Dukane Imagepro 8918 Projector Users Manual

50

ItemDescription
SECURITY
3.1-3   Input a 4 part PIN Code using the ▲/▼/◄/►/RGB and INPUT buttons.A CONFIRMATION BOX will appear. Reenter the same PIN Code. This will complete the PIN Code registration.NOTE: If there is no key input for about 55 seconds while the PIN BOX or the CONFIRMATION BOX are displayed the menu will close. If necessary repeat 
the process from 3.
 -  .
Afterwards, anytime the projector is restarted after the power switch is turned off the PIN BOX will be displayed....

5

ItemDescription
SECURITY
4. Using the Transition Detector Function
While the Transition Detector function is ON, when power switch is started to supply to the projector, it might react as below.• Transition Detector alarm shown below might appear on screen, if the projector has been moved or re-installed.• Transition Detector alarm might appear on screen, if the MIRROR setting has been changed.• Keystone adjustment feature has been prohibited as long as the Transition Detector function is ON....

5

ItemDescription
SECURITY
4.3 Setting the Transition Detector off
4.3-     Follow the procedure in 4.  -   to display the Transition Detector on/off menu.
4.3-

 
 
Select TURN OFF to display the ENTER PASSWORD BOX (large). 
Enter the registered PASSWORD and the screen will return to the Transition Detector on/off menu.If an incorrect PASSWORD is input the menu will close. If necessary repeat 
the process from 4.3-  .
4.4 If you have forgotten your PASSWORD
4.4-...

53

NETWORK Menu
/07=4)$?5.%6
+2#&&45557$06/#5-
6+/&+((40%
&*%2674010
&(#7.6)#69#;
#0&6+/G5*16+0(14/#6+10548+%
+/#)2+%674
5672+0276
5%40126+10
#7&+1
06914-#5;/07
NETWORK Menu
ItemDescription
DHCP (Dynamic Host Configuration Protocol)
DHCP TURN ON/TURN OFF: Use the ▲/▼ buttons to turn DHCP on/off
TURN ON ó TURN OFF
Select TURN OFF when the network does not have  DHCP enabled.
IP ADDRESS
Entering the IP ADDRESS : 
Use the ▲/▼/◄/► buttons to enter the IP...

54

NETWORK Menu
ItemDescription
TIME DIFFERENCE
Entering the TIME DIFFERENCE : Use the ▲/▼ buttons to enter the TIME DIFFERENCE. Set the same TIME DIFFERENCE as the one set on your PC. If unsure, consult your network administrator. Use the ◄ button to return to the menu after setting the TIME DIFFERENCE.
DATE AND TIME
Entering DATE AND TIME : Use the ▲/▼/◄/► buttons to enter the Year (last two digits), Month, Date, Hour and Minute.
• The projector will override this setting and retrieve  DATE AND TIME...

55

ItemDescription
INFORMATION
INFORMATION display : Use the ► or ENTER buttons to view network information and confirm settings.
• Only the first 16 characters of the projector name are displayed.• The battery for the built in clock may be dead if the clock loses time even when the DATE AND TIME have been set correctly. Replace the battery by following the instructions on replacing the battery. (60)
SERVICE
Choose the RESTART using the ► button.
Then use the ▲ button to execute.
Network will be once...

56

Maintenance
Lamp
A lamp has finite product life. Using the lamp for long periods of time could cause 
the pictures darker or the color tone poor. Note that each lamp has a different 
lifetime, and some may burst or burn out soon after you start using them\
. 
Preparation of a new lamp and early replacement are recommended. To prepare 
a new lamp, contact your dealer and tell the lamp type number.
Type number = 456-8943
Replacing the lamp
. Turn the projector off, and unplug the power cord....

57

Maintenance
Lamp (continued)
 WARNING HIGH VOLTAGE HIGH TEMPERATURE HIGH PRESSURE
►The  projector  uses  a  high-pressure  mercury  glass  lamp.  The  lamp  can break 
with  a  loud  bang,  or  burn  out,  if  jolted  or  scratched,  handled  while  hot,  or  worn over  time.  Note  that  each  lamp  has  a  different  lifetime,  and  some  may  burst  or burn  out  soon  after  you  start  using  them.  In  addition,  when  the  bulb  bursts,  it  is possible  for shards  of  glass  to  fly  into...

58

Please  check  and  clean  the  air  filter  periodically.  If  the  air  filter  becomes  clogged 
by  dust  or  the  like,  internal  temperatures  rise,  which  could  cause  a  fire,  a  burn  or 
malfunction  to  the  projector.  When  the  indicators  or  a  message  prompts  you  to 
clean the air filter, comply with it as soon as possible. Note that the projector may 
shut down, when the projector heats too much.
Please replace the air filter when it is damaged or too soiled. Preparation of...

59

WARNING  ►Before taking care of the air filter, make sure the power 
switch is off and the power cable is not plugged in, then allow the projector to 
cool sufficiently. Taking care of the air filter in a high temperature state of the 
projector could cause an electric shock, a burn or malfunction to the pr\
ojector.
►Use only the air filter of the specified type. Do not use the projector without 
the air filter or the filter cover. It could result in a fire or malfunction to the 
projector.
►Clean...