Dukane Imagepro 8805 Liquid Crystal Projector Users Manual

							Liquid Crystal Projector
Model 8805
USERS MANUAL 
						

							E-2
Safety Cautions
Precautions
Please read this manual carefully be fore using  your  Dukane
Projector and  keep the ma nual handy  for future re fer ence.
Y our se rial  number is located on the  right side of  your projecto r.
Record it here:
CAUTION
To turn off main power, be sure to remove the plug from power
outlet.
The power outlet socket should be installed as near to the
equipment as possible, and should be easily accessible.
CAUTION
TO PREVENT SHOCK, DO NOT OPEN THE CABINET.
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED NEC SERVICE PER-
SONNEL.
This symbol warns the user that uninsulated voltage within the
unit may be sufficient to cause electrical shock. Therefore, it is
dangerous to make any kind of contact with any part inside of
the unit.
This symbol alerts the user that important information con-
cerning the operation and maintenance of this unit has been
provided.
The information should be read carefully to avoid problems.
WARNINGTO PREVENT FIRE OR SHOCK, DO NOT EXPOSE THIS UNIT TO
RAIN OR MOISTURE.
DO NOT USE THIS UNIT’S GROUNDED PLUG WITH AN EXTEN-
SION CORD OR IN AN OUTLET UNLESS ALL THREE PRONGS
CAN BE FULLY INSERTED.
DO NOT OPEN THE CABINET. THERE ARE HIGH-VOLTAGE COM-
PONENTS INSIDE. ALL SERVICING MUST BE DONE BY QUALI-
FIED NEC SERVICE PERSONNEL.
DOC Compliance Notice
This Class B digital apparatus meets all requirements of the Canadian
Interference-Causing Equipment Regulations.
Acoustic Noise Information Ordinance-3. GSGV:
The sound pressure level is less than 70 dB (A) according
to ISO 3744 or ISO 7779.
This label is on the side of the remote control.
RF Interference
WARNING
The Federal Communications Commission does not allow any
modifications or changes to the unit EXCEPT those specified
by  Dukane  corporation  in this ma nual.  F ailure to com ply
with this g overnment regulation could  void  your right to
operate this equipment. This equipment has been tested and
found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guar-
antee that interference will not occur in a particular installa-
tion. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio / TV technician for help.
In UK, a BS approved power cable with moulded plug has a Black (five
Amps) fuse installed for use with this equipment. If a power cable is not
supplied with this equipment please contact your supplier.
Important Safeguards
These safety instructions are to ensure the long life of your projector
and to prevent fire and shock. Please read them carefully and heed all
warnings.
Installation
1. For best results, use your projector in a darkened room.
2. Place the projector on a flat, level surface in a dry area away from dust and moisture.
To avoid premature lamp failure, do not tilt the front of the projector
up or down by more than 15° from level.
3. Do not place your projector in direct sunlight, near heaters or heat radiating appliances.
4. Exposure to direct sunlight, smoke or steam can harm internal com- ponents.
5. Handle your projector carefully. Dropping or jarring can damage in- ternal components.
6. Do not place heavy objects on top of the projector.
7. If you wish to have the projector installed on the ceiling:
a. Do not attempt to install the projector y ourself.
b . The projector must be installed b y qualified technicians in order
to ensure proper operation and reduce the r isk of bodily injury.
c. In addition, the ceiling m ust be strong enough to suppor t the
projector and the installation m ust be in accordance with any
local b uilding codes .
d. Please consult y our dealer for more information.
CAUTION
Do not look into the laser pointer while it is on and do not
point the laser beam at a person. Serious injury could re-
sult.
Important Information 
						

							E-3
Fire and Shock Precautions
1. Ensure that there is sufficient ventilation and that vents are unob-structed to prevent the build-up of heat inside your projector. Allow
at least 3 inches (10 cm) of space between your projector and a
wall.
2. Prevent foreign objects such as paper clips and bits of paper from falling into your projector.
Do not attempt to retrieve any objects that might fall into your projec-
tor. Do not insert any metal objects such as a wire or screwdriver
into your projector. If something should fall into your projector, dis-
connect it immediately and have the object removed by a qualified
NEC service personnel.
3. Do not place any liquids on top of your projector.
4. Do not look into the lens while the projector is on. Serious damage to your eyes could result.
5. Keep any items such as magnifying glass out of the light path of the projector. The light being projected from the lens is extensive, there-
fore any kind of abnormal objects that can redirect light coming out
of the lens, can cause unpredictable outcome such as fire or injury
to the eyes.
6. Do not cover the lens with the supplied lens cap or equivalent while the projector is on. Doing so can lead to melting of the cap and
possibly burning your hands due to the heat emitted from the light
output.
7. The projector is designed to operate on a power supply of 100-120 or 200-240 V 50/60 Hz AC. Ensure that your power supply fits this
requirement before attempting to use your projector.
8. Handle the power cable carefully and avoid excessive bending. A damaged cord can cause electric shock or fire.
9. If the projector is not to be used for an extended period of time, disconnect the plug from the power outlet.
CAUTION
1. Do not try to touch the ventilation outlet on the front as it can be-come heated while the projector is turned on.
2. Do no use the tilt-foot for purposes other than originally intended. Misuses such as gripping the tilt-foot or hanging on the wall can
cause damage to the projector.
3. Enable High-Speed Fan mode if you continue to use the projector for consecutive days. (From the Advanced menu, select [Projector
Options]  → [Setup]  → [Page 4]  → [High Speed Fan Mode].)
4. Do not unplug the power cable from the wall outlet under any one of the following circumstances.
Doing so can cause damage to the projector:
* While the Hour Glass icon appears .
* While the message Please w ait a moment. appears. This mes-
sage will be displa yed after the projector is tur ned off.
* While the cooling f ans are running. (The cooling f ans continue to
work f or 90 seconds after the projector is tur ned off).
5. Do not eject the PC card or LAN card while its data is being accessed.
Doing so can damage your PC card or LAN card data.
Lamp Replacement
• To replace the lamp, follow all instructions provided on page E-53.
• Be sure to replace the lamp when the message  The lamp has
reached the end of its usable life. Please replace the lamp.
appears. If you continue to use the lamp after the lamp has reached
the end of its usable life, the lamp bulb may shatter, and pieces of
glass may be scattered in the lamp case. Do not touch them as the
pieces of glass may cause injury.
If this happen s, contact  your  Dukane  dealer for lamp replacement.
• Allow a minimum of 90 seconds to elapse after turning off the pro- jector. Then turn off the main power switch, disconnect the power
cable and allow 60 minutes to cool the projector before replacing
the lamp.
Whats in the Box?Make sure your box contains everything listed. If any pieces are miss-
ing, contact your dealer.
Lens cap
Remote control Pow er cab le
Projector
Remote Control Cab
le
CD-R OM
Projector User Suppor tware
USB cab le
Users
Manual
Batter iesString and r iv e t
RGB signal cab le
USB mouseOFF
VIDEOAUT O ADJ.RGB VIEWER
LASER
POWER
ON
P
JASPEC T3
D 
REFO RMHELPPO
INT ERVOL UMEMA
GN IFYZOO MP
IC-M
UTESLIDEFO
LDE
R
S LIDELIS T
S
E
LE
C
T
FRE EZEFOC
US 
						

							E-4
TABLE OF CONTENTS
Important Information ..................................................... E-2Safety Cautions ........................................................................\
....................................... E-2
Whats in the Box? ........................................................................\
.................................. E-3
INTRODUCTION .............................................................. E-5Introduction to the Projector ........................................................................\
................... E-5
Part Names of the Projector ........................................................................\
.................... E-6 Attaching the lens cap ........................................................................\
......................... E-6
Carrying the Projector ........................................................................\
......................... E-6
Top Features ........................................................................\
........................................ E-7
Terminal Panel Features ........................................................................\
....................... E-8
Part Names of the Remote Control ........................................................................\
...... E-9Battery Installation ........................................................................\
......................... E-11
Remote Control Precautions ........................................................................\
.......... E-11
Operating Range for Wireless Remote Control ...................................................... E-11
Using the Remote Control in Wired Operation ....................................................... E-11
INSTALLATION AND CONNECTIONS ....................................... E-12Setting Up the Screen and the Projector ....................................................................... E-12Selecting a Location ........................................................................\
.......................... E-12
Throw Distance and Screen Size ........................................................................\
....... E-13
Making Connections ........................................................................\
.............................. E-14 When Viewing a DVI Digital Signal ........................................................................\
.... E-14
Connecting Your PC or Macintosh Computer ............................................................ E-14
To connect SCART output (RGB) ........................................................................\
....... E-15
Connecting an External Monitor ........................................................................\
........ E-15
Connecting Your DVD Player ........................................................................\
............. E-16
Connecting Your VCR or Laser Disc Player ............................................................... E-17
Connecting the Supplied Power Cable ....................................................................... E-17
PROJECTING AN IMAGE (BASIC OPERATION) ........................... E-18Turning on the Projector ........................................................................\
........................ E-18
Selecting a Source ........................................................................\
................................. E-19
Adjusting the Picture Size and Position ........................................................................\
. E-19
Correcting the Horizontal and Vertical Keystone Distortion (3D Reform) ...................... E-20
Optimizing RGB Picture Automatically ........................................................................\
.. E-22
Turning Up or Down Volume ........................................................................\
................. E-22
Using the Laser Pointer ........................................................................\
......................... E-22
Setting the function switch ........................................................................\
.................... E-23
Turning off the Projector ........................................................................\
....................... E-23
CONVENIENT FEATURES ................................................... E-24Using the Remote Mouse Function ........................................................................\
....... E-24Connecting to your computer for the remote mouse function ................................... E-24
When using the USB Port ........................................................................\
.................. E-24
Switching operation mode between computer and projector ..................................... E-24
Turning Off the Image and Sound ........................................................................\
.......... E-25
Freezing a Picture ........................................................................\
.................................. E-2 5
Using the Pointer ........................................................................\
.................................. E-25
Enlarging and Moving a Picture ........................................................................\
............. E-25
Getting the On-line Help ........................................................................\
........................ E-25
Using the USB Mouse ........................................................................\
........................... E-26
Using the USB HUB Function ........................................................................\
................ E-26
Changing Background Logo ........................................................................\
.................. E-27
Making Freehand Drawings on a Projected Image (ChalkBoard) ................................... E-27
USING THE VIEWER ........................................................ E-28Making the Most out of the Viewer Function ................................................................. E-28
Operating the Viewer Function from the Projector (playback) ....................................... E-29 Projecting slides (Viewer) ........................................................................\
.................. E-29
Auto Play Mode ........................................................................\
................................. E-30
Switching to Slides Directly from Other Input Modes ................................................ E-30
Viewing Digital Images ........................................................................\
...................... E-30
Storing Images Displayed on the Projector on the PC card (Capture) ....................... E-30
Deleting Captured Images ........................................................................\
................. E-31
Using the PC Card Files Fucntion (PC Card Files) ...................................................... E-31
USING ON-SCREEN MENU ................................................. E-32Basic Menu Operation ........................................................................\
........................... E-32Using the Menus ........................................................................\
............................... E-32
Customizing the Menu ........................................................................\
....................... E-32
Menu tree ........................................................................\
.............................................. E-33
Menu Elements ........................................................................\
..................................... E-36 Entering Alphanumeric Characters by Using the Menu .............................................. E-37
Menu Descriptions & Functions ........................................................................\
............ E-37 Source Select ........................................................................\
.................................... E-37RGB/Video/S-Video/DVI (DIGITAL)/Viewer/LAN/Entry List
Picture ........................................................................\
............................................... E -38
Sound ........................................................................\
................................................ E- 38
Image Options ........................................................................\
................................... E-38 Selecting Aspect Ratio ........................................................................\
................... E-38
Masking Unwanted Area (Blanking) ....................................................................... E-39
Adjusting Position and Clock ........................................................................\
......... E-39
Horizontal/Vertical Position ........................................................................\
............ E-39
Selecting Resolution ........................................................................\
...................... E-39
Selecting Overscan Percentage ........................................................................\
...... E-39 Selecting Video Filter Level ........................................................................\
............ E-39
Selecting Noise Reduction Level ........................................................................\
.... E-39
Signal Type ........................................................................\
.................................... E-39
Picture Management ........................................................................\
.......................... E-39 User Adjust (when using User 1 to 4) .................................................................... E-39 Selecting Gamma Correction Mode ................................................................ E-40
Selecting Color Correction ........................................................................\
..... E-40
Adjusting Color Temperature and White Balance ............................................ E-40
Selecting Base Setting ........................................................................\
............ E-40
Projector Options ........................................................................\
.............................. E-40 Using 3D Reform ........................................................................\
........................... E-40 Cornerstone ........................................................................\
........................... E-40
Keystone ........................................................................\
................................ E-40
Using Adapting Color Correction ........................................................................\
... E-41
Menu [Page1] ........................................................................\
................................ E-43 Selecting Menu Language/Selecting Menu Mode/Customizing the Menu/Select-\
ing Projecting Pointer Icon/Selecting Menu Display Time
Menu [Page 2] ........................................................................\
............................... E-43 Turning On / Off Source Display / Turning On / Off Message / Selecting Menu
Color
Setup [Page 1] ........................................................................\
............................... E-44 Selecting Projector Orientation/Selecting a Color or Logo for Background\
/Setting
RGB 1 or 2 for RGB OUT/Setting Closed Caption
Setup [Page 2] ........................................................................\
............................... E-44 Setting Viewer Options/Selecting Capture Options/Setting Mouse Button an\
d Sen-
sitivity/Selecting Operation Mode
Setup [Page 3] ........................................................................\
............................... E-45 Selecting Signal Format [Signal Select]
Setup [Page 4] ........................................................................\
............................... E-45 Enabling Auto Adjust/Enabling Auto Start/Enabling Power Management/Enabl\
ing
Power Off Confirmation/Enabling Horizontal and Vertical Keystone Correction Save
/Enabling High Speed Fan Mode/Selecting Built-in Speakers/Enabling Idle \
Mode
Setup [Page 5] ........................................................................\
............................... E-46 Remote Sensor/S-Video Mode Select
Setup [Page 6] ........................................................................\
............................... E-46 Selecting Communication Speed/Selecting Default Source/Disabling the Cabinet
Buttons
Selecting Lamp Mode and Lamp Type ................................................................... E-46
Selecting Aspect Ratio and Position for Screen ..................................................... E-47
Selecting Auto Functions ........................................................................\
............... E-47
Setting LAN Mode ........................................................................\
............................. E-48 IP Address ........................................................................\
..................................... E-48
Network Type ........................................................................\
................................. E-48
WEP ........................................................................\
............................................... E-49
Mail ........................................................................\
................................................ E-49
Status ........................................................................\
............................................ E-50
Setting a Password ........................................................................\
............................ E-50
Security ........................................................................\
............................................. E- 51
Tools ........................................................................\
.................................................. E-52
Using Sleep Timer/Using Capture/Using PC Card Files/Using ChalkBoard
Help ........................................................................\
................................................... E-52
Contents ........................................................................\
........................................ E-52
Information ........................................................................\
.................................... E-52
Returning to Factory Default ........................................................................\
.............. E-52
MAINTENANCE ............................................................. E-53Replacing the Lamp ........................................................................\
.............................. E-53
Cleaning ........................................................................\
............................................... . E-54
Cleaning or Replacing the Filter ........................................................................\
......... E-54
Cleaning the Cabinet and the Lens ........................................................................\
..... E-54
TROUBLESHOOTING ........................................................ E-55Power Indicator ........................................................................\
..................................... E-5 5
Status Indicator ........................................................................\
..................................... E- 55
Lamp Indicator ........................................................................\
...................................... E-5 5
Common Problems & Solutions ........................................................................\
............ E-56
When using the Viewer function ........................................................................\
............ E-56
SPECIFICATIONS ........................................................... E-57
APPENDIX ................................................................... E-58
Cabinet Dimensions ........................................................................\
.............................. E-58
Pin Assignments of D-Sub RGB Input Connector .......................................................... E-58
Compatible Input Signal List ........................................................................\
................. E-59
PC Control Codes and Cable Connection ....................................................................... E-60
PC Control Connector (D-SUB 9P) ........................................................................\
........ E-60
Using Software Keyboard ........................................................................\
...................... E-60
Operation Using an HTTP Browser ........................................................................\
........ E-61 
						

							E-5
INTRODUCTION
Introduction to the ProjectorThis section introduces you to  your n ew Pro jector and describes
the  features and control s.
Congratulations on  Your Pu rchase of Th is Projector
The Dukane ImagePro 8805  is one of the ve ry best projectors  avail-
a ble tod ay. The  ImagePro 8805  enables  you to project precise
images up to 500 inches across (measured diagonally) from your PC or
Macintosh computer (desktop or notebook), VCR, DVD player, docu-
ment camera, a laser disc player or Viewer.
You can use the projector on a tabletop or cart, you can use the projec-
tor to project images from behind the screen, and the projector can be
permanently mounted on a ceiling*
1. The remote control can be used
wirelessly.
*
1Do not attempt to mount the projector on a ceiling yourself.
The projector must be installed by qualified technicians in order
to ensure proper operation and reduce the risk of bodily injury.
In addition, the ceiling must be strong enough to support the pro-
jector and the installation must be in accordance with any local
building codes. Please consult your dealer for more information.
Features youll enjoy:
• 3D Reform enhanced keystone correction that allows not only hori-zontal and vertical access but diagonal adjustments.
• Wireless*
2 or wired networking access provides easy and effective
presentation delivery.
*
2  A wireless LAN card is required.  The optional wireless LAN
card is available. (SWL-2100N-N
∗)
• Safety protect by Password and Security functions Password and Security features prevent the projector from being used
by unauthorized individuals.
Password prevents unauthorized individuals from changing projector
settings or adjustments Security offers complete protection by using
your PC card as a protect key so that the projector will not project a
signal without insertion of the registered PC card and unauthorized
use can be discouraged.
• Picture Management enables users to adjust individual color settings to their preferences.
• Eco-mode extends lamp life and reduces total cost of ownership. Standard lamp and optional longer life lamp
• Power zoom and power focus standard lens provide easy adjust- ment.
• Automatic lens focus provides extreme ease of use
• Automatic Wall Color Correction allows for quick adaptive color cor- rection on textured or painted walls and in applications where the
display is other than screen material. With the built-in image sensor,
the projector adjusts the colors for screen sizes between 40 and
150 diagonally.
• Variable audio out control via projector
• The built-in Viewer allows you to start your presentation even when a PC is not available at the site.
• A high-bright 275 watt DC lamp (220W Eco mode).
• The Standby mode reduces standby power consumption significantly.
• The supplied wireless remote control that operates the projector from any angle.
• The image can be projected between 25 and 500 inches (measured diagonally).
• The Capture enables you to capture the current projected image.
• An image can be projected from in front or behind a screen, and the projector can even be installed on the ceiling. •
  Exclusi ve intelligent pi xel  blending tech nology - an extremely
accu rate image compression technology - of fers a crisp
image with UXGA (160 0
 1200) resolution*
3.
•   Suppo rts most IBM  V GA, S VGA, XGA, SXGA/UXGA( compressed)
Macintosh, component signal (YCbCr/  YPbPr) or a ny other
RGB signals within a ho riz ontal frequency range of 24 to 100
kHz and a vertical frequency range of 48 to 120 Hz. This includes
NTSC, PAL, PAL-N, PAL-M, PAL60, SECAM and NTSC4.43 stan-
dard video signals.
NOTE:  Composite video standards are as follows:
NTSC: U.S. TV standard for video in U.S. and Canada. P AL: TV standar d used in Western Eur ope.
P AL-N: TV standar d used in Argentine, Paraguay and Uruguay .
P AL-M: TV standar d used in Brazil.
P AL60: TV standar d used for NTSC playback on P AL TVs.
SECAM: TV standard used in France and Eastern Europe.
NTSC4.43: TV standard used in Middle East countries.
• The supplied remote control can be used without a cable, and you can even use the remote control to operate your PCs mouse wirelessly
from across the room with the built-in remote mouse function.
• You can control the projector with a PC using the PC Control port.
• USB port allows USB mouse operation*
4.
*4The USB ports meet the USB1.1 specification.
• The contemporary cabinet design is light, compact, easy to carry, and complements any office, boardroom or auditorium.
• Eight pointers are available for your presentation.
About this users manual
The fastest way to get started is to take your time and do ev-
erything right the first time. Take a few minutes now to review
the users manual. This may save you time later on. At the be-
ginning of each section of the manual youll find an overview. If
the section doesnt apply, you can skip it. 
						

							E-6
AC INRG B2 INR G B  O
UT
A
U
DIO
A UDIOD
VI I NU SB(M OUSE/H UB)REM
OTEA U
DIO
A UDIO G
/Y
B/C
b H
V
R
G B1 IN
S -V
ID
EO  INV
ID
EO  IN
A
UD IO
A U
DIO
A UDIOL/MONORL/MONOR A
UDIO  O
UT
L
/M
ONO R P
C  C ONTR
O L
1
2
Part Names of the Projector
Ventilation (outlet)
Heated air is e xhausted from here
* This security slot supports the MicroSaver® Security System. MicroSaver® is a registered trademark of Kensington Microware Inc. The logo is
trademarked and owned by Kensington Microware Inc.
Built-in Security Slot  (  )*
Adjustab le Tilt F oot Le ve r
(See page E-19)
Attaching the lens cap
To attach the lens cap to the bottom with the supplied string and rivet:
Remote Sensor (See page E-11)
Controls (See page E-7)
Filter Co ver (inlet)
Carr
ying Handle
Lens CapLens
Adjustab le Tilt F oot (See page E-19)
Stereo Speak er (5W) A
C  Input
Connect the supplied po wer cab les three-
pin plug here , and plug the other end into
an activ e wall outlet.  (See page E-17)
Main P ow er Switch
When y ou plug the supplied po wer cab le into
an activ e wall outlet and tur n on the Main
P ow er s witch, the PO WER indicator tur ns
or ange and the projector is in standb y mode.
(See page E-18)
Remote Sensor
(See page E-11) PC Card Slot 1
PC Card Slot 2
Lamp Co
ver (See page E-53)
PC Card Eject Button
1. Thread the str ing through the
hole on the lens cap and then tie a knot in the str ing.
2 . Use the r iv et to attach the
str ing to the bottom of the
projector . Image Sensor
F or A uto F ocus and A uto Wall Color
Correction. (See page E-47)
Carrying the Projector
Always carry your projector by the handle.
Ensure that the power cable and any other cables connecting to video
sources are disconnected before moving the projector.
When moving the projector or when it is not in use, cover the lens with
the lens cap.
V entilation (inlet)
Remote Sensor (See page E-11)
Adjustable Tilt F oot Le ve r
(See page E-19)
Adjustab le Tilt Foot
(See page E-19)
Remote Sensor (See page E-11) 
						

							E-7
11 10 9 84
1412 13 256
17
3
Top Features
1. POWER Button (ON / STAND BY)(  )
Use this button to turn the power on and off when the main power is
supplied and the projector is in standby mode.
NOTE:  To  tur n on or of f the projector , press and hold this button for a mini-mum of two seconds.
2. POWER Indicator
When this indicator is green, the projector is on; when this indicator
is orange, it is in standby or idle mode. See the Power Indicator sec-
tion on page E-55 for more details.
3. STATUS Indicator If this light blinks red rapidly, it indicates that an error has occurred,
the lamp cover is not attached properly or the projector has over-
heated. If this light remains orange, it indicates that you have pressed
a cabinet key while the Control Panel Key Lock is enabled. See the
Status Indicator section on page E-55 for more details.
4. LAMP Indicator If this light blinks red rapidly, its warning you that the lamp has reached
the end of its usable life. After this light appears, replace the lamp as
soon as possible (See page E-53). If this is lit green continually, it
indicates that the lamp mode is set to Eco. See the Lamp Indicator
section on page E-55 for more details.
5. SOURCE Button Use this button to select a video source such as a PC, VCR, DVD
player, Viewer (PC card), or LAN.
Press and release this button quickly to display the Source List.
Each time this button is pressed for a minimum of ONE second, the
input source will change as follows:
RGB1  → RGB2  → Video  → S-Video  → DVI (DIGITAL)*  → Viewer  → RGB1  → ...
If no input signal is present, the input will be skipped.
6. AUTO ADJUST Button Use this button to adjust Position-H/V and Pixel Clock/Phase for an
optimal picture (See page E-22). Also press and hold this button for a
minimum of 2 seconds to enable the Auto Focus* or Auto Wall Color
Correction* function (See page E-47).
7. 3D REFORM Button Press this button to enter 3D Reform mode to correct the keystone
(trapezoidal) distortion, and make the image square.
8. ZOOM Button (+/-) Zoom the lens in and out.
9. FOCUS Button (+/-) Adjust the lens focus.
10. MENU Button Displays the menu. 11. SELECT 

 (+) (–) / Volume Buttons

  : Use these buttons to select the menu of the item you wish to
adjust. When no menus appear, these buttons work as a vol-
ume control.
   : Use these buttons to change the level of a selected menu item.
A press of the   button executes the selection. When the menus
or the Viewer tool bar is not displayed, these buttons can be
used to select a slide, or to move the cursor in Folder List or
Slide List.
When the pointer is displayed, these  
 buttons move the pointer.
12. ENTER Button Executes your menu selection and activates items selected from the
menu.
13. CANCEL Button Press this button to exit Menus. Press this button to return the ad-
justments to the last condition while you are in the adjustment or
setting menu.
14. PC CARD Access Indicator 1/2 Lights while accessing a PC card. 
						

							E-8
1. RGB1 IN / Component Input Connector (Mini D-Sub 15 Pin)Connect your computer or other analog RGB equipment such as IBM
compatible or Macintosh computers. Use the supplied RGB cable to
connect to your computer. This also serves as a component input
connector that allows you to connect a component video output of
component equipment such as a DVD player. This connector also
supports SCART output signal. See page E-15 for more details.
RGB1 AUDIO Input Mini Jack (Stereo Mini)
This is where you connect the audio output from your computer or
DVD player when connected to the RGB1 input. A commercially avail-
able audio cable is required.
2. RGB2 IN / Component Input Connectors (BNC) Connect R,G,B,H (Horizontal sync) and V (Vertical sync) outputs of
external equipment.
If using a component with a combined sync (SYNC) output, connect
it to the H/V terminal.
When using luminance and color-difference signals of HDTV and DVD,
connect Pr/Cr to the R,Y to the G and Pb/Cb to the B input of the
projector.
NOTE:  The RGB IN 2 does not support Plug & Play .
RGB2 AUDIO IN Mini Jack (Stereo Mini)
This is where you connect audio output from your computer or DVD
player connected to the RGB2 input. A commercially available audio
cable is required.
3. DVI IN Connector (24 pin)
This connector can be used to accept a digital signal output from a
computer or other sources with a DVI connector.
DVI AUDIO Input Mini Jack (Stereo Mini)
This is where you connect the audio output from your computer when
connected to the DVI input. A commercially available audio cable is
required. On MT860 this AUDIO input mini jack is used for Viewer
and LAN exclusively.
4. RGB OUT Connector (Mini D-Sub 15 Pin) You can use this connector to loop your computer image to an exter-
nal monitor from the RGB 1 or 2 input source.
The RGB analog signal set on RGBOUT Terminal is output during
idle mode. See pages E-15 and 45.
RGB AUDIO OUT Mini Jack (Stereo Mini)
Connect an additional audio equipment here to listen to audio com-
ing from your computer connected to RGB1, RGB2 or DVI input (not
available on MT860).
Note that there is no audio output from this jack during Standby and
Idle.
Terminal Panel Features
8 9 10 13 12
3
2
1
5 6 4711
5. S-VIDEO IN Connector (Mini DIN 4 Pin)
Here is where you connect the S-Video input from an external source
like a VCR.
NOTE:  S-Video provides more vivid color and higher resolution than the tra-ditional composite video format.
S-VIDEO AUDIO Input Jacks R/L (RCA)
These are your left and right channel audio inputs for stereo sound
from an S-Video source.
6. VIDEO IN Connector (RCA) Connect a VCR, DVD player, laser disc player, or document camera
here to project video.
VIDEO AUDIO Input Jacks R/L (RCA)
These are your left and right channel audio inputs for stereo sound
from a Video source.
7. AUDIO OUT Jacks R/L (RCA) You can use this connector to output sound from the currently se-
lected input source (RGB 1, RGB 2, DVI (DIGITAL) (not available on
MT860), Video or S-Video).
Output sound level can be adjusted in accordance with the sound
level of the internal speaker.
8. USB Port (MOUSE/HUB) [Type A] Connect the supplied USB mouse. You can operate the menu or Viewer
with the USB mouse via this port.
• A USB-suppor ted scanner or PC per ipheral can be connected
to this por t. (USB Hub Function)
9. USB Port (PC) [Type B]
Connect this port to the USB port (type A) of your PC using the sup-
plied USB cable. You can operate your computers mouse functions
from the remote control. This port also serves as a PC Control port
by using Dynamic Image Utility 2.0 included on the supplied CD-
ROM.
10. REMOTE (Mini Jack) Connect your remote control cable here for wired operation.
11. PC CONTROL Port (D-Sub 9 Pin) Use this port to connect your PC to control your projector via a serial
cable. This enables you to use your PC and serial communication
protocol to control the projector. A commercially available RS232C
cross cable is required to use this port. You can also control the pro-
jector by using Dynamic Image Utility 2.0 included on the supplied
CD-ROM.
To do so you must first have Dynamic Image Utility 2.0 installed on
your PC. If you are writing your own program, typical PC control codes
are on page E-60.
12. PC CARD Slot 1/2 Insert a PC card, commercially available LAN card or NEC optional
wireless LAN card here.
There are two slots: Slot 1 and Slot 2.
NOTE:  A dummy card is inserted into each slot at the time of shipment. Firstremove the dummy cards before use.
13. PC CARD Eject Button 1/2
Press to eject a PC card partially. Each slot has its own eject button:
1 and 2. 
						

							E-9
Part Names of the Remote Control
NOTE: If you ar e using a Macintosh computer , you can click either the right-clickor left-click button to activate the mouse.
PJFRE EZ E3
D  REFORMPIC -M U
TEE
OFF
VIDEO
AU TO ADJ.RGB
VIEWER
LASER ONPOW
ER
SELECT
21
3
1. Infrared Transmitter
Direct the remote control toward
the remote sensor on the projec-
tor cabinet.
2. LASER Pointer Beams a laser light when the LA-
SER button is pressed.
3. Remote Jack Connect your remote control
cable here for wired operation.
MENU
PJ
ASPECT
OFF
VIDEO
AUTO ADJ.
RGB VIEWER
LASERON
3D REFORM
HELPPOINTER
VOLUME MAGNIFY
ZOOM PIC-MUTE
SLIDE
FOLDER
SLIDE
LIST
ENTERCANCEL
POWER
SELECT
FREEZE
FOCUS
16
21
19
22
27
28
29
17
20
23
25
26 24 1514
12
1110 97 8 5
6 4
18
13
9. VIEWER ButtonPress this button to select the Viewer source.
10. AUTO ADJ Button Use this button to adjust an RGB source for an optimal picture. Also
press and hold this button for a minimum of 2 seconds to enable the
Auto Focus* or Auto Wall Color Correction* function. See page E-20
or 22.
11. LASER Button Press and hold this button to activate the laser pointer. When lit, you
can use the laser to draw your audiences attention to a red dot that
you can place on any object.
12. MENU Button Displays the menu for various settings and adjustments.
13. SELECT  
 (Mouse) Button
When you are in the Computer mode, these buttons work as a com-
puter mouse.
When you are in the Projector mode, which is indicated by lighting
the PJ button. See page E-24.

  : Use these buttons to select the menu of the item you wish
to adjust.
  : Use these buttons to change the level of a selected menu
item. A press of the   button executes the selection.
When the pointer is displayed, these  
 buttons move the pointer.
When the pointer is not displayed, these  
 buttons are for adjust-
ing the image.
14. ENTER (Left Click) Button When you are in the Computer mode, this button works as the mouse
left button. When this button is pressed and held for a minimum of 2
seconds, the drag mode is set. When you are in the Projector mode,
which is indicated by lighting the PJ button: Use this button to enter
your menu selection. It works the same way as the ENTER button on
the cabinet. See page E-7.
15. CANCEL (Right Click) Button When you are in the Computer mode, this button works as the mouse
right button. When you are in the Projector mode, which is indicated
by lighting the PJ button: Press this button to exit the Menus. It works
the same way as the CANCEL button on the cabinet. See page E-7.
16. PJ Button Press this button to switch the SELECT, CANCEL, and ENTER but-
tons between the Projector mode (lit red) and the Computer mode.
Press this button or any one of the POWER ON/OFF, MENU, AS-
PECT, 3D REFORM, HELP, POINTER, MAGNIFY, VIEWER, FOLDER
LIST or SLIDE LIST buttons to switch to the Projector mode and the
PJ button lights red. To switch back to the Computer mode, press the
PJ button again. See page E-24.
17. ASPECT Button Press this button to display the Aspect Ratio select screen. See page
E-38.
18. FREEZE Button This button will freeze a picture. Press again to resume motion.
19. 3D REFORM Button Press this button to enter 3D Reform to correct the keystone (trap-
ezoidal) distortion, and make the image square. See page E-20.
20. HELP Button Provides the online help or the set information.
21. POINTER Button Press this button to display one of the eight pointers; press again to
hide the pointer. You can move your pointer icon to the area you want
on the screen using the Select  
 button. See page E-25.
4. LED
Flashes when any button is pressed.
5. POWER ON Button When the main power is on, you can use this button to turn your
projector on.
NOTE:  To  turn on the pr ojector, press and hold the POWER ON button for aminimum of two seconds.
6. POWER OFF Button
You can use this button to turn your projector off.
NOTE:  To  tur n off the projector , press and hold the POWER OFF button for aminimum of two seconds.
7. VIDEO  Button
Press this button to toggle between Video and S-Video inputs.
8. RGB Button Press this button to select RGB 1, RGB 2 or DVI (DIGITAL)* inputs.
Each time this button is pressed, the input source will change as
follows:
RGB 1  → RGB 2  → DVI (DIGITAL)*  → RGB 1  → ... 
						

							E-10
MENU
PJ
ASPECT OFF
VIDEO
AUTO ADJ.
RGB VIEWER
LASERON
3D REFORM
HELPPOINTER
VOLUME MAGNIFY
ZOOMPIC-MUTE
SLIDE
FOLDER
SLIDE
LIST
ENTERCANCEL
POWER
SELECT
FREEZE
FOCUS
16
21
19
22
27
28
29 17
20
23
25
26 2415 14 1211 109 78 5 64
18
13
22. PICTURE MUTE Button
This button turns off the image and sound for a short period of time.
Press again to restore the image and sound.
NOTE: When the menu is displayed, a press of this button mutes an imageand sound without turning off the menu.
23. VOLUME (+)(–) Button
Press (+) to increase the volume and (–) to decrease it.
24. MAGNIFY (+)(–) Button
Use this button to adjust the image size up to 400%. When the pointer
is displayed, the image is magnified about the center of the pointer.
When the image is magnified, the pointer is changed to the magnify-
ing icon.
When the pointer is not displayed, the image is magnified about the
center of the screen. See page E-25.
25. ZOOM (+)(–) Button
Zoom the lens in and out.
26. FOCUS (+)(–) Button
Adjust the lens focus.
27. SLIDE (+)(–) Button
Press (+) to select the next folder or slide and (–) to select the previ-
ous folder or slide. See page E-29.
28. FOLDER LIST Button
Press this button to select Viewer source to display a list of folders
included in a PC card. See page E-29.
29. SLIDE LIST Button
Press this button to select Viewer source to display a list of slides
included in a PC card. See page E-29.
NOTE: The default is the Computer mode, which allows you to use the SELECT,
CANCEL, and ENTER buttons as your computer mouse. When the POWER ON/
OFF, MENU, ASPECT, 3D REFORM, HELP, POINTER, MAGNIFY, VIEWER, FOLDER
LIST, or SLIDE LIST button is pressed, the PJ button lights red to indicate that
you are in the Projector mode. If no buttons are pressed within 60 seconds, the
light goes out and the Projector mode is canceled.