RGB   input signals can be set on 
this projector.
(1) In the INPUT menu select the RESOLUTION using the ▲/▼ buttons and press the ► button.The RESOLUTION menu will be displayed.
(
 )  In the RESOLUTION menu select the 
resolution you wish to display using the ▲/▼ buttons. Selecting AUTO will set a resolution appropriate to the input signal.
(3) Pressing the ► or ENTER button when selecting a STANDARD resolution will automatically adjust the horizontal and vertical positions, clock phase and horizontal size and automatically select an aspect ratio. The INFORMATION dialog (46)  will be displayed.
(4) To set a custom resolution use the ▲/▼ buttons to select the CUSTOM and the CUSTOM RESOLUTION BOX will be displayed. Set the horizontal (HORZ) and vertical (VERT) resolutions using the ▲/▼/◄/► buttons.Although not all resolutions are guaranteed.
(5) To save the setting place the cursor on the right-most digit and press the ► button.The horizontal and vertical positions, clock phase and horizontal size will be automatically adjusted and an aspect ratio will be automatically selected. After the INFORMATION(46) dialog has 
displayed for about 

0 seconds the screen will 
return to the RESOLUTION menu displaying the changed resolution.
(6) To revert back to the previous resolution without saving changes place the cursor on the left-most digit and press the ◄ button.The screen will then return to the RESOLUTION menu displaying the previous resolution.
• For some pictures, this function may not work well.
INPUT Menu (continued)
451.76+10
56#0&
%7561/
#761ZZZ
Z
RESOLUTION MENU
INFORMATIONRGB80x 768@ 60
INFORMATIONRGB99x 744@ 60
451.76+10
56#0&
%7561/
#761ZZZ
Z
%7561/451.76+10
56

*14
						

							
35

SETUP Menu
SETUP Menu
ItemDescription
AUTO 
KEYSTONE EXECUTE
Selecting this item performs the Automatic keystone distortion correction. Projector automatically corrects vertical keystone distortion due to the (forward/backward) setup angle by itself.
This function will be executed only once when selected in the Menu. When the slant of the projector is changed, executes this function again.
• The adjustable range of this function will vary among inputs. For some input, this function may not work well.• When V:INVERT or H&V:INVERT is selected to the MIRROR item in the SETUP menu, if the projector screen is inclined or angled downward, this function may not work correctly.• When the zoom adjustment is set to the TELE (telephoto focus), this function may be excessive. This function should be used when the zoom adjustment is set to the full WIDE (wide-angle focus) whenever possible.• When the projector is placed on the level (about ±3°), this func\
tion may not work.• When the projector is inclined to near ±30 degree or over, this function may not work well.• When the vertical lens shift is not set fully upward (not set fully dow\
nward for 
the optional lens type FL-60   only (45)), this function may not work well.• When the horizontal lens shift is not set to the center, this function may not work well.• This function will be unavailable when the Transition Detector is on (51).
KEYSTONE 
Using the ▲/▼ buttons corrects the vertical keystone distortion.
Shrink the top of the image ó Shrink the bottom of the image
• The adjustable range of this function will vary among inputs. For some input, this function may not work well.• When the vertical lens shift is not set fully upward (not set fully downward for 
the optional lens type FL-60   only (45)), this function may not work well.
• When the horizontal lens shift is not set to the center, this function may not work well.• This function will be unavailable when the Transition Detector is on (51).
KEYSTONE 
Using the ▲/▼ buttons corrects the horizontal keystone distortion.
Shrink the right of the image ó Shrink the left of the image
• The adjustable range of this function will vary among inputs. For some input, this function may not work well.• When the horizontal lens shift is not set to the center, this function may not work well.• This function will be unavailable when the Transition Detector is on (51).
From the SETUP menu, items shown in the table below 
can be performed.
Select an item using the ▲/▼ cursor buttons on the 
projector or remote control, and press the ► cursor button 
on the projector or remote control, or the ENTER button 
on the remote control to execute the item. Then perform it 
according to the following table.
/07=4)$?5.%6
-;5610
#761-;5610:%76
9*+524014/#./+4414014/#.
-;5610
+/#)2+%674
5672+0276
5%40126+10
#7&+1
06914-#5;/07
(continued on next page) 
						

							
36

SETUP Menu
SETUP Menu (continued)
ItemDescription
WHISPER
Using the ▲/▼ buttons turns off/on the whisper mode.
NORMAL ó WHISPER
• When the WHISPER is selected, acoustic noise and screen brightness are reduced.
MIRROR
Using the ▲/▼ buttons switches the mode for mirror status.
NORMAL ó H:INVERT ó V:INVERT ó H&V:INVERT 
If the Transition Detector is TURN ON and MIRROR status is changed, Transition Detector Alarm (51) will be displayed when projector is restarted after the power switch is turned off. 
						

							
37

AUDIO Menu
AUDIO Menu
ItemDescription
VOLUMEUsing the ▲/▼ buttons adjusts the volume.
High ó Low
TREBLEUsing the ▲/▼ buttons adjusts the treble level.
High ó Low
BASSUsing the ▲/▼ buttons adjusts the bass level. 
High ó Low
SRS WOW
Using the ▲/▼ buttons switches the mode for SRS WOW mode. 
HIGH ó MID ó OFF
• SRS WOW™ accomplishes this by providing a panoramic three-dimensional audio image that extends the sound field in both the horizontal and vertical planes, and lowers the perceived bass response well beyond the low frequency limitations of the drivers. Adjust it depending on the user's preference.
SPEAKER
Using the ▲/▼ buttons turns the speaker function on/off. 
TURN ON ó TURN OFF
• When the TURN ON is selected the built-in speaker works.
AUDIO
Allocates the audio ports.
(1) Choose a picture input port using the ▲/▼ buttons.           RGB 
 ó RGB ó M -D 
VIDEO ó S-VIDEO ó COMPONENT
(

) Select the audio port to be interlocked with 
the input port using the ◄/► buttons.   
ó    ó 3 ó 4 ó 
When  is selected to an input port, any audio ports do not work interlocking with the input port, and any items in AUDIO menu are invalid.
From the AUDIO menu, items shown in the table below can 
be performed.
Select an item using the ▲/▼ cursor buttons on the 
projector or remote control, and press the ► cursor button 
on the projector or remote control, or ENTER button on 
the remote control to execute the item. Then perform it 
according to the following table.
/07=4)$?
+/#)
2+%674+0276
126+1006914-#5;/07
5%40
5.%681.7/64$.$#5554591952#-4#7&+1


/+&6740105672#7&+1
#7&+1
4)$/&
37+64)$
58+&18+&1
%1/21006
 
NOTE  • The speaker sound may distorted or the case may be trembling 
when the volume is too high or treble/bass is emphasized or WOW is activ\
ated. 
In that case, make the volume reduced, bass/treble low or WOW effect to be 
weakend. 
						

							
38

SCREEN Menu
SCREEN Menu
ItemDescription
LANGUAGE
Using the ▲/▼ buttons switches the OSD (On Screen Display) language.
SUOMI ó POLSKI ó TÜRKÇE
ENGLISH ó FRANÇAIS ó DEUTSCH ó ESPAÑOL ó ITALIANO
NORSK ó NEDERLANDS ó PORTUGUÊS ó 日本語
    ó    ó        ó SVENSKA ó
MENU POSITIONUsing the ◄/►/▲/▼ buttons adjusts the menu position.To quit the operation, press the MENU button on the remote control 
or keep no operation for about 
 0 seconds.
BLANK
Using the ▲/▼ buttons switches the mode for the blank screen.
The blank screen is a screen for the temporarily blanking feature 
(22). It is displayed by pressing the BLANK button on the remote control.
MyScreen ó ORIGINAL ó BLUE ó WHITE ó BLACK  
Feature
MyScreenScreen can be registered by the MyScreen item (40).
ORIGINALScreen preset as the standard screen.
BLUE, WHITE, BLACKPlain screens in each color.
• To avoid remaining as an afterimage, the MyScreen or ORIGINAL 
screen will change to the plain black screen after several minutes.
From the SCREEN menu, items shown in the table below 
can be performed.
Select an item using the ▲/▼ cursor buttons on the 
projector or remote control, and press the ► cursor button 
on the projector or remote control, or ENTER button on 
the remote control to execute the item. Then perform it 
according to the following table.
/07=4)$?5.%6.#0)7#)0).+5*/07215+6+1056#467214+)+0#./[5ETGGP/[5ETGGP.QEM67401((
5174%0#//55#)674010
$.#0-$.#%-+/#)2+%674
5672+0276
5%40126+10
#7&+1
06914-#5;/07
(continued on next page)