Dukane Imagepro 8755e-Rj Portable Lcd Projector Users Manual

							
25

Projector Control
Network Restart
Restarts the projector’s network connection.
ItemDescription
RestartRestarts the projector’s network connection in order to activate new configuration settings.
• Restarting requires you to re-log on in order to further control or 
configure the projector via a web browser.
NOTE
Logoff
When logoff is clicked, the logon screen is displayed (6 : Fig.   ).
Projector Status
Displays and configures the current projector status.
ItemDescription
Error StatusDisplays the current error status
Lamp TimeDisplays the usage time for the current lamp.
Filter TimeDisplays the usage time for the current filter.
Power StatusDisplays the current power status.
Input StatusDisplays the current input signal source.
Blank On/OffDisplays the Blank On/Off status.
MuteDisplays the current Mute On/Off status.
FreezeDisplays the current Freeze On/Off status. 
						

							
26

Failure & Warning Alerts via E-mail
Failure & Warning Alerts via E-mail
The projector can automatically send an alert to specified e-mail addresses when 
the projector requires maintenance or has encountered an error.
• Up to five e-mail addresses can be specified.
• The projector may be not able to send e-mail if the projector suddenly loses 
power.
NOTE
Mail Settings(10)
To use the projector’s e-mail function please configure the following items via a 
web browser.
Example: If the IP address of the projector is set to 192.168.1.10:
• A Network Restart is required after the SMTP Port configuration 
settings have changed. Click [Network Restart] and configure the following 
items.
NOTE
 6)   Click 
[Mail Settings] and configure each item. Refer to the [Mail Settings] 
item in [Configuring and Controlling the Projector via a Web Browser] for 
further information.
 

) Click the 
[Apply] button to save the settings.
• Click the [Send Test Mail] button in [Mail Settings] to confirm 
that the e-mail settings are correct. The following mail will be delivered to the 
specified addresses.
NOTE
Subject line   : Test Mail   
Text
  : Send Test Mail
 
  Date   
  Time   
  IP Address   
  MAC Address   
 
 ) Enter 
[https://192.168.1.10] into the address bar of the web browser.
 

) Enter the Administrator ID and Password and click 
[Logon].
 3) Click [Port Settings] on the main menu.
 4) Click the [Enable] check box to open the SMTP Port.
 5) Click the [Apply] button to save the settings. 
						

							


Failure & Warning Alerts via E-mail
 8)  Configure the Failure/Warning Alerts via E-mail settings. Click [Alert Settings] 
on the main menu.
 9) 
 
Select and configure each alert item. Refer to 
[Alert Settings] in [Configuring 
and Controlling the Projector via a Web Browser] for further information.
10) Click the [Apply] button to save the settings.
Failure/Warning e-mails are formatted as follows:
Subject line
  :    
Text 
  : 
 
  Date   
 
Time   
 
IP Address   
 
MAC Address   
Mail Settings (Continued) 
						

							


Projector management via SNMP
Projector management via SNMP
When SNMP is enabled, the projector is able to send Failure/Warning Alerts to a 
specified PC.
• It is recommended that SNMP functions be carried out by a network 
administrator. 
• SNMP management software must be installed on the computer to monitor 
the projector via SNMP.
NOTE
SNMP settings
Configure the following items via a web browser to use SNMP.
Example: If the IP address of the projector is set to 192.168.1.10:
• A Network Restart is required after the SNMP Trap configuration 
settings have been changed. Click [Network Restart] and configure the 
following items.
NOTE
(9)
 5) Click [Security Settings] on the main menu.
 6) Click [SNMP] and set the Community Name on the screen that is displayed.
• A Network Restart is required after the Community Name has been 
changed.
• Click [Network Restart] and configure the following items.
NOTE
 7)   Configure the settings for Trap transmission of Failures/Warnings. Click 
[Alert Settings] on the main menu and select the Failure/Warning item to be 
configured.
 

) 
 
Click the 
[Enable] check box to send out the SNMP trap for Failures/Warnings. 
Clear the [Enable] check box when SNMP trap transmission is not required.
 9) Click the [Apply] button to save the settings.
 

) Enter 
[https://192.168.1.10] into the address bar of the web browser.
 

) Enter the Administrator ID and Password and click 
[Logon].
 3) Click [Port Settings] on the main menu.
 4) 
 
Click the 
[Enable] check box to open the SNMP Port. 
Set the IP address to send the SNMP Trap to when a  Failure/Warning occurs. 
						

							
29

Controlling the Projector via Scheduling
Controlling the Projector via Scheduling
The projector can be automatically controlled via scheduling.
• You can schedule the following control events: Power ON/OFF, Input 
Source and Transferred Image Display. 
• There are 3 types of Scheduling, 1) daily 2) day of the week 3) specific date.
• The priority for scheduled events is as follows 1) specific date 2) day of the 
week 3) daily.
• Up to five specific dates are available for scheduled events. Priority is given to 
those with the lower numbers when more than one event has been scheduled\
 
for the same date and time (e.g., ‘Specific day No. 1’ has priority over ‘Specific 
day No.  ’ and so on. 
• Be sure to set the date and time before enabling scheduled events.
NOTE 
						

							
30

Controlling the Projector via Scheduling
Date/Time Settings
The Date/Time setting can be adjusted via a web browser.
Example: If the IP address of the projector is set to 192.168.1.10:
• A Network Restart is required after the Daylight Savings Time or 
SNTP configuration settings have been changed.
• The battery for the built in clock may be dead if the clock loses time e\
ven 
when the DATE and TIME have been set correctly. Replace the battery by 
following the instructions on replacing the battery.
(User's Manual - Operating Guide : Replacing Internal Clock battery)
• The Internal Clock’s time may not remain accurate. Using SNTP is 
recommended to maintain accurate time.
NOTE
(18)
  )    Enter [https://192.168.1.10] into the address bar of the web browser. 
Enter the Administrator ID and Password and click [Logon].
 

) 
 
Click 
[Date/Time Settings] on the main menu and configure each item. 
Refer to the [Date/Time Settings] item in [Configuring and Controlling the 
Projector via a Web Browser] for further information.
 3) Click the [Apply] button to save the settings. 
						

							
31

Controlling the Projector via Scheduling
Schedule Settings
Schedule settings can be configured from a web browser.
Example: If the IP address of the projector is set to 192.168.1.10:
(16)
There are three types of scheduling.
 1) Daily: Perform the specified operation at a specified time every day.
 2)   Sunday ~ Saturday: Perform the specified operation at the specified time on a 
specified day of the week.
 3) Specific Date: Perform the specified operation on the specified date and time.
• In Standby mode the power indicator will flash green for approx. 3 
seconds when at least 1 “Power ON” schedule is saved.
• When the schedule function is used, the power cord must be connecte\
d to 
the projector and the outlet and the power switch must be turned on, [ |\
 ]. The 
schedule function does not work when the power switch is turned off, [¡] or 
the breaker in a room is tripped. The power indicator will lights orange or green 
when the projector gets is receiving the power.
NOTE
 
 ) Enter 
[https://192.168.1.10] into the address bar of the web browser.
 

) Enter the Administrator ID and Password and click 
[Logon].
 3) 
 
Click 
[Schedule Settings] on the main menu and select the required schedule 
item.
 4) Click the [Enable] check box to enable scheduling.
 5) Enter the Date (Month/Day) for specific date scheduling.
 6)   Click 
[Add] and set the hour, command and parameters and click [Add This 
Schedule] when you want to add a command.
 

) Click the 
[Delete] button when you want to delete a schedule.
 

) Click the 
[Apply] button to save the settings. 
						

							
32

e-Shot (Still Image Transfer) Display
e-Shot (Still Image Transfer) Display
The projector can display a still image that is transferred via the netw\
ork.
Communication Port
The following port is used for e-Shot.
     TCP #9716
(9)
e-Shot (Still Image Transfer) Settings
Configure the following items from a web browser when e-Shot is used.
Example: If the IP address of the projector is set to 192.168.1.10:
• e-Shot is not available via communication ports which are used for 
the command control (TCP #23 and TCP #9715).
NOTE

) Enter 
[https://192.168.1.10] into the address bar of the web browser.

) 
 
Enter the Administrator ID and Password and 
click [Logon]. 
3) Click [Port settings] on the main menu.
4) 
 
Click the 
[Enable] check box to open the 
[Image Transfer Port (Port: 9716)]. Click the 
[Enable] check box for the [Authentication] 
setting when authentication is required, 
otherwise clear the check box.
5) Click the [Apply] button to save the settings. 
						

							
33

e-Shot (Still Image Transfer) Display
e-Shot (Still Image Transfer) Settings (Continued)
When the authentication setting is enabled, the following settings are r\
equired.
 6) Click [Security Settings] on the main menu.
 

) 
 
Select 
[Network Control] and enter the desired authentication password. * 
see Note

 
 

) Click the 
[Apply]  button to save the settings. * see Note 
• The Authentication Password will be the same for [Network Control 
Port1 (Port: 23)], [Network Control Port2 (Port: 9715)], and [Image Transfer 
Port (Port: 9716)].
NOTE1
• The new configuration settings are activated after restarting the 
network. Restart the network connection when any configuration settings are 
changed. The network connection can be restarted using [Network Restart] on 
the main menu.
NOTE2
e-Shot (Still Image Transfer) Transmission
e-Shot transmission requires an exclusive application for your PC.  You can 
download it from the Hitachi web site. Refer to the manual for the appli\
cation for 
instructions. 
						

							
34

Command Control via the Network
Command Control via the Network
You can configure and control the projector via the network using RS-232C 
commands.
Communication Port
The following two ports are assigned for the command control.
     TCP #23
     TCP #9715
Command Control Settings
Configure the following items from a web browser when command control is used.
Example: If the IP address of the projector is set to 192.168.1.10:
• Command control is not available via communication port (TCP 
#9716) that is used for the e-Shot transmission function.
NOTE

) Enter 
[https://192.168.1.10] into the address bar of the web browser.

) Enter the Administrator ID and Password and click 
[Logon].
3) Click [Port settings] on the main menu.
4) 
 
Click the 
[Enable] check box to open [Network Control Port (Port: 23)] to use 
TCP #23. Click the [Enable] check box for the [Authentication] setting when 
authentication is required, otherwise clear the check box.
5) 
 
Click the 
[Enable] check box to open [Network Control Port (Port: 9715)] to 
use TCP #9715. Click the [Enable] check box for the [Authentication] setting 
when authentication is required, otherwise clear the check box. 
6) Click the [Apply] button to save the settings.
(9)