Dukane Imagepro 8805 Liquid Crystal Projector Users Manual

E-11
Battery Installation
1. Press firmly and slide the battery cover off.
2. Remove both old batteries and install new ones (AA). Ensure that
you have the batteries polarity (+/-) aligned correctly.
3. Slip the cover back over the batteries until it snaps into place. Do not
mix different types of batteries or new and old batteries.
Note on Remote Control Operation:
If you press and hold the SELECT 
 button while installing new
batteries, the remote control may fail to work properly.
Should this...

E-12
3
1
2
INSTALLATION AND CONNECTIONS
This section describes how to set up your projector and how to connect video and audio sources.
To the wall outlet.
Setting Up the Screen and the Projector
Selecting a Location
The further your projector is from the screen or wall, the larger the image. The minimum size the image can be is approximately 25 (0.64 m)
measured diagonally when the projector is roughly 39.4 inches (1.0 m) from the wall or screen. The largest the image can be is 500 (12.7 m) when
the...

E-13
NOTE: Distances may vary +/-5%.
Reflecting the Image
Using a mirror to reflect your projectors image enables you to enjoy a
much larger image. Contact your NEC dealer if you need a mirror. If
youre using a mirror and your image is inverted, use the MENU and
SELECT buttons on your projector cabinet or 
 buttons on your re-
mote control to correct the orientation. (See page E-44.) WARNING
* Installing your projector on the ceiling must be done by a quali-
fied technician. Contact your NEC dealer for...

E-14
Making Connections
NOTE: When using with a notebook PC, be sure to connect between the projector \
and the notebook PC before turning on the power to the  notebook PC. In most
cases signal cannot be output fr om RGB output unless the notebook PC is turned on after connecting with \
the pr ojector.
* If the screen goes blank while using your remote control, it may be th\
e result of the computers screen-saver or power manage ment software.
* If you accidentally hit the POWER button on the remote...

E-15
To connect SCART output (RGB)
Before connections: An exclusive SCART adapter (ADP-SC1) and a
commercially available SCART cable are required for this connection.
NOTE:• Audio signal is not available for this connection.
• The RGB IN 2 connector does not suppor t Plug & Play.
RGB 1 IN
Video equipment
such as D VD player Projector
ADP-SC1Commercially a
vailab le
SCAR T cable F
emale
1. Tu rn  off the po wer to the projector and y our video equipment.
2. Use the NEC ADP-SC1 SCAR T adapter and a...

E-16
AUDIO OUTL
AUDIO INLRRComponentYCbCr
RGB 1 IN
RGB 2 IN
Connecting Your DVD Player
DVD player
You can connect your projector to a DVD player with component output
or Video output. To do so, simply:
1. Turn off the power to your projector and DVD player.
2. If your DVD player has the component video (Y,Cb,Cr) output, use a
commercially available component video cable (RCAX3) and the op-
tional 15-pin-to-RCA (female)

3 cable to connect your DVD player
to the RGB IN1 or IN2 connector on the projector....

E-17
S-VIDEO IN
AUDIO OUTLR
AUDIO INLR
VIDEO OUT
VIDEO IN
S-VIDEO OUT
VCR/ Laser disc player
Connecting Your VCR or Laser Disc Player
Audio equipment S-video cable (not supplied)
Video cable (not supplied)
Audio cable (not supplied)
Use common RCA cables (not provided) to connect your VCR, laser
disc player or document camera to your projector.
To make these connections, simply:
1. Turn off the power to the projector and VCR, laser disc player or
document camera.
2. Connect one end of your RCA cable to...

E-18
PROJECTING AN IMAGE (BASIC OPERATION)
This section describes how to turn on the projector and to project a
picture onto the screen.
Turning on the Projector
NOTE:
• When plugging in or unplugging the supplied power cable, make sure that the
main power switch is pushed to the off[O] position. Failure to do so may cause
damage to the projector.
• The projector has two power switches: main power switch and POWER button
(POWER ON and OFF on the remote control)
• The projector has a feature to prevent...

E-19
Selecting a Source
Selecting the computer or video source
Using the Remote Control
ASPECT
OFF
VIDEO
AUTO ADJ.RGB VIEWER
LASERON
3D REFORMHELPPOINTER
VOLUME MAGNIFY
ZOOM PIC-MUTESLIDE
FOLDER
SLIDE
LIST
POWER
FREEZE
FOCUS
Press an y one of the RGB , VIDEO or
VIEWER b uttons.
Source List
NOTE: If no input signal is available, the projector will display a blue backg\
round(factory preset).
Selecting from Source List
Press and quickly release the SOURCE button on the projector cabinet
to display the...

E-20
Focus
Use the FOCUS Button (+/-) to obtain the best focus.
Correcting the Horizontal and Vertical Key-
stone Distortion (3D Reform)
Use the 3D Reform feature to correct keystone (trapezoidal) distortion
to make the top or bottom and the left or right side of the screen longer
or shorter so that the projected image is rectangular.
In the following description, 3D Reform (Cornerstone) correction can be
done with the USB mouse or remote control, cabinet buttons.
When using the USB connected to the...