Dukane Imagepro 8943 Portable Lcd Projector Users Manual

							
19

Settings
Date/Time Settings (Continued)
Click the [Apply] button to save the settings.
ItemDescription
Daylight Savings TimeClick the [ON] check box to enable daylight savings time and set the following items.
SNTP Server IP AddressConfigures the SNTP server address in IP format.
CycleConfigures the interval at which to retrieve Date and Time information from the SNTP server. (hours:minutes).
StartConfigures the date and time daylight savings time begins.
MonthConfigures the month daylight savings time begins (1~12).
WeekConfigures the week of the month daylight savings time begins (First, 2, 3, 4, Last).
DayConfigures the day of the week daylight savings time begins (Sun, Mon, Tue, Wed, Thu, Fri, Sat).
HourConfigures the hour daylight savings time begins (0 ~ 23).
MinuteConfigures the minute daylight savings time begins (0 ~ 59).
EndConfigures the date and time daylight savings time ends.
MonthConfigures the month daylight savings time ends (1 ~ 12).
WeekConfigures the week of the month daylight savings time ends (First, 2, 3, 4, Last).
DayConfigures the day of the week daylight savings time ends (Sun, Mon, Tue, Wed, Thu, Fri, Sat).
HourConfigures the hour daylight savings time ends (0 ~ 23).
MinuteConfigures the minute daylight savings time ends  (0 ~ 59).
Time differenceConfigures the time difference (hours:minutes).
Set the same time difference as the one set on your PC. If unsure, consult your network administrator.
SNTPClick the [ON] check box to retrieve Date and Time information from the SNTP server and set the following items.
• The new configuration settings are activated after restarting the network connection. 
The network connection must be restarted when the configuration settings ar e changed, The 
network connection can be restarted using [Network Restart] on the main menu.
• If you connect the projector to an existing network, consult a netw\
ork 
administrator before setting server addresses.
• To enable the SNTP function, the time difference must be set.
• The projector will retrieve DATE and TIME information from the Timeserver 
and override time settings when SNTP is enabled.
• The Internal Clock’s time may not remain accurate. Using SNTP is 
recommended to maintain accurate time.
NOTE 
						

							
20

Settings
Security Settings
ItemDescription
Administrator authorityConfigures the Administrator ID and Password.
Administrator IDConfigures the Administrator ID.The length of the text can be up to 32 alphanumeric characters.
Administrator Password
Configures the Administrator Password.The length of the text can be up to 255 alphanumeric characters.
Re-enter Administrator PasswordRe-enter the above password for verification.
Displays and configures passwords and other security settings.
User authorityConfigures the User ID and Password.
User IDConfigures the User ID.The length of the text can be up to 32 alphanumeric characters.
User PasswordConfigures the User Password.The length of the text can be up to 255 alphanumeric characters.
Re-enter User PasswordUsed to re-enter the above password for verification. 
						

							


Click the [Apply] button to save the settings.
Authentication Password
Configures the Authentication Password.The length of the text can be up to 16 alphanumeric characters.
Re-enter Authentication PasswordUsed to re-enter the above password for verification.
SNMPConfigures the community name if SNMP is used.
Community NameConfigures the community name.The length of the text can be up to 64 alphanumeric characters.
• The new configuration settings are activated after restarting the 
network connection. The network connection must be restarted when the 
configuration settings are changed. The network connection can be restarted 
using [Network Restart] on the main menu.
NOTE
ItemDescription
Network ControlConfigures the Authentication Password for the command control.
Settings
Security Settings (Continued) 
						

							


Projector Control
Projector Control
Projector Control
The items shown in the table below can be 
performed using the [Projector Control] menu.
Select an item using the up and down arrow keys 
on the PC.
Most of the items have a submenu.
Refer to the table below for details.
Controls the projector.
ItemDescription
Main
PowerTurns the power On/Off.
Input SourceSelects the input source.
Picture ModeSelects the Picture Mode setting.
Blank On/OffTurns Blank On/Off.
MuteTurns Mute On/Off.
FreezeSelects the Freeze setting.
MagnifyControls the Magnify setting.
Picture
BrightnessAdjusts the Brightness setting.
ContrastAdjusts the Contrast setting.
GammaSelects the Gamma setting.
Color TempSelects the Color Temp setting.
ColorAdjusts the Color setting.
TintAdjusts the Tint setting.
SharpnessAdjusts the Sharpness setting.
Active IrisSelects the Active Iris setting.
MyMemory RecallRecalls the MyMemory data.
MyMemory SaveSaves the MyMemory data. 
						

							
23

Projector Control
Projector Control (Continued)
ItemDescription
Image
AspectSelects the Aspect setting.
Over ScanSelects the Over Scan setting.
V PositionAdjusts the V Position.
H PositionAdjusts the H Position.
H PhaseAdjusts the H Phase.
H SizeAdjusts the H Size.
Auto AdjustPerforms Auto Adjustment.
Input
ProgressiveSelects the progressive setting.
Video NRSelects the Video NR setting.
3D-YCSSelects the 3D-YCS setting.
Color SpaceSelects the Color Space.
ComponentSelects the Component terminal setting.
C-Video FormatSelects the Video Format setting.
S-Video FormatSelects the S-Video Format setting.
M1-DSelects the M1-D setting.
Frame LockTurns Frame Lock On/Off.
RGB in-1Selects the RGB input signal type.
RGB in-2Selects the RGB input signal type.
Setup
Aoto Keystone ExecutePerforms the Automatic keystone distortion correction.
Keystone VAdjusts the Vertical Keystone setting.
Keystone HAdjusts the Horizontal Keystone setting.
WhisperSelects the Fan speed. (Normal or Whisper)
MirrorSelects the Mirror status. 
						

							
4

Option
VolumeAdjusts the Volume setting.
TrebleAdjusts the Treble setting.
BassAdjusts the Bass setting.
SRS WOWSelects the SRS WOW setting.
SpeakerTurns Speaker On/Off.
Audio-RGB1Assigns the Audio-RGB1 input terminal.
Audio-RGB2Assigns the Audio-RGB2 input terminal.
Audio-M1-DAssigns the Audio-M1-D input terminal.
Audio-VideoAssigns the Audio-Video input terminal.
Audio-S-VideoAssigns the Audio-S-Video input terminal.
Audio-ComponentAssigns the Audio-Component input terminal.
Auto SearchTurns the Automatic signal search function On/Off.
Auto KeystoneTurns the Automatic keystone distortion correction function On/Off.
Auto onTurns the Auto on function On/Off.
Auto offConfigures the timer to shut off the projector when no signal is detected.
My Button-1Assigns the functions for the MY BUTTON1 buttons on the included remote control.
My Button-2Assigns the functions for the MY BUTTON2 buttons on the included remote control.
Auto AdjustEnables/Disables Auto Adjustment.
Remote Receiv. FrontEnable/Disable Remote Receiv. Front.
Remote Receiv. RearEnable/Disable Remote Receiv. Rear.
Remote Receiv. TopEnable/Disable Remote Receiv. Top.
Remote Freq. NormalEnable/Disable Remote Freq. Normal.
Remote Freq. HighEnable/Disable Remote Freq. High.
Projector Control
Projector Control (Continued)
ItemDescription
Audio
LanguageSelects the Language for the OSD.
Menu Position VAdjusts the vertical Menu Position.
Menu Position HAdjusts the horizontal Menu Position.
BlankSelects the Blank mode.
StartupSelects the Startup screen mode.
MyScreen LockTurns MyScreen Lock On/Off.
MessageTurns the Message function On/Off.
Screen 
						

							
25

Projector Control
Network Restart
Restarts the projector’s network connection.
ItemDescription
RestartRestarts the projector’s network connection in order to activate new configuration settings.
• Restarting requires you to re-log on in order to further control or 
configure the projector via a web browser.
NOTE
Logoff
When logoff is clicked, the logon screen is displayed (6 : Fig. ).
Projector Status
Displays and configures the current projector status.
ItemDescription
Error StatusDisplays the current error status
Lamp TimeDisplays the usage time for the current lamp.
Filter TimeDisplays the usage time for the current filter.
Power StatusDisplays the current power status.
Input StatusDisplays the current input signal source.
Blank On/OffDisplays the Blank On/Off status.
MuteDisplays the current Mute On/Off status.
FreezeDisplays the current Freeze On/Off status. 
						

							
26

Failure & Warning Alerts via E-mail
Failure & Warning Alerts via E-mail
The projector can automatically send an alert to specified e-mail addresses when 
the projector requires maintenance or has encountered an error.
• Up to five e-mail addresses can be specified.
• The projector may be not able to send e-mail if the projector suddenly loses 
power.
NOTE
Mail Settings(10)
To use the projector’s e-mail function please configure the following items via a 
web browser.
Example: If the IP address of the projector is set to 192.168.1.10:
• A Network Restart is required after the SMTP Port configuration 
settings have changed. Click [Network Restart] and configure the following 
items.
NOTE
 6)  Click [Mail Settings] and configure each item. Refer to the [Mail Settings] 
item in [Configuring and Controlling the Projector via a Web Browser] for 
further information.
 7) Click the [Apply] button to save the settings.
• Click the [Send Test Mail] button in [Mail Settings] to confirm 
that the e-mail settings are correct. The following mail will be delivered to the 
specified addresses.
NOTE
Subject line  : Test Mail  
Text : Send Test Mail
  Date  
 Time  
 IP Address  
 MAC Address  
 ) Enter [https://192.168.1.10] into the address bar of the web browser.
 ) Enter the Administrator ID and Password and click [Logon].
 3) Click [Port Settings] on the main menu.
 4) Click the [Enable] check box to open the SMTP Port.
 5) Click the [Apply] button to save the settings. 
						

							
7

Failure & Warning Alerts via E-mail
 8)  Configure the Failure/Warning Alerts via E-mail settings. Click [Alert Settings] 
on the main menu.
 9)  Select and configure each alert item. Refer to [Alert Settings] in [Configuring 
and Controlling the Projector via a Web Browser] for further information.
10) Click the [Apply] button to save the settings.
Failure/Warning e-mails are formatted as follows:
Subject line  :   
Text  : 
  Date  
 Time  
 IP Address  
 MAC Address  
Mail Settings (Continued) 
						

							
8

Projector management via SNMP
Projector management via SNMP
When SNMP is enabled, the projector is able to send Failure/Warning Alerts to a 
specified PC.
• It is recommended that SNMP functions be carried out by a network 
administrator. 
• SNMP management software must be installed on the computer to monitor 
the projector via SNMP.
NOTE
SNMP settings
Configure the following items via a web browser to use SNMP.
Example: If the IP address of the projector is set to 192.168.1.10:
• A Network Restart is required after the SNMP Trap configuration 
settings have been changed. Click [Network Restart] and configure the 
following items.
NOTE
(9)
 5) Click [Security Settings] on the main menu.
 6) Click [SNMP] and set the Community Name on the screen that is displayed.
• A Network Restart is required after the Community Name has been 
changed.
• Click [Network Restart] and configure the following items.
NOTE
 7)  Configure the settings for Trap transmission of Failures/Warnings. Click 
[Alert Settings] on the main menu and select the Failure/Warning item to be 
configured.
 8)  Click the [Enable] check box to send out the SNMP trap for Failures/Warnings. 
Clear the [Enable] check box when SNMP trap transmission is not required.
 9) Click the [Apply] button to save the settings.
 ) Enter [https://192.168.1.10] into the address bar of the web browser.
 ) Enter the Administrator ID and Password and click [Logon].
 3) Click [Port Settings] on the main menu.
 4)  Click the [Enable] check box to open the SNMP Port. 
Set the IP address to send the SNMP Trap to when a  Failure/Warning occurs.