Dukane Imagepro 8755n Projector Users Manual

61
OPTION menu
ItemDescription
SERVICE
(continued) REMOTE FREQ.
(1) 
 Use the ▲/▼ button to change the projector's remote sensor 
frequency setting  (
19).
1:NORMAL  ó 2:HIGH
(2)   Use the ◄/► button to change the 
projector's remote sensor on or off.
ON  ó OFF
The factory default setting is for both 1:NORMAL and 2:HIGH to be on. 
If the remote control does not function correctly, disable either of them.
It's not possible to disable both options at the same time.
COMMUNICATION
Selecting this...

62
OPTION menu
ItemDescription
SERVICE
(continued)
COMMUNICATION(continued)
COMMUNICATION TYPE
Select the communication type for transmission via 
the CONTROL port.
NETWORK BRIDGE: Select this type, if it is  required to control an external device as a 
network terminal, via this projector from the 
computer.
The CONTROL port doesn't accept RS-232C  
commands (Network Bridge Function in the 
Network Guide)
OFF: Select this mode to receive RS-232C  commands using the  CONTROL port. 
• OFF is selected...

63
OPTION menu
ItemDescription
SERVICE
(continued)
COMMUNICATION (continued)
RESPONSE LIMIT TIME
Select the time period to wait for receiving 
response data from other device communicating by 
the NETWORK BRIDGE and the HALF-DUPLEX 
through the CONTROL port.
OFF  ó 1s 
ó 2s 
ó 3s
    
OFF: Select this mode if it is not required to check  the responses from the device that the projector 
sends data to. In this mode, the projector can 
send out data from the computer continuously.
1s /2s /3s: Select the...

64
OPTION menu
ItemDescription
SERVICE
(continued)
CLONING(continued)
The following items are exempted.
OPTION: LAMP TIME, FILTER TIME, 
SERVICE(GHOST)
NETWORK: WIRELESS AND WIRED SETUP (IP ADDRESS, SUBNET MASK, 
DEFAULT GATEWAY, DATE AND 
TIME), MY IMAGE, PRESENTATION
SECURITY: MY TEXT DISPLAY
• Operation is not available if SECURITY_
CLONNING LOCK is turned ON.
• The Screen_MyScreen can only be loaded.
CLONING load function on STANDBY MODE
• While the projector is in STANDBY MODE, push 
the INPUT...

65
OPTION menu
ItemDescription
SERVICE
(continued)
CLONING(continued)
Load MyScreen data
•   Please save the image data as "pj_logo.bmp" or 
"pj_logo.gif" into USB memory.
•   Please note that the only compatible formats are 
as follows.
-File format Windows BMP   bit/pixel: 2/4/8/15/16/24/32bit
Compression format : 
Without compression/RLE
GIF
-Image size: more than 36x36, less than 1280x800
•   If two kinds of file format are saved, "pj_logo.
bmp" will be registered into...

66
OPTION menu
ItemDescription
SERVICE
(continued) INFORMATION
Selecting this item displays a dialog titled “INPUT_INFORMATION”. 
It shows the information about the current input.
• The “FRAME LOCK” message on the dialog means the frame lock 
function is working. 
• This item can't be selected for no signal and sync out.
• When the MY TEXT DISPLAY is set to ON, the MY TEXT is 
displayed together with the input information in the  
INPUT_INFORMATION box (

83).
FACTORY RESET
Selecting OK using the ►...

67
NETWORK menu
Remember that incorrect network settings on this 
projector may cause trouble on the network. Be sure 
to consult with your network administrator before 
connecting to an existing access point on your network.
Select “NETWORK” from the main menu to access the 
following functions. 
Select an item using the ▲/▼ cursor buttons on the 
projector or remote control, and press the ► cursor button on the projector or 
remote control, or ENTER button on the remote control to execute the item....

68
NETWORK menu
ItemDescription
WIRELESS  SETUP
(continued) DHCP  
(Dynamic Host  Configuration  Protocol) Use the ▲/▼ buttons to turn DHCP on/off.
ON  ó OFF
Select OFF when the network does not have DHCP 
enabled. To save the setting, press the ► button.
• When the “DHCP” setting changes to “ON”, it 
takes a little time to obtain IP address from DHCP 
server.
• Auto IP function will be assigned an IP address if 
the projector could not obtain an IP address from 
server even if DHCP is “ON”
IP ADDRESS...

69
NETWORK menu
ItemDescription
WIRELESS  SETUP
(continued) DATE AND 
TIME Use the ▲/▼/◄/► buttons to enter the Year (last 
two digits), Month, Date, Hour and Minute.
• When this item is set, the same item in the 
WIRED SETUP menu is overwritten with the same 
setting (

73). 
• The projector will override this setting and retrieve 
DATE AND TIME information from the Time server 
when SNTP is enabled.  (Date/Time Settings in 
the Network Guide)
• This setting will be reset if the projector is turned...

70
NETWORK menu
ItemDescription
WIRELESS  SETUP
(continued) SSIDUse the ▲/▼ 
buttons to select the 
SSID to display the 
SSID menu.
#1 DEFAULT  ó #2 DEFAULT 
ó #3 DEFAULT
      
 #5 CUSTOM  ó #4 DEFAULT 
Select one of the DEFAULT (#1~#4) and press ► 
or ENTER button.
To adjust CUSTOM
Press the ► or ENTER button when the # 5 
CUSTOM is selected. The SSID #5 CUSTOM 
menu will be appeared.
(1)  
The current SSID will be displayed on the 
first line. If not yet written, the line will be blank. Use 
the...